The 10.x firmware does not support IBSS mode at
all. It can't beacon and it crashes when trying to
scan.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Firmware doesn't perform Rx reordering so it is
left to the host driver to do that.

Use mac80211 to perform reordering instead of
re-inventing the wheel.

This fixes TCP throughput issues in some
environments.
Reported-by: NDenton Gentry <denton.gentry@gmail.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Apparently fw/hw generates a corrupted QoS Control
Field in Qos NullFunc frames. The only way to
workaround this is to downgrade frames to
NullFunc. This should be okay since powersave is
done by fw/hw and these frames are only used for
CQM purposes (e.g. from hostapd to check if
station is still connected).

This doesn't fix any user visible bug that I know
of. It just prevents from sending out funky frames
on the air.
Reported-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It always bugged me how tid is computed and stored
in a temporary var before written to the control
buffer. It was confusing and it made it difficult
to work with tx helpers.

While at it rename the qos workaround function as
it was misleading - it's not a workaround but
preparation for nwifi tx mode.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Some drivers (such as iwlmvm) can handle multiple bands in a single
HW scan request. Add a HW flag to indicate that the driver support
this. To hold the required data, create a separate structure for
HW scan request that holds cfg scan request and data about
different parts of the scan IEs.

As this changes the mac80211 API, update all drivers using it to
use the correct new function type/argument.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

FW creates self-peer for AP internally.

This prevents ath10k from trying to create
explicit self-peer during hw recovery and thus
prevents a timeout and a warning during teardown:

  ath10k: removing stale peer $AP_BSSID from vdev_id 0
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

All configuration sequences should be protected
with conf_mutex to avoid concurrent/conflicting
requests.

This should make sure that wep tx key setup is not
performed while hw is restarted (at least).
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This makes sure no further tx requests are
submitted to HTT before driver teardown.

This should prevent invalid pointer/NULL
dereference on htt tx pool in ath10k_htt_tx() in
some cases of heavy traffic.

kvalo: remove the WARN_ON() if conf_mutex is held
Reported-By: NBen Greear <greearb@candelatech.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This reduces risk of races and prepares for more
hw restart fixes.

It also makes sense to perform teardown after
mac80211 starts its restart routine as it
guarantees it has stopped itself by then
(including tx queues).
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This fixes failpath when override AC pdev param
setup fails and makes other pdev params setting
fail as well.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The channel_switch_beacon callback is optional, so it doesn't have to
be defined if it's not going to do anything useful with it.  Both
ath9k and ath10k define the callback and just returns.  This commit
removes them.

Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Verified that target's tx/rx chain register is set appropriately,
and that the tx rate goes down as number of chains
decrease, but I did not actually try to verify antenna
ceased to transmit when disabled.

kvalo: move ar->supp_*_chainmask initialisation to ath10k_mac_register()
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NAvery Pennarun <apenwarr@gmail.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fix sending and receiveing protected managment frames.
Lack of protected flag for received protected action frames
causes report these frames as unprotected robust action frames.
If the driver in AP mode sent frame with protected flag and
CCMP header using IEEE80211_KEY_FLAG_SW_MGMT_TX flag,
the FW encrypted frames once again. From user side all
received SA Query Requests and Responses were skipped and
all protected action frames were sent as malformed packets.
Signed-off-by: NMarek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Beacon data wasn't properly cleared during early
phase of recovery. This in turn caused firmware to
crash because the beacon data was submitted before
vdevs were fully re-configured. Ultimately the
device was considered wedged and nothing worked
until driver was reloaded.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

If for some reason mac80211 wouldn't stop
beaconing gracefully and just removed interface of
a running AP/IBSS interface it was possible to
leak pending beacon DMA mapping. It's very
unlikely but better safe than sorry.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

If 20MHz CAC completed successfully then
subsequent CAC with wider bandwidth (40Mhz, 80Mhz)
with identical control frequency did not start
monitor vdev making it impossible to detect any
radar pulses during intended CAC.

It also was incorrect to assume ath10k_config() will
be called after CAC is finished. Theoretically for
non-HT channels nothing changes between CAC and
start_ap() (albeit in practice this can be
different). The incorrect assumption led to CAC
not being stopped on non-HT chandefs leading to
all Rx being drooped making it impossible for
clients to associate.

While at it clean up the code a bit.

kvalo: separate WARN_ON() from the if statement
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This is done to avoid forward declarations with
upcomming patches.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This will allow the low level driver to make decision based
on the vif such as queues etc...
Since the vif might be NULL, we can't add it to the tracing
functions.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
[fix staging rtl8821ae driver]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

It was possible to create/delete/start/stop
monitor vdev from a few places that were not
exclusively protected against each other. This
resulted in monitor vdev being stopped/removed by
one call origin while another one was expecting it
to continue running.

For example if CAC was started and interface's
promiscuous mode was toggled monitor vdev was
removed from the driver meaning no radar would be
detected. In additional a warning would be printed
upon CAC completion complaining it tried to stop
non-running monitor vdev.

