We need to check that a TRB is part of the current segment
before calculating its DMA address.

Previously a ring segment didn't use a full memory page, and every
new ring segment got a new memory page, so the off by one
error in checking the upper bound was never seen.

Now that we use a full memory page, 256 TRBs (4096 bytes), the off by one
didn't catch the case when a TRB was the first element of the next segment.

This is triggered if the virtual memory pages for a ring segment are
next to each in increasing order where the ring buffer wraps around and
causes errors like:

[  106.398223] xhci_hcd 0000:00:14.0: ERROR Transfer event TRB DMA ptr not part of current TD ep_index 0 comp_code 1
[  106.398230] xhci_hcd 0000:00:14.0: Looking for event-dma fffd3000 trb-start fffd4fd0 trb-end fffd5000 seg-start fffd4000 seg-end fffd4ff0

The trb-end address is one outside the end-seg address.

Cc: <stable@vger.kernel.org>
Tested-by: NArkadiusz Miśkiewicz <arekm@maven.pl>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes a bug in the error pathway of
usb_add_gadget_udc_release() in udc-core.c.  If the udc registration
fails, the gadget registration is not fully undone; there's a
put_device(&gadget->dev) call but no device_del().

CC: <stable@vger.kernel.org>
Acked-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add support for the Sierra Wireless AR8550 device with
USB descriptor 0x1199, 0x68AB.

It is common with MC879x modules 1199:683c/683d which
also are composite devices with 7 interfaces (0..6)
and also MDM62xx based as the AR8550.

The major difference are only the interface attributes
02/02/01 on interfaces 3 and 4 on the AR8550. They are
vendor specific ff/ff/ff on MC879x modules.

lsusb reports:

Bus 001 Device 004: ID 1199:68ab Sierra Wireless, Inc.
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0        64
  idVendor           0x1199 Sierra Wireless, Inc.
  idProduct          0x68ab
  bcdDevice            0.06
  iManufacturer           3 Sierra Wireless, Incorporated
  iProduct                2 AR8550
  iSerial                 0
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength          198
    bNumInterfaces          7
    bConfigurationValue     1
    iConfiguration          1 Sierra Configuration
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass    255 Vendor Specific Subclass
      bInterfaceProtocol    255 Vendor Specific Protocol
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval              32
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x01  EP 1 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval              32
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        1
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass    255 Vendor Specific Subclass
      bInterfaceProtocol    255 Vendor Specific Protocol
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x82  EP 2 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval              32
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x02  EP 2 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval              32
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        2
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass    255 Vendor Specific Subclass
      bInterfaceProtocol    255 Vendor Specific Protocol
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x83  EP 3 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval              32
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x03  EP 3 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval              32
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        3
      bAlternateSetting       0
      bNumEndpoints           3
      bInterfaceClass         2 Communications
      bInterfaceSubClass      2 Abstract (modem)
      bInterfaceProtocol      1 AT-commands (v.25ter)
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x84  EP 4 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval               5
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x85  EP 5 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval              32
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x04  EP 4 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval              32
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        4
      bAlternateSetting       0
      bNumEndpoints           3
      bInterfaceClass         2 Communications
      bInterfaceSubClass      2 Abstract (modem)
      bInterfaceProtocol      1 AT-commands (v.25ter)
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x86  EP 6 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval               5
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x87  EP 7 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval              32
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x05  EP 5 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval              32
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        5
      bAlternateSetting       0
      bNumEndpoints           3
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass    255 Vendor Specific Subclass
      bInterfaceProtocol    255 Vendor Specific Protocol
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x88  EP 8 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval               5
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x89  EP 9 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval              32
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x06  EP 6 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval              32
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        6
      bAlternateSetting       0
      bNumEndpoints           3
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass    255 Vendor Specific Subclass
      bInterfaceProtocol    255 Vendor Specific Protocol
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x8a  EP 10 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval               5
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x8b  EP 11 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval              32
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x07  EP 7 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval              32
Device Qualifier (for other device speed):
  bLength                10
  bDescriptorType         6
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0        64
  bNumConfigurations      1
Device Status:     0x0001
  Self Powered
Signed-off-by: NDirk Behme <dirk.behme@de.bosch.com>
Cc: Lars Melin <larsm17@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

