A display resolution is only supported if it meets all the restrictions
below for Maximum Pipe Pixel Rate.

The display resolution must fit within the maximum pixel rate output
from the pipe. Make sure that the display pipe is able to feed pixels at
a rate required to support the desired resolution.
For each enabled plane on the pipe {
    If plane scaling enabled {
	Horizontal down scale amount = Maximum[1, plane horizontal size /
		    scaler horizontal window size]
	Vertical down scale amount = Maximum[1, plane vertical size /
		    scaler vertical window size]
	Plane down scale amount = Horizontal down scale amount *
		    Vertical down scale amount
	Plane Ratio = 1 / Plane down scale amount
    }
    Else {
	Plane Ratio = 1
    }
    If plane source pixel format is 64 bits per pixel {
	Plane Ratio = Plane Ratio * 8/9
    }
}

Pipe Ratio = Minimum Plane Ratio of all enabled planes on the pipe

If pipe scaling is enabled {
    Horizontal down scale amount = Maximum[1, pipe horizontal source size /
		scaler horizontal window size]
    Vertical down scale amount = Maximum[1, pipe vertical source size /
		scaler vertical window size]
    Note: The progressive fetch - interlace display mode is equivalent to a
		2.0 vertical down scale
    Pipe down scale amount = Horizontal down scale amount *
		Vertical down scale amount
    Pipe Ratio = Pipe Ratio / Pipe down scale amount
}

Pipe maximum pixel rate = CDCLK frequency * Pipe Ratio

In this patch our calculation is based on pipe downscale amount
(plane max downscale amount * pipe downscale amount) instead of Pipe
Ratio. So,
max supported crtc clock with given scaling = CDCLK / pipe downscale.
Flip will fail if,
current crtc clock > max supported crct clock with given scaling.

Changes since V1:
 - separate out fixed_16_16 wrapper API definition
Changes since V2:
 - Fix buggy crtc !active condition (Maarten)
 - use intel_wm_plane_visible wrapper as per Maarten's suggestion
Changes since V3:
 - Change failure return from ERANGE to EINVAL
Changes since V4:
 - Rebase based on previous patch changes
Changes since V5:
 - return EINVAL instead of continue (Maarten)
Changes since V6:
 - Improve commit message
 - Address review comment
Changes since V7:
 - use !enable instead of !active
 - rename config variable for consistency (Maarten)
Signed-off-by: NMahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170526151546.25025-4-mahesh1.kumar@intel.com

This patch implements new DDB allocation algorithm as per HW team
recommendation. This algo takecare of scenario where we allocate less DDB
for the planes with lower relative pixel rate, but they require more DDB
to work.
It also takes care of enabling same watermark level for each
plane in crtc, for efficient power saving.

Changes since v1:
 - Rebase on top of Paulo's patch series

Changes since v2:
 - Fix the for loop condition to enable WM

Changes since v3:
 - Fix crash in cursor i-g-t reported by Maarten
 - Rebase after addressing Paulo's comments
 - Few other ULT fixes
Changes since v4:
 - Rebase on drm-tip
 - Added separate function to enable WM levels
Changes since v5:
 - Fix a crash identified in skl-6770HQ system
Changes since v6:
 - Address review comments from Matt
Changes since v7:
 - Fix failure return in skl_compute_plane_wm (Matt)
 - fix typo
Changes since v8:
 - Always check cursor wm enable irrespective of total_data_rate
Changes since v9:
 - fix typo
Signed-off-by: NMahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170601055918.4601-1-mahesh1.kumar@intel.com

On some systems there can be a race condition in which no crtc state is
added to the first atomic commit. This results in all crtc's having a
null DDB allocation, causing a FIFO underrun on any update until the
first modeset.

