Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 04 8月, 2015 1 次提交
    • M
      xhci: fix off by one error in TRB DMA address boundary check · 7895086a
      由 Mathias Nyman 提交于 
      We need to check that a TRB is part of the current segment
before calculating its DMA address.

Previously a ring segment didn't use a full memory page, and every
new ring segment got a new memory page, so the off by one
error in checking the upper bound was never seen.

Now that we use a full memory page, 256 TRBs (4096 bytes), the off by one
didn't catch the case when a TRB was the first element of the next segment.

This is triggered if the virtual memory pages for a ring segment are
next to each in increasing order where the ring buffer wraps around and
causes errors like:

[  106.398223] xhci_hcd 0000:00:14.0: ERROR Transfer event TRB DMA ptr not part of current TD ep_index 0 comp_code 1
[  106.398230] xhci_hcd 0000:00:14.0: Looking for event-dma fffd3000 trb-start fffd4fd0 trb-end fffd5000 seg-start fffd4000 seg-end fffd4ff0

The trb-end address is one outside the end-seg address.

Cc: <stable@vger.kernel.org>
Tested-by: NArkadiusz Miśkiewicz <arekm@maven.pl>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      7895086a
  3. 23 7月, 2015 1 次提交
  5. 31 5月, 2015 2 次提交
    • M
      xhci: Return correct number of tranferred bytes for stalled control endpoints · 22ae47e6
      由 Mathias Nyman 提交于 
      Fix the xhci driver from bluntly setting the transferred length to 0 if
we get a STALL on anything else than the data stage of a control transfer.
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      22ae47e6
    • R
      usb: xhci: fix xhci locking up during hcd remove · ad6b1d91
      由 Roger Quadros 提交于 
      The problem seems to be that if a new device is detected
while we have already removed the shared HCD, then many of the
xhci operations (e.g.  xhci_alloc_dev(), xhci_setup_device())
hang as command never completes.

I don't think XHCI can operate without the shared HCD as we've
already called xhci_halt() in xhci_only_stop_hcd() when shared HCD
goes away. We need to prevent new commands from being queued
not only when HCD is dying but also when HCD is halted.

The following lockup was detected while testing the otg state
machine.