There is a predefined maximum number of printer instances, currently 4.
A chrdev region is allocated accordingly, but with configfs the user
can create as many printer function directories as they like. To make the
number of printer  instances consistent with the number of allocated
minors, the limit is enforced at directory creation time.
Signed-off-by: NAndrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

There is a predefined maximum number of hid instances, currently 4.
A chrdev region is allocated accordingly, but with configfs the user
can create as many hid function directories as they like. To make
the number of hid instances consistent with the number of allocated minors,
the limit is enforced at directory creation time.
Signed-off-by: NAndrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The p_interval should be less if the 'bInterval' at the descriptor
is larger, eg, if 'bInterval' is 5 for HS, the p_interval should be
8000 / 16 = 500.

It fixes the patch 9bb87f16 ("usb: gadget: f_uac2: send
reasonably sized packets")

Cc: <stable@vger.kernel.org> # v3.18+
Fixes: 9bb87f16 ("usb: gadget: f_uac2: send reasonably sized packets")
Acked-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

ep_dequeue() in bdc_ep.c was capturing the hw dequeue pointer
incorrectly by reading the wrong register for the upper 32 bits.
Signed-off-by: NAl Cooper <alcooperx@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This reverts commit 23c40591 ("parport: fix memory leak")

par_dev->state was already being removed in parport_unregister_device().
Reported-by: NYing Huang <ying.huang@intel.com>
Signed-off-by: NSudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

A new BLK namespace "seed" device is created whenever the current seed
is successfully probed.  However, if that namespace is assigned to a BTT
it may never directly experience a successful probe as it is a
subordinate device to a BTT configuration.

The effect of the current code is that no new namespaces can be
instantiated, after the seed namespace, to consume available BLK DPA
capacity.  Fix this by treating a successful BTT probe event as a
successful probe event for the backing namespace.
Reported-by: NNicholas Moulin <nicholas.w.moulin@linux.intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

The touchscreen on the WinBook TW100 and TW700 don't match the default
display, with 0,0 touches being reported when touching at the bottom
right of the screen.

  1280,800             0,800
         +-------------+
         |             |
         |             |
         |             |
         +-------------+
    1280,0             0,0

It's unfortunately impossible to detect this problem with data from the
DSDT, or other auxiliary metadata, so fallback to quirking this specific
model of tablet instead.
Signed-off-by: NBastien Nocera <hadess@hadess.net>
Reviewed-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Devices may declare more LEDs than what is known to input-leds
(HID does this for some devices). Instead of showing ugly warnings
on connect and, even worse, oopsing on disconnect, let's simply
ignore LEDs that are not known to us.
Reported-and-tested-by: NVlastimil Babka <vbabka@suse.cz>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

DMA transfers must be greater than the watermark level size. spi_imx->rx_wml
and spi_imx->tx_wml contain the watermark level in 32bit words whereas struct
spi_transfer contains the transfer len in bytes. Fix the check if DMA is
possible for a transfer accordingly. This fixes transfers with sizes between
33 and 128 bytes for which previously was claimed that DMA is possible.