Changes since v1:
- Do not take the connection_mutex, this is already done below.
Reported-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Inspired-by: NMahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: 98d39494 ("drm/i915/gen9: Compute DDB allocation at atomic
check time (v4)")
Cc: <stable@vger.kernel.org> # v4.8+
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170531154236.27180-1-maarten.lankhorst@linux.intel.comReviewed-by: NMahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>

Since

commit bac2a909
Author: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Date:   Wed Jan 21 02:17:42 2015 +0100

    PCI / PM: Avoid resuming PCI devices during system suspend

PCI devices will default to allowing the system suspend complete
optimization where devices are not woken up during system suspend if
they were already runtime suspended. This however breaks the i915/HDA
drivers for two reasons:

- The i915 driver has system suspend specific steps that it needs to
  run, that bring the device to a different state than its runtime
  suspended state.

- The HDA driver's suspend handler requires power that it will request
  from the i915 driver's power domain handler. This in turn requires the
  i915 driver to runtime resume itself, but this won't be possible if the
  suspend complete optimization is in effect: in this case the i915
  runtime PM is disabled and trying to get an RPM reference returns
  -EACCESS.

Solve this by requiring the PCI/PM core to resume the device during
system suspend which in effect disables the suspend complete optimization.

Regardless of the above commit the optimization stayed disabled for DRM
devices until

commit d14d2a84
Author: Lukas Wunner <lukas@wunner.de>
Date:   Wed Jun 8 12:49:29 2016 +0200

    drm: Remove dev_pm_ops from drm_class

so this patch is in practice a fix for this commit. Another reason for
the bug staying hidden for so long is that the optimization for a device
is disabled if it's disabled for any of its children devices. i915 may
have a backlight device as its child which doesn't support runtime PM
and so doesn't allow the optimization either.  So if this backlight
device got registered the bug stayed hidden.

Credits to Marta, Tomi and David who enabled pstore logging,
that caught one instance of this issue across a suspend/
resume-to-ram and Ville who rememberd that the optimization was enabled
for some devices at one point.

The first WARN triggered by the problem:

[ 6250.746445] WARNING: CPU: 2 PID: 17384 at drivers/gpu/drm/i915/intel_runtime_pm.c:2846 intel_runtime_pm_get+0x6b/0xd0 [i915]
[ 6250.746448] pm_runtime_get_sync() failed: -13
[ 6250.746451] Modules linked in: snd_hda_intel i915 vgem snd_hda_codec_hdmi x86_pkg_temp_thermal intel_powerclamp coretemp crct10dif_pclmul crc32_pclmul
snd_hda_codec_realtek snd_hda_codec_generic ghash_clmulni_intel e1000e snd_hda_codec snd_hwdep snd_hda_core ptp mei_me pps_core snd_pcm lpc_ich mei prime_
numbers i2c_hid i2c_designware_platform i2c_designware_core [last unloaded: i915]
[ 6250.746512] CPU: 2 PID: 17384 Comm: kworker/u8:0 Tainted: G     U  W       4.11.0-rc5-CI-CI_DRM_334+ #1
[ 6250.746515] Hardware name:                  /NUC5i5RYB, BIOS RYBDWi35.86A.0362.2017.0118.0940 01/18/2017
[ 6250.746521] Workqueue: events_unbound async_run_entry_fn
[ 6250.746525] Call Trace:
[ 6250.746530]  dump_stack+0x67/0x92
[ 6250.746536]  __warn+0xc6/0xe0
[ 6250.746542]  ? pci_restore_standard_config+0x40/0x40
[ 6250.746546]  warn_slowpath_fmt+0x46/0x50
[ 6250.746553]  ? __pm_runtime_resume+0x56/0x80
[ 6250.746584]  intel_runtime_pm_get+0x6b/0xd0 [i915]
[ 6250.746610]  intel_display_power_get+0x1b/0x40 [i915]
[ 6250.746646]  i915_audio_component_get_power+0x15/0x20 [i915]
[ 6250.746654]  snd_hdac_display_power+0xc8/0x110 [snd_hda_core]
[ 6250.746661]  azx_runtime_resume+0x218/0x280 [snd_hda_intel]
[ 6250.746667]  pci_pm_runtime_resume+0x76/0xa0
[ 6250.746672]  __rpm_callback+0xb4/0x1f0
[ 6250.746677]  ? pci_restore_standard_config+0x40/0x40
[ 6250.746682]  rpm_callback+0x1f/0x80
[ 6250.746686]  ? pci_restore_standard_config+0x40/0x40
[ 6250.746690]  rpm_resume+0x4ba/0x740
[ 6250.746698]  __pm_runtime_resume+0x49/0x80
[ 6250.746703]  pci_pm_suspend+0x57/0x140
[ 6250.746709]  dpm_run_callback+0x6f/0x330
[ 6250.746713]  ? pci_pm_freeze+0xe0/0xe0
[ 6250.746718]  __device_suspend+0xf9/0x370
[ 6250.746724]  ? dpm_watchdog_set+0x60/0x60
[ 6250.746730]  async_suspend+0x1a/0x90
[ 6250.746735]  async_run_entry_fn+0x34/0x160
[ 6250.746741]  process_one_work+0x1f2/0x6d0
[ 6250.746749]  worker_thread+0x49/0x4a0
[ 6250.746755]  kthread+0x107/0x140
[ 6250.746759]  ? process_one_work+0x6d0/0x6d0
[ 6250.746763]  ? kthread_create_on_node+0x40/0x40
[ 6250.746768]  ret_from_fork+0x2e/0x40
[ 6250.746778] ---[ end trace 102a62fd2160f5e6 ]---