[  178.199951] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[  178.205799] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[  178.214458] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x00010010
[  178.223619] xhci-hcd xhci-hcd.0.auto: irq 400, io mem 0x48890000
[  178.230677] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[  178.237796] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[  178.245358] usb usb1: Product: xHCI Host Controller
[  178.250483] usb usb1: Manufacturer: Linux 4.0.0-rc1-00024-g6111320 xhci-hcd
[  178.257783] usb usb1: SerialNumber: xhci-hcd.0.auto
[  178.267014] hub 1-0:1.0: USB hub found
[  178.272108] hub 1-0:1.0: 1 port detected
[  178.278371] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[  178.284171] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[  178.294038] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[  178.301183] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[  178.308776] usb usb2: Product: xHCI Host Controller
[  178.313902] usb usb2: Manufacturer: Linux 4.0.0-rc1-00024-g6111320 xhci-hcd
[  178.321222] usb usb2: SerialNumber: xhci-hcd.0.auto
[  178.329061] hub 2-0:1.0: USB hub found
[  178.333126] hub 2-0:1.0: 1 port detected
[  178.567585] dwc3 48890000.usb: usb_otg_start_host 0
[  178.572707] xhci-hcd xhci-hcd.0.auto: remove, state 4
[  178.578064] usb usb2: USB disconnect, device number 1
[  178.586565] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[  178.592585] xhci-hcd xhci-hcd.0.auto: remove, state 1
[  178.597924] usb usb1: USB disconnect, device number 1
[  178.603248] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[  190.597337] INFO: task kworker/u4:0:6 blocked for more than 10 seconds.
[  190.604273]       Not tainted 4.0.0-rc1-00024-g6111320 #1058
[  190.610228] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[  190.618443] kworker/u4:0    D c05c0ac0     0     6      2 0x00000000
[  190.625120] Workqueue: usb_otg usb_otg_work
[  190.629533] [<c05c0ac0>] (__schedule) from [<c05c10ac>] (schedule+0x34/0x98)
[  190.636915] [<c05c10ac>] (schedule) from [<c05c1318>] (schedule_preempt_disabled+0xc/0x10)
[  190.645591] [<c05c1318>] (schedule_preempt_disabled) from [<c05c23d0>] (mutex_lock_nested+0x1ac/0x3fc)
[  190.655353] [<c05c23d0>] (mutex_lock_nested) from [<c046cf8c>] (usb_disconnect+0x3c/0x208)
[  190.664043] [<c046cf8c>] (usb_disconnect) from [<c0470cf0>] (_usb_remove_hcd+0x98/0x1d8)
[  190.672535] [<c0470cf0>] (_usb_remove_hcd) from [<c0485da8>] (usb_otg_start_host+0x50/0xf4)
[  190.681299] [<c0485da8>] (usb_otg_start_host) from [<c04849a4>] (otg_set_protocol+0x5c/0xd0)
[  190.690153] [<c04849a4>] (otg_set_protocol) from [<c0484b88>] (otg_set_state+0x170/0xbfc)
[  190.698735] [<c0484b88>] (otg_set_state) from [<c0485740>] (otg_statemachine+0x12c/0x470)
[  190.707326] [<c0485740>] (otg_statemachine) from [<c0053c84>] (process_one_work+0x1b4/0x4a0)
[  190.716162] [<c0053c84>] (process_one_work) from [<c00540f8>] (worker_thread+0x154/0x44c)
[  190.724742] [<c00540f8>] (worker_thread) from [<c0058f88>] (kthread+0xd4/0xf0)
[  190.732328] [<c0058f88>] (kthread) from [<c000e810>] (ret_from_fork+0x14/0x24)
[  190.739898] 5 locks held by kworker/u4:0/6:
[  190.744274]  #0:  ("%s""usb_otg"){.+.+.+}, at: [<c0053bf4>] process_one_work+0x124/0x4a0
[  190.752799]  #1:  ((&otgd->work)){+.+.+.}, at: [<c0053bf4>] process_one_work+0x124/0x4a0
[  190.761326]  #2:  (&otgd->fsm.lock){+.+.+.}, at: [<c048562c>] otg_statemachine+0x18/0x470
[  190.769934]  #3:  (usb_bus_list_lock){+.+.+.}, at: [<c0470ce8>] _usb_remove_hcd+0x90/0x1d8
[  190.778635]  #4:  (&dev->mutex){......}, at: [<c046cf8c>] usb_disconnect+0x3c/0x208
[  190.786700] INFO: task kworker/1:0:14 blocked for more than 10 seconds.
[  190.793633]       Not tainted 4.0.0-rc1-00024-g6111320 #1058
[  190.799567] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[  190.807783] kworker/1:0     D c05c0ac0     0    14      2 0x00000000
[  190.814457] Workqueue: usb_hub_wq hub_event
[  190.818866] [<c05c0ac0>] (__schedule) from [<c05c10ac>] (schedule+0x34/0x98)
[  190.826252] [<c05c10ac>] (schedule) from [<c05c4e40>] (schedule_timeout+0x13c/0x1ec)
[  190.834377] [<c05c4e40>] (schedule_timeout) from [<c05c19f0>] (wait_for_common+0xbc/0x150)
[  190.843062] [<c05c19f0>] (wait_for_common) from [<bf068a3c>] (xhci_setup_device+0x164/0x5cc [xhci_hcd])
[  190.852986] [<bf068a3c>] (xhci_setup_device [xhci_hcd]) from [<c046b7f4>] (hub_port_init+0x3f4/0xb10)
[  190.862667] [<c046b7f4>] (hub_port_init) from [<c046eb64>] (hub_event+0x704/0x1018)
[  190.870704] [<c046eb64>] (hub_event) from [<c0053c84>] (process_one_work+0x1b4/0x4a0)
[  190.878919] [<c0053c84>] (process_one_work) from [<c00540f8>] (worker_thread+0x154/0x44c)
[  190.887503] [<c00540f8>] (worker_thread) from [<c0058f88>] (kthread+0xd4/0xf0)
[  190.895076] [<c0058f88>] (kthread) from [<c000e810>] (ret_from_fork+0x14/0x24)
[  190.902650] 5 locks held by kworker/1:0/14:
[  190.907023]  #0:  ("usb_hub_wq"){.+.+.+}, at: [<c0053bf4>] process_one_work+0x124/0x4a0
[  190.915454]  #1:  ((&hub->events)){+.+.+.}, at: [<c0053bf4>] process_one_work+0x124/0x4a0
[  190.924070]  #2:  (&dev->mutex){......}, at: [<c046e490>] hub_event+0x30/0x1018
[  190.931768]  #3:  (&port_dev->status_lock){+.+.+.}, at: [<c046eb50>] hub_event+0x6f0/0x1018
[  190.940558]  #4:  (&bus->usb_address0_mutex){+.+.+.}, at: [<c046b458>] hub_port_init+0x58/0xb10
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      ad6b1d91
  7. 10 5月, 2015 2 次提交
  9. 08 4月, 2015 1 次提交
  11. 18 3月, 2015 1 次提交
  13. 11 3月, 2015 1 次提交
  15. 07 3月, 2015 1 次提交
    • A
      xhci: fix reporting of 0-sized URBs in control endpoint · 45ba2154
      由 Aleksander Morgado 提交于 
      When a control transfer has a short data stage, the xHCI controller generates
two transfer events: a COMP_SHORT_TX event that specifies the untransferred
amount, and a COMP_SUCCESS event. But when the data stage is not short, only the
COMP_SUCCESS event occurs. Therefore, xhci-hcd must set urb->actual_length to
urb->transfer_buffer_length while processing the COMP_SUCCESS event, unless
urb->actual_length was set already by a previous COMP_SHORT_TX event.