Fixes: f62caccd (spi: spi-imx: add DMA support)
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: NMark Brown <broonie@kernel.org>

pdev->dev.platform_data is not initialized if match is true in function
sdhci_pxav3_probe. Just local variable pdata is assigned the return value
from function pxav3_get_mmc_pdata().

static int sdhci_pxav3_probe(struct platform_device *pdev) {

    struct sdhci_pxa_platdata *pdata = pdev->dev.platform_data;
    ...
    if (match) {
		ret = mmc_of_parse(host->mmc);
		if (ret)
			goto err_of_parse;
		sdhci_get_of_property(pdev);
		pdata = pxav3_get_mmc_pdata(dev);
     }
     ...
}
Signed-off-by: NJingju Hou <houjingj@marvell.com>
Fixes: b650352d("mmc: sdhci-pxa: Add device tree support")
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

After commit 8d86e4fc ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()"),
it's not used anymore.
Signed-off-by: NDong Aisheng <aisheng.dong@freescale.com>
Reviewed-by: NJohan Derycke <johan.derycke@barco.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

After commit 8d86e4fc ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()"),
we do not need those duplicated parsing anymore.

Note: fsl,cd-controller is also deleted due to the driver does
not support controller card detection anymore after switch to runtime pm.
And there's no user of it right now in device tree.

wp-gpios is kept because we're still support fsl,wp-controller,
so we need a way to check if it's gpio wp or controller wp.
Signed-off-by: NDong Aisheng <aisheng.dong@freescale.com>
Reviewed-by: NJohan Derycke <johan.derycke@barco.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Device tree provides option to specify the max freqency with property
"max-frequency" in dts and common parse function mmc_of_parse() will
parse it and use this value to set host->f_max to tell the MMC core
the maxinum frequency the host works.

However, current sdhci driver will finally overwrite this value with
host->max_clk regardless of the max-frequency property.

This patch makes sure not overwrite the max-frequency set from device
tree and do basic sanity check.
Signed-off-by: NDong Aisheng <aisheng.dong@freescale.com>
Reviewed-by: NJohan Derycke <johan.derycke@barco.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This is an incremental fix of commit
e62bd351b("mmc: sdhci-esdhc-imx: Do not break platform data boards").

After commit 8d86e4fc ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()"),
we do not need to run the check of boarddata->wp_type/cd_type/max_bus_width
again for dt platform since those are already handled by mmc_of_parse().

Current code only exclude the checking of wp_type for dt platform which
does not make sense.

This patch moves all non dt probe code into one function.
Besides, since we only support SD3.0/eMMC HS200 for dt platform, the
support_vsel checking and ultra high speed pinctrl state are also merged
into sdhci_esdhc_imx_probe_dt.

Then we have two separately probe function for dt and non dt type.
This can make the driver probe more clearly.
Signed-off-by: NDong Aisheng <aisheng.dong@freescale.com>
Reviewed-by: NJohan Derycke <johan.derycke@barco.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Current card detect probe process is that when driver finds a valid
ESDHC_CD_GPIO, it will clear the quirk SDHCI_QUIRK_BROKEN_CARD_DETECTION
which is set by default for all esdhc/usdhc controllers.
Then host driver will know there's a valid card detect function.

Commit 8d86e4fc ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()")
breaks GPIO CD function for dt platform that it will return directly
when find ESDHC_CD_GPIO for dt platform which result in the later wrongly
to keep SDHCI_QUIRK_BROKEN_CARD_DETECTION for all dt platforms.
Then MMC_CAP_NEEDS_POLL will be used instead even there's a valid
GPIO card detect.

This patch adds back this function and follows the original approach to
clear the quirk if find an valid CD GPIO for dt platforms.

Fixes: 8d86e4fc ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()")
Signed-off-by: NDong Aisheng <aisheng.dong@freescale.com>
Reviewed-by: NJohan Derycke <johan.derycke@barco.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Support for 8BIT bus with was added some time ago to sdhci-esdhc but
then missed to remove the 8BIT from the reserved bit mask which made
8BIT non functional.

Fixes: 66b50a00 ("mmc: esdhc: Add support for 8-bit bus width and..")
Signed-off-by: NJoakim Tjernlund <joakim.tjernlund@transmode.se>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Enclosing mmc_blk_put() is missing in power_ro_lock_show() sysfs handler,
let's add it.