v2:
- Use the new pci_dev->needs_resume flag, to avoid any overhead during
  the ->pm_prepare hook. (Rafael)

v3:
- Update commit message to reference the actual regressing commit.
  (Lukas)

v4:
- Rebase on v4 of patch 1/2.

Fixes: d14d2a84 ("drm: Remove dev_pm_ops from drm_class")
References: https://bugs.freedesktop.org/show_bug.cgi?id=100378
References: https://bugs.freedesktop.org/show_bug.cgi?id=100770
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Marta Lofstedt <marta.lofstedt@intel.com>
Cc: David Weinehall <david.weinehall@linux.intel.com>
Cc: Tomi Sarvela <tomi.p.sarvela@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: linux-pci@vger.kernel.org
Cc: <stable@vger.kernel.org> # v4.10.x: 4d071c32 - PCI/PM: Add needs_resume flag
Cc: <stable@vger.kernel.org> # v4.10.x
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Reported-and-tested-by: NMarta Lofstedt <marta.lofstedt@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1493726649-32094-2-git-send-email-imre.deak@intel.com

We are passing parameters in the wrong order to find next zero bit, and
when it doesn't find anything it returns size (offset in the code), which
is always zero.

For reference the function is defined as:
find_next_bit( *addr, size, offset )

The incorrect parameter order was added by commit abddffdf
("drm/i915/guc: Sanitize GuC client initialization"). Luckily, currently
we only use a single guc client and a single doorbell, which happens to be
zero; therefore it isn't necessary to backport this fix (which would be for
v4.12).

Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: NMichel Thierry <michel.thierry@intel.com>
Reviewed-by: NDaniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170531000546.30762-1-michel.thierry@intel.com

psr1 is also disabled for panel resolution  greater than 32X20.
Added psr2 check to disable only for psr2 panels having resolution
greater than 32X20.

issue was introduced by
commit-id : "acf45d11"
commit message: "PSR2 is restricted to work with panel resolutions
upto 3200x2000, move the check to intel_psr_match_conditions and fully
block psr."

v2: (Rodrigo)
   Add previous commit details which introduced the issue

Fixes: acf45d11 ("drm/i915/psr: disable psr2 for resolution greater than 32X20")
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jim Bride <jim.bride@linux.intel.com>
Cc: Yaroslav Shabalin <yaroslav.shabalin@gmail.com>
Reported-by: NYaroslav Shabalin <yaroslav.shabalin@gmail.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Nvathsala nagaraju <vathsala.nagaraju@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/49935bdff896ee3140bed471012b9f9110a863a4.1495729964.git.vathsala.nagaraju@intel.com

Allow intel_engine_is_idle() to be called outside of the GT wakeref by
acquiring the device runtime pm for ourselves. This allows the function
to act as check after we assume the engine is idle and we release the GT
wakeref held whilst we have requests. At the moment, we do not call it
outside of an awake context but taking the wakeref as required makes it
more convenient to use for quick debugging in future.