The patch simplifies monitor code by removing
IEEE80211_HW_WANT_MONITOR_VIF (which wasn't really
ever needed) and improves state tracking. It also
unifies prints.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Currently there are different styles used for warning messages, unify them to
look similar. The style basically is:

1) start with a verb (if possible)

2) lower case letters

3) use plain english as much as possible
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Regulatory domain settings for firmware 10.x has more options
than main firmware, so handle regulatory domain setup separately
for both supported firmwares. Fill in additional dfs domain
parameter according to current regulatory.
This patch does not solve any known bug. Not handled parameter
for firmware 10.x was found during code review.
Signed-off-by: NMarek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add recalculation of RTS/CTS protection when one or more legacy
stations are connected to ath10k. In this case enable RTS/CTS
protection and set sw retry profile are needed in the FW.
Without this change legacy station is starved and has very low
throughput.
Signed-off-by: NMarek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

IBSS mode requires the changing of supported rate. Do this
by reassociate the peer. The investigation shows that if move
from legacy to HT, the rate control won't work after changing
the supported rate. But once changing the supported rate to HT,
user can assign the TxRate in HT mode.
Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

When using multiple vdevs (stations, aps, etc), it is
nice to be able to associate log messages with specific
interfaces.  So, add vdev-id to most logging messages.
Add return code as well, where it was missing.

kvalo: unify some of the messages to follow the same style
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

There's no real benefit from using them. DMA-API
already provides debugging. Some skbuffs are
already mapped directly with DMA-API since wrapper
arguments were insufficient and extending them
would be pointless.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add force SGI support.
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Indicate spectrum management support in hardware
flags, while we already handle power set
(IEEE80211_CONF_CHANGE_POWER) in the ath10k driver.
This enable 802.11h support for station mode.
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The arsta structure wasn't initialized for
non-ap interfaces. This should fix related
warnings/crashes.
Reported-By: NBen Greear <greearb@candelatech.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Makes it easier to determine why some failures
happened.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Implement the get TSF by simply returning 0 so that IBSS
merging is happening. Otherwise, IBSS nodes that have similar
SSID naming won't merge. This is simply fooling the mac80211
that the TSF in the received beacon is higher than the local TSF.
Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This allows dynamic changes of bandwidth/nss/smps,
e.g. via ht/vht operation mode change
notification.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Firmware ignores SMPS flags in peer assoc command.

For SMPS to work it is necessary to set peer
parameter after peer assoc command so that tx
chainmask is setup properly.

This should fix packet loss and improve throughput
with stations that have SMPS enabled upon
association.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

I modified Michal's commit c930f744 ("ath10k: implement channel switching") to return
when vdev_start() fails, but forgot to release conf_mutex.

Found by coccinelle:

>> drivers/net/wireless/ath/ath10k/mac.c:2745:5-11: preceding lock on line 2663
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fixes a checkpatch warning in ath10k:

drivers/net/wireless/ath/ath10k/mac.c:1636: WARNING: Avoid CamelCase: <regpair->regDmnEnum>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This is a workaround for HT-enabled STAs which break the spec
and have no HT capabilities RX mask (no HT RX MCS map).

As per spec, in section 20.3.5 Modulation and coding scheme (MCS),
MCS 0 through 7 are mandatory in 20MHz with 800 ns GI at all STAs.

Firmware asserts if such situation occurs.
Signed-off-by: NBartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In case of warm reset target need to be suspended.
Suspend function is extented to handle both cases
with disabling interrupts and without disabling interrupts.
Warm target reset requires suspend with all interrupts
disabled.

This patch depends on
ath10k: fix device initialization routine
Signed-off-by: NMarek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Suspend/resume callbacks are not protected by configuration mutex
so adding such protection. Also in order to simplify implemetation
of suspend function wait queue is replaced by completion.
Signed-off-by: NMarek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It was found during testing the nss calculation does not
cover all corner cases. Station could request eq. only MCS8
and MCS9 (nss=2 specific). Next num_rates=2 so the driver
sets nss=(max((2+7)/8, 1))=1. Which is wrong. The in-driver
calculation was introduced prior (commit ddcc347b
mac80211: fix rx_nss calculation for drivers with hw rc).
Since it's fixed, use mac80211 provided value from now.
End user will experience lower throuhputs than expected
if the nss is wrongly calculated.
Signed-off-by: NMarek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

ARP frames exchange does not work properly for UAPSD enabled AP.
ARP requests which arrives with access category 0 are processed
by network stack and send back with access category 0. FW changes
access category to 6. This is causing problems when UAPSD associated
STA is sleeping after has sent ARP request. Configure ARP access
category in FW to best effort (0) solves this problem. ARP frames
will be send with access category 0.