Fixes: add710ea ("mmc: boot partition ro lock support")
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

If NO_DMA=y:

    ERROR: "dma_alloc_coherent" [drivers/mmc/host/mtk-sd.ko] undefined!
    ERROR: "dma_unmap_sg" [drivers/mmc/host/mtk-sd.ko] undefined!
    ERROR: "dma_map_sg" [drivers/mmc/host/mtk-sd.ko] undefined!
    ERROR: "dma_free_coherent" [drivers/mmc/host/mtk-sd.ko] undefined!

Add a dependency on HAS_DMA to fix this.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

We should not call dma_free_coherent if host->adma_table is NULL,
otherwise may trigger panic.

Fixes: d1e49f77 ("mmc: sdhci: convert ADMA descriptors to a...")
Signed-off-by: NPeng Fan <van.freenix@gmail.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Sometimes BADA, DEB or CEB error interrupts occur when sd card is
unplugged during data transfer. These interrupts are currently ignored
by the interrupt handler. But, this results in card not being
recognised on subsequent insertion. This is because mmcqd is waiting
forever for the data transfer(for which error occurred) to complete.
Fix this, by reporting BADA, DEB, CEB errors to mmc-core as -EILSEQ, so
that the core can do appropriate handling.
Signed-off-by: NVignesh R <vigneshr@ti.com>
Tested-by: NAndreas Fenkart <afenkart@gmail.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

DTO/DCRC errors were not being informed to the mmc core since
commit ae4bf788 ("mmc: omap_hsmmc: consolidate error report handling of
HSMMC IRQ"). This commit made sure 'end_trans' is never set on DTO/DCRC
errors. This is because after this commit 'host->data' is checked after
it has been cleared to NULL by omap_hsmmc_dma_cleanup().

Because 'end_trans' is never set, omap_hsmmc_xfer_done() is never invoked
making core layer not to be aware of DTO/DCRC errors. Because of this
any command invoked after DTO/DCRC error leads to a hang.

Fix this by checking for 'host->data' before it is actually cleared.

Fixes: ae4bf788 ("mmc: omap_hsmmc: consolidate error report handling of
HSMMC IRQ")

CC: stable@vger.kernel.org
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NVignesh R <vigneshr@ti.com>
Tested-by: NAndreas Fenkart <afenkart@gmail.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This flag is currently never cleared, which can in rare cases
trigger a warn-on if it is still set but the block isn't
InSync.

So clear it when it isn't need, which includes if the replacement
device has failed.
Signed-off-by: NNeilBrown <neilb@suse.com>

During a node failure, We need to suspend read balancing so that the
reads are directed to the first device and stale data is not read.
Suspending writes is not required because these would be recorded and
synced eventually.

A new flag MD_CLUSTER_SUSPEND_READ_BALANCING is set in recover_prep().
area_resyncing() will respond true for the entire devices if this
flag is set and the request type is READ. The flag is cleared
in recover_done().
Signed-off-by: NGoldwyn Rodrigues <rgoldwyn@suse.com>
Reported-By: NDavid Teigland <teigland@redhat.com>
Signed-off-by: NNeilBrown <neilb@suse.com>

bitmap_read_sb is modifying mddev->bitmap_info.offset. This works for
the first bitmap read. However, when multiple bitmaps need to be opened
by the same node, it ends up corrupting the offset. Fix it by using a
local variable.

Also, bitmap_read_sb is not required in bitmap_copy_from_slot since
it is called in bitmap_create. Remove bitmap_read_sb().
Signed-off-by: NGoldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: NNeilBrown <neilb@suse.com>

request_module() can return 256 (process exited) in some cases,
which is not as specified in the documentation before the
request_module() definition. Convert the error to -ENOENT.

The positive error number results in bitmap_create() returning
a value that is meant to be an error but doesn't look like one,
so it is dereferenced as a point and causes a crash.