The driver checks this by seeing whether urb->actual_length == 0, but this alone
is the wrong test, as it is entirely possible for a short transfer to have an
urb->actual_length = 0.

This patch changes the xhci driver to rely on a new td->urb_length_set flag,
which is set to true when a COMP_SHORT_TX event is received and the URB length
updated at that stage.

This fixes a bug which affected the HSO plugin, which relies on URBs with
urb->actual_length == 0 to halt re-submitting the RX URB in the control
endpoint.

Cc: <stable@vger.kernel.org>
Signed-off-by: NAleksander Morgado <aleksander@aleksander.es>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      45ba2154
  17. 25 2月, 2015 1 次提交
  19. 10 1月, 2015 3 次提交
  21. 03 12月, 2014 2 次提交
  23. 22 11月, 2014 2 次提交
    • M
      USB: xhci: Reset a halted endpoint immediately when we encounter a stall. · 8e71a322
      由 Mathias Nyman 提交于 
      If a device is halted and reuturns a STALL, then the halted endpoint
needs to be cleared both on the host and device side. The host
side halt is cleared by issueing a xhci reset endpoint command. The device side
is cleared with a ClearFeature(ENDPOINT_HALT) request, which should
be issued by the device driver if a URB reruen -EPIPE.

Previously we cleared the host side halt after the device side was cleared.
To make sure the host side halt is cleared in time we want to issue the
reset endpoint command immedialtely when a STALL status is encountered.

Otherwise we end up not following the specs and not returning -EPIPE
several times in a row when trying to transfer data to a halted endpoint.

Fixes: bcef3fd5 (USB: xhci: Handle errors that cause endpoint halts.)
Cc: <stable@vger.kernel.org> # v2.6.33+
Tested-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      8e71a322
    • M
      USB: xhci: don't start a halted endpoint before its new dequeue is set · c3492dbf
      由 Mathias Nyman 提交于 
      A halted endpoint ring must first be reset, then move the ring
dequeue pointer past the problematic TRB. If we start the ring too
early after reset, but before moving the dequeue pointer we
will end up executing the same problematic TRB again.

As we always issue a set transfer dequeue command after a reset
endpoint command we can skip starting endpoint rings at reset endpoint
command completion.

Without this fix we end up trying to handle the same faulty TD for
contol endpoints. causing timeout, and failing testusb ctrl_out write
tests.

Fixes: e9df17eb (USB: xhci: Correct assumptions about number of rings per endpoint.)
Cc: <stable@vger.kernel.org> #v2.6.35
Tested-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      c3492dbf
  25. 24 9月, 2014 5 次提交
  27. 20 8月, 2014 2 次提交
  29. 02 8月, 2014 1 次提交
  31. 25 6月, 2014 2 次提交
  33. 20 5月, 2014 4 次提交
    • M
      xhci: rework command timeout and cancellation, · c311e391
      由 Mathias Nyman 提交于 
      Use one timer to control command timeout.

start/kick the timer every time a command is completed and a
new command is waiting, or a new command is added to a empty list.

If the timer runs out, then tag the current command as "aborted", and
start the xhci command abortion process.

Previously each function that submitted a command had its own timer.
If that command timed out, a new command structure for the
command was created and it was put on a cancel_cmd_list list,
then a pci write to abort the command ring was issued.

when the ring was aborted, it checked if the current command
was the one to be canceled, later when the ring was stopped the
driver got ownership of the TRBs in the command ring,
compared then to the TRBs in the cancel_cmd_list,
and turned them into No-ops.