[ 2613.401647] RPM wakelock ref not held during HW access
[ 2613.401684] ------------[ cut here ]------------
[ 2613.401720] WARNING: CPU: 5 PID: 7739 at drivers/gpu/drm/i915/intel_drv.h:1787 gen6_read32+0x21f/0x2b0 [i915]
[ 2613.401731] Modules linked in: snd_hda_intel i915 vgem snd_hda_codec_hdmi x86_pkg_temp_thermal intel_powerclamp snd_hda_codec_realtek coretemp snd_hda_codec_generic crct10dif_pclmul crc32_pclmul ghash_clmulni_intel snd_hda_codec snd_hwdep snd_hda_core snd_pcm r8169 mii mei_me lpc_ich mei prime_numbers [last unloaded: i915]
[ 2613.401823] CPU: 5 PID: 7739 Comm: drv_missed_irq Tainted: G     U          4.12.0-rc2-CI-CI_DRM_421+ #1
[ 2613.401825] Hardware name: MSI MS-7924/Z97M-G43(MS-7924), BIOS V1.12 02/15/2016
[ 2613.401840] task: ffff880409e3a740 task.stack: ffffc900084dc000
[ 2613.401861] RIP: 0010:gen6_read32+0x21f/0x2b0 [i915]
[ 2613.401863] RSP: 0018:ffffc900084dfce8 EFLAGS: 00010292
[ 2613.401869] RAX: 000000000000002a RBX: ffff8804016a8000 RCX: 0000000000000006
[ 2613.401871] RDX: 0000000000000006 RSI: ffffffff81cbf2d9 RDI: ffffffff81c9e3a7
[ 2613.401874] RBP: ffffc900084dfd18 R08: ffff880409e3afc8 R09: 0000000000000000
[ 2613.401877] R10: 000000008a1c483f R11: 0000000000000000 R12: 000000000000209c
[ 2613.401879] R13: 0000000000000001 R14: ffff8804016a8000 R15: ffff8804016ac150
[ 2613.401882] FS:  00007f39ef3dd8c0(0000) GS:ffff88041fb40000(0000) knlGS:0000000000000000
[ 2613.401885] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 2613.401887] CR2: 00000000023717c8 CR3: 00000002e7b34000 CR4: 00000000001406e0
[ 2613.401889] Call Trace:
[ 2613.401912]  intel_engine_is_idle+0x76/0x90 [i915]
[ 2613.401931]  i915_gem_wait_for_idle+0xe6/0x1e0 [i915]
[ 2613.401951]  fault_irq_set+0x40/0x90 [i915]
[ 2613.401970]  i915_ring_test_irq_set+0x42/0x50 [i915]
[ 2613.401976]  simple_attr_write+0xc7/0xe0
[ 2613.401981]  full_proxy_write+0x4f/0x70
[ 2613.401987]  __vfs_write+0x23/0x120
[ 2613.401992]  ? rcu_read_lock_sched_held+0x75/0x80
[ 2613.401996]  ? rcu_sync_lockdep_assert+0x2a/0x50
[ 2613.401999]  ? __sb_start_write+0xfa/0x1f0
[ 2613.402004]  vfs_write+0xc5/0x1d0
[ 2613.402008]  ? trace_hardirqs_on_caller+0xe7/0x1c0
[ 2613.402013]  SyS_write+0x44/0xb0
[ 2613.402020]  entry_SYSCALL_64_fastpath+0x1c/0xb1
[ 2613.402022] RIP: 0033:0x7f39eded6670
[ 2613.402025] RSP: 002b:00007fffdcdcb1a8 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
[ 2613.402030] RAX: ffffffffffffffda RBX: ffffffff81470203 RCX: 00007f39eded6670
[ 2613.402033] RDX: 0000000000000001 RSI: 000000000041bc33 RDI: 0000000000000006
[ 2613.402036] RBP: ffffc900084dff88 R08: 00007f39ef3dd8c0 R09: 0000000000000001
[ 2613.402038] R10: 0000000000000000 R11: 0000000000000246 R12: 000000000041bc33
[ 2613.402041] R13: 0000000000000006 R14: 0000000000000000 R15: 0000000000000000
[ 2613.402046]  ? __this_cpu_preempt_check+0x13/0x20
[ 2613.402052] Code: 01 9b fa e0 0f ff e9 28 fe ff ff 80 3d 6a dd 0e 00 00 0f 85 29 fe ff ff 48 c7 c7 48 19 29 a0 c6 05 56 dd 0e 00 01 e8 da 9a fa e0 <0f> ff e9 0f fe ff ff b9 01 00 00 00 ba 01 00 00 00 44 89 e6 48
[ 2613.402199] ---[ end trace 31f0cfa93ab632bf ]---