(not needed for stable as this is "experimental" code)
Fixes: edb39c9d ("Introduce md_cluster_operations to handle cluster functions")
Signed-off-By: NGoldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: NNeilBrown <neilb@suse.com>

If the bitmap read fails, the error code set is -EINVAL. However,
we don't check for errors and go ahead with cluster_setup.
Skip the cluster setup in case of error.
Signed-off-by: NGoldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: NNeilBrown <neilb@suse.com>

When we get a read error from the last working device, we don't
try to repair it, and don't fail the device.  We simple report a
read error to the caller.

However the current test for 'is this the last working device' is
wrong.
When there is only one fully working device, it assumes that a
non-faulty device is that device.  However a spare which is rebuilding
would be non-faulty but so not the only working device.

So change the test from "!Faulty" to "In_sync".  If ->degraded says
there is only one fully working device and this device is in_sync,
this must be the one.

This bug has existed since we allowed read_balance to read from
a recovering spare in v3.0
Reported-and-tested-by: NAlexander Lyakas <alex.bolshoy@gmail.com>
Fixes: 76073054 ("md/raid1: clean up read_balance.")
Cc: stable@vger.kernel.org (v3.0+)
Signed-off-by: NNeilBrown <neilb@suse.com>

Return proper pgprot for ARM64. This is required for objects like
Nouveau fences to be mapped with expected coherency.
Signed-off-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Pasting text with gpm on a VC produced warning [1]. Reset task state
to TASK_RUNNING in the paste_selection() loop, if the loop did not
sleep.

[1]
WARNING: CPU: 6 PID: 1960 at /home/peter/src/kernels/mainline/kernel/sched/core.c:7286 __might_sleep+0x7f/0x90()
do not call blocking ops when !TASK_RUNNING; state=1 set at [<ffffffff8151805e>] paste_selection+0x9e/0x1a0
Modules linked in: btrfs xor raid6_pq ufs qnx4 hfsplus hfs minix ntfs msdos jfs xfs libcrc32c .....
CPU: 6 PID: 1960 Comm: gpm Not tainted 4.1.0-rc7+tty-xeon+debug #rc7+tty
Hardware name: Dell Inc. Precision WorkStation T5400  /0RW203, BIOS A11 04/30/2012
 ffffffff81c9c0a0 ffff8802b0fd3ac8 ffffffff8185778a 0000000000000001
 ffff8802b0fd3b18 ffff8802b0fd3b08 ffffffff8108039a ffffffff82ae8510
 ffffffff81c9ce00 0000000000000015 0000000000000000 0000000000000000
Call Trace:
 [<ffffffff8185778a>] dump_stack+0x4f/0x7b
 [<ffffffff8108039a>] warn_slowpath_common+0x8a/0xc0
 [<ffffffff81080416>] warn_slowpath_fmt+0x46/0x50
 [<ffffffff810ddced>] ? __lock_acquire+0xe2d/0x13a0
 [<ffffffff8151805e>] ? paste_selection+0x9e/0x1a0
 [<ffffffff8151805e>] ? paste_selection+0x9e/0x1a0
 [<ffffffff810ad4ff>] __might_sleep+0x7f/0x90
 [<ffffffff8185f76a>] down_read+0x2a/0xa0
 [<ffffffff810bb1d8>] ? sched_clock_cpu+0xb8/0xe0
 [<ffffffff8150d1dc>] n_tty_receive_buf_common+0x4c/0xba0
 [<ffffffff810dc875>] ? mark_held_locks+0x75/0xa0
 [<ffffffff81861c95>] ? _raw_spin_unlock_irqrestore+0x65/0x80
 [<ffffffff810b49a1>] ? get_parent_ip+0x11/0x50
 [<ffffffff8150dd44>] n_tty_receive_buf2+0x14/0x20
 [<ffffffff81518117>] paste_selection+0x157/0x1a0
 [<ffffffff810b77b0>] ? wake_up_state+0x20/0x20
 [<ffffffff815203f8>] tioclinux+0xb8/0x2c0
 [<ffffffff81515bfe>] vt_ioctl+0xaee/0x11a0
 [<ffffffff810baf75>] ? sched_clock_local+0x25/0x90
 [<ffffffff810bbe11>] ? vtime_account_user+0x91/0xa0
 [<ffffffff8150810c>] tty_ioctl+0x20c/0xe20
 [<ffffffff810bbe11>] ? vtime_account_user+0x91/0xa0
 [<ffffffff810b49a1>] ? get_parent_ip+0x11/0x50
 [<ffffffff810b4a69>] ? preempt_count_sub+0x49/0x50
 [<ffffffff811ab71c>] ? context_tracking_exit+0x5c/0x290
 [<ffffffff811ab71c>] ? context_tracking_exit+0x5c/0x290
 [<ffffffff81248b98>] do_vfs_ioctl+0x318/0x570
 [<ffffffff810dca8d>] ? trace_hardirqs_on+0xd/0x10
 [<ffffffff810dc9b5>] ? trace_hardirqs_on_caller+0x115/0x1e0
 [<ffffffff81254acc>] ? __fget_light+0x6c/0xa0
 [<ffffffff81248e71>] SyS_ioctl+0x81/0xa0
 [<ffffffff81862832>] system_call_fastpath+0x16/0x7a
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