Now, instead, at timeout we tag the status of the command in the
command queue to be aborted, and start the ring abortion.
Ring abortion stops the command ring and gives control of the
commands to us.
All the aborted commands are now turned into No-ops.

If the ring is already stopped when the command times outs its not possible
to start the ring abortion, in this case the command is turnd to No-op
right away.

All these changes allows us to remove the entire cancel_cmd_list code.

The functions waiting for a command to finish no longer have their own timeouts.
They will wait either until the command completes normally,
or until the whole command abortion is done.
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      c311e391
    • M
      xhci: Use completion and status in global command queue · 9ea1833e
      由 Mathias Nyman 提交于 
      Remove the per-device command list and handle_cmd_in_cmd_wait_list()
and use the completion and status variables found in the
command structure in the global command list.
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      9ea1833e
    • M
      xhci: Add a global command queue · c9aa1a2d
      由 Mathias Nyman 提交于 
      Create a list to store command structures, add a structure to it every time
a command is submitted, and remove it from the list once we get a
command completion event matching the command.

Callers that wait for completion will free their command structures themselves.
The other command structures are freed in the command completion event handler.

Also add a check that prevents queuing commands if host is dying
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      c9aa1a2d
    • M
      xhci: Use command structures when queuing commands on the command ring · ddba5cd0
      由 Mathias Nyman 提交于 
      To create a global command queue we require that each command put on the
command ring is submitted with a command structure.

Functions that queue commands and wait for completion need to allocate a command
before submitting it, and free it once completed. The following command queuing
functions need to be modified.

xhci_configure_endpoint()
xhci_address_device()
xhci_queue_slot_control()
xhci_queue_stop_endpoint()
xhci_queue_new_dequeue_state()
xhci_queue_reset_ep()
xhci_configure_endpoint()

xhci_configure_endpoint() could already be called with a command structure,
and only xhci_check_maxpacket and xhci_check_bandwidth did not do so. These
are changed and a command structure is now required. This change also simplifies
the configure endpoint command completion handling and the "goto bandwidth_change"
handling code can be removed.

In some cases the command queuing function is called in interrupt context.
These commands needs to be allocated atomically, and they can't wait for
completion. These commands will in this patch be freed directly after queuing,
but freeing will be moved to the command completion event handler in a later
patch once we get the global command queue up.(Just so that we won't leak
memory in the middle of the patch set)
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      ddba5cd0
  35. 26 4月, 2014 1 次提交
    • J
      usb: xhci: Prefer endpoint context dequeue pointer over stopped_trb · 1f81b6d2
      由 Julius Werner 提交于 
      We have observed a rare cycle state desync bug after Set TR Dequeue
Pointer commands on Intel LynxPoint xHCs (resulting in an endpoint that
doesn't fetch new TRBs and thus an unresponsive USB device). It always
triggers when a previous Set TR Dequeue Pointer command has set the
pointer to the final Link TRB of a segment, and then another URB gets
enqueued and cancelled again before it can be completed. Further
investigation showed that the xHC had returned the Link TRB in the TRB
Pointer field of the Transfer Event (CC == Stopped -- Length Invalid),
but when xhci_find_new_dequeue_state() later accesses the Endpoint
Context's TR Dequeue Pointer field it is set to the first TRB of the
next segment.

The driver expects those two values to be the same in this situation,
and uses the cycle state of the latter together with the address of the
former. This should be fine according to the XHCI specification, since
the endpoint ring should be stopped when returning the Transfer Event
and thus should not advance over the Link TRB before it gets restarted.
However, real-world XHCI implementations apparently don't really care
that much about these details, so the driver should follow a more
defensive approach to try to work around HC spec violations.

This patch removes the stopped_trb variable that had been used to store
the TRB Pointer from the last Transfer Event of a stopped TRB. Instead,
xhci_find_new_dequeue_state() now relies only on the Endpoint Context,
requiring a small amount of additional processing to find the virtual
address corresponding to the TR Dequeue Pointer. Some other parts of the
function were slightly rearranged to better fit into this model.

This patch should be backported to kernels as old as 2.6.31 that contain
the commit ae636747 "USB: xhci: URB
cancellation support."
Signed-off-by: NJulius Werner <jwerner@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      1f81b6d2
  37. 05 3月, 2014 6 次提交
  39. 08 2月, 2014 1 次提交