Simplify arp ac override functionality by removing redundant entry in
pdev param maping table. There should be only one entry in pdev param
map but enum has different name for different FW.

kvalo: change the warning message
Signed-off-by: NMarek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

If recovery failed ath10k returned 0 (success) and
mac80211 continued to call other driver callbacks.
This caused null dereference.

This is how the failure looked like:

ath10k: ctl_resp never came in (-110)
ath10k: failed to connect to HTC: -110
ath10k: could not init core (-110)
BUG: unable to handle kernel NULL pointer dereference at           (null)
IP: [<ffffffffa0b355c1>] ath10k_ce_send+0x1d/0x15d [ath10k_pci]
PGD 0
Oops: 0000 [#1] PREEMPT SMP
Modules linked in: ath10k_pci ath10k_core ath5k ath9k ath9k_common ath9k_hw ath mac80211 cfg80211 nf_nat_ipv4 ]
CPU: 1 PID: 36 Comm: kworker/1:1 Tainted: G        WC   3.13.0-rc8-wl-ath+ #8
Hardware name: To be filled by O.E.M. To be filled by O.E.M./HURONRIVER, BIOS 4.6.5 05/02/2012
Workqueue: events ieee80211_restart_work [mac80211]
task: ffff880215b521c0 ti: ffff880215e18000 task.ti: ffff880215e18000
RIP: 0010:[<ffffffffa0b355c1>]  [<ffffffffa0b355c1>] ath10k_ce_send+0x1d/0x15d [ath10k_pci]
RSP: 0018:ffff880215e19af8  EFLAGS: 00010292
RAX: ffff880215e19b10 RBX: 0000000000000000 RCX: 0000000000000018
RDX: 00000000d9ccf800 RSI: ffff8800c965ad00 RDI: 0000000000000000
RBP: ffff880215e19b58 R08: 0000000000000002 R09: 0000000000000000
R10: ffffffff812e1a23 R11: 0000000000000292 R12: 0000000000000018
R13: 0000000000000000 R14: 0000000000000002 R15: ffff88021562d700
FS:  0000000000000000(0000) GS:ffff88021fa80000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 0000000001a0d000 CR4: 00000000000407e0
Stack:
 d9ccf8000d47df40 ffffffffa0b367a0 ffff880215e19b10 0000000000000010
 ffff880215e19b68 ffff880215e19b28 0000000000000018 ffff8800c965ad00
 0000000000000018 0000000000000000 0000000000000002 ffff88021562d700
Call Trace:
 [<ffffffffa0b3251d>] ath10k_pci_hif_send_head+0xa7/0xcb [ath10k_pci]
 [<ffffffffa0b16cbe>] ath10k_htc_send+0x23d/0x2d0 [ath10k_core]
 [<ffffffffa0b1a169>] ath10k_wmi_cmd_send_nowait+0x5d/0x85 [ath10k_core]
 [<ffffffffa0b1aaef>] ath10k_wmi_cmd_send+0x62/0x115 [ath10k_core]
 [<ffffffff814e8abd>] ? __netdev_alloc_skb+0x4b/0x9b
 [<ffffffffa0b1c438>] ath10k_wmi_vdev_set_param+0x91/0xa3 [ath10k_core]
 [<ffffffffa0b0e0d5>] ath10k_mac_set_rts+0x3e/0x40 [ath10k_core]
 [<ffffffffa0b0e1d0>] ath10k_set_frag_threshold+0x5e/0x9c [ath10k_core]
 [<ffffffffa09d60eb>] ieee80211_reconfig+0x12a/0x7b3 [mac80211]
 [<ffffffff815a8069>] ? mutex_unlock+0x9/0xb
 [<ffffffffa09b3a40>] ieee80211_restart_work+0x5e/0x68 [mac80211]
 [<ffffffff810c01d0>] process_one_work+0x1d7/0x2fc
 [<ffffffff810c0166>] ? process_one_work+0x16d/0x2fc
 [<ffffffff810c06c8>] worker_thread+0x12e/0x1fb
 [<ffffffff810c059a>] ? rescuer_thread+0x27b/0x27b
 [<ffffffff810c5aee>] kthread+0xb5/0xbd
 [<ffffffff815a9220>] ? _raw_spin_unlock_irq+0x28/0x42
 [<ffffffff810c5a39>] ? __kthread_parkme+0x5c/0x5c
 [<ffffffff815ae04c>] ret_from_fork+0x7c/0xb0
 [<ffffffff810c5a39>] ? __kthread_parkme+0x5c/0x5c
Code: df ff d0 48 83 c4 18 5b 41 5c 41 5d 5d c3 55 48 89 e5 41 57 41 56 45 89 c6 41 55 41 54 41 89 cc 53 48 89
RIP  [<ffffffffa0b355c1>] ath10k_ce_send+0x1d/0x15d [ath10k_pci]
 RSP <ffff880215e19af8>
CR2: 0000000000000000
Reported-By: NBen Greear <greearb@candelatech.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>