While closing, new rx data may be received after the input buffers
have been flushed but before stop_rx() halts receiving [1]. The
new data might not be processed by flush_to_ldisc() until after
uart_shutdown() and normal input processing is re-enabled (ie.,
tty->closing = 0). The race is outlined below:

CPU 0                         | CPU 1
                              |
uart_close()                  |
   tty_port_close_start()     |
      tty->closing = 1        |
      tty_ldisc_flush()       |
                              | => IRQ
                              |   while (LSR & data ready)
                              |      uart_insert_char()
                              |   tty_flip_buffer_push()
                              | <= EOI
   stop_rx()                  |   .
   uart_shutdown()            |   .
      free xmit.buf           |   .
   tty_port_tty_set(NULL)     |   .
   tty->closing = 0           |   .
                              | flush_to_ldisc()
                              |   n_tty_receive_buf_common()
                              |      __receive_buf()
                              |         ...
                              |         commit_echoes()
                              |            uart_flush_chars()
                              |               __uart_start()
                              | ** OOPS on port.tty deref **
   tty_ldisc_flush()          |

Input processing must be prevented from echoing (tty->closing = 1)
until _after_ the input buffers have been flushed again at the end
of uart_close().

[1] In fact, some input may actually be buffered _after_ stop_rx()
since the rx interrupt may have already triggered but not yet been
handled when stop_rx() disables rx interrupts.

Fixes: 2e758910 ("serial: core: Flush ldisc after dropping port
mutex in uart_close()")
Reported-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 068500e0.

According to some tests, SDMA support is broken at least for i.MX6 without
HW flow control. Different forms of data-corruption appear either with
the ROM firmware for the SDMA controller as well as when loading Freescale
provided SDMA firmware versions 1.1 or 3.1.
Signed-off-by: NDavid Jander <david@protonic.nl>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Calls to regmap_raw_read/write needed register rewrite in a
similar way as function calls to regmap_read/write already had.
This enables reading/writing the serial datastream to the device.
Signed-off-by: NBo Svangård <bo.svangard@embeddedart.se>
Signed-off-by: NJakub Kicinski <kubakici@wp.pl>
Signed-off-by: NJon Ringle <jringle@gridpoint.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When I2C=m and SPI=y or-ing them will produce =y while
what we need is the lower bound, i.e. =m.  Fortunately
SPI is a boolean so we need to handle only one special
case.
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NJakub Kicinski <kubakici@wp.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In probe, we use dev_id as array index of etraxfs_uart_ports and store the
index in port->line. So etraxfs_uart_ports[port->line] should be released
when unload the module.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Acked-by: NNiklas Cassel <nks@flawful.org>
Acked-by: NJesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If vc->vc_uni_pagedir_loc is not NULL, its refcount needs to be
decreased before vc_uni_pagedir_loc is re-assigned.

unreferenced object 0xffff88002cdd13b0 (size 512):
  comm "setfont", pid 503, jiffies 4294896503 (age 722.828s)
  hex dump (first 32 bytes):
    40 92 61 2b 00 88 ff ff 00 00 00 00 00 00 00 00  @.a+............
    00 00 00 00 00 00 00 00 a0 ad 61 2b 00 88 ff ff  ..........a+....
  backtrace:
    [<ffffffff817b755e>] kmemleak_alloc+0x4e/0xb0
    [<ffffffff811d4898>] kmem_cache_alloc_trace+0x1c8/0x240
    [<ffffffff814ae7d3>] con_do_clear_unimap.isra.2+0x83/0xe0
    [<ffffffff814ae9b2>] con_clear_unimap+0x22/0x40
    [<ffffffff814a8db8>] vt_ioctl+0xeb8/0x1170
    [<ffffffff8149b458>] tty_ioctl+0x208/0xca0
    [<ffffffff81207858>] do_vfs_ioctl+0x2f8/0x510
    [<ffffffff81207af1>] SyS_ioctl+0x81/0xa0
    [<ffffffff817ca2b2>] system_call_fastpath+0x16/0x75
    [<ffffffffffffffff>] 0xffffffffffffffff
unreferenced object 0xffff88002b619240 (size 256):
  comm "setfont", pid 503, jiffies 4294896503 (age 722.828s)
  hex dump (first 32 bytes):
    90 bc 84 d5 00 88 ff ff 58 85 84 d5 00 88 ff ff  ........X.......
    88 ac 84 d5 00 88 ff ff e0 b1 84 d5 00 88 ff ff  ................
  backtrace:
    [<ffffffff817b755e>] kmemleak_alloc+0x4e/0xb0
    [<ffffffff811d4898>] kmem_cache_alloc_trace+0x1c8/0x240
    [<ffffffff814ae286>] con_insert_unipair+0x86/0x170
    [<ffffffff814af107>] con_set_unimap+0x1b7/0x280
    [<ffffffff814a8d65>] vt_ioctl+0xe65/0x1170
    [<ffffffff8149b458>] tty_ioctl+0x208/0xca0
    [<ffffffff81207858>] do_vfs_ioctl+0x2f8/0x510
    [<ffffffff81207af1>] SyS_ioctl+0x81/0xa0
    [<ffffffff817ca2b2>] system_call_fastpath+0x16/0x75
    [<ffffffffffffffff>] 0xffffffffffffffff
Signed-off-by: NDongxing Zhang <dongxing.zhang@intel.com>
Signed-off-by: NXiaoming Wang <xiaoming.wang@intel.com>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Tested-by: NKonstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Value returned by devm_ioremap_resource() was checked for non-NULL but
devm_ioremap_resource() returns IOMEM_ERR_PTR, not NULL. In case of
error this could lead to dereference of ERR_PTR.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski.k@gmail.com>
Cc: <stable@vger.kernel.org>
Fixes: 3873e2d7 ("drivers: PL011: refactor pl011_probe()")
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When handling signalling char, claim the termios write lock before
signalling waiting readers and writers to prevent further i/o
before flushing the echo and output buffers. This prevents a
userspace signal handler which may output from racing the terminal
flush.

Reference: Bugzilla #99351 ("Output truncated in ssh session after...")
Fixes: commit d2b6f447 ("n_tty: Fix signal handling flushes")
Reported-by: NFilipe Brandenburger <filbranden@google.com>
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>