Fixes: 5400367a ("drm/i915: Ensure the engine is idle before manually changing HWS")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170530121334.17364-2-chris@chris-wilson.co.ukReviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>

If the device is asleep (no GT wakeref), we know the GPU is already idle.
If we add an early return, we can avoid touching registers and checking
hw state outside of the assumed GT wakelock. This prevents causing such
errors whilst debugging:

[ 2613.401647] RPM wakelock ref not held during HW access
[ 2613.401684] ------------[ cut here ]------------
[ 2613.401720] WARNING: CPU: 5 PID: 7739 at drivers/gpu/drm/i915/intel_drv.h:1787 gen6_read32+0x21f/0x2b0 [i915]
[ 2613.401731] Modules linked in: snd_hda_intel i915 vgem snd_hda_codec_hdmi x86_pkg_temp_thermal intel_powerclamp snd_hda_codec_realtek coretemp snd_hda_codec_generic crct10dif_pclmul crc32_pclmul ghash_clmulni_intel snd_hda_codec snd_hwdep snd_hda_core snd_pcm r8169 mii mei_me lpc_ich mei prime_numbers [last unloaded: i915]
[ 2613.401823] CPU: 5 PID: 7739 Comm: drv_missed_irq Tainted: G     U          4.12.0-rc2-CI-CI_DRM_421+ #1
[ 2613.401825] Hardware name: MSI MS-7924/Z97M-G43(MS-7924), BIOS V1.12 02/15/2016
[ 2613.401840] task: ffff880409e3a740 task.stack: ffffc900084dc000
[ 2613.401861] RIP: 0010:gen6_read32+0x21f/0x2b0 [i915]
[ 2613.401863] RSP: 0018:ffffc900084dfce8 EFLAGS: 00010292
[ 2613.401869] RAX: 000000000000002a RBX: ffff8804016a8000 RCX: 0000000000000006
[ 2613.401871] RDX: 0000000000000006 RSI: ffffffff81cbf2d9 RDI: ffffffff81c9e3a7
[ 2613.401874] RBP: ffffc900084dfd18 R08: ffff880409e3afc8 R09: 0000000000000000
[ 2613.401877] R10: 000000008a1c483f R11: 0000000000000000 R12: 000000000000209c
[ 2613.401879] R13: 0000000000000001 R14: ffff8804016a8000 R15: ffff8804016ac150
[ 2613.401882] FS:  00007f39ef3dd8c0(0000) GS:ffff88041fb40000(0000) knlGS:0000000000000000
[ 2613.401885] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 2613.401887] CR2: 00000000023717c8 CR3: 00000002e7b34000 CR4: 00000000001406e0
[ 2613.401889] Call Trace:
[ 2613.401912]  intel_engine_is_idle+0x76/0x90 [i915]
[ 2613.401931]  i915_gem_wait_for_idle+0xe6/0x1e0 [i915]
[ 2613.401951]  fault_irq_set+0x40/0x90 [i915]
[ 2613.401970]  i915_ring_test_irq_set+0x42/0x50 [i915]
[ 2613.401976]  simple_attr_write+0xc7/0xe0
[ 2613.401981]  full_proxy_write+0x4f/0x70
[ 2613.401987]  __vfs_write+0x23/0x120
[ 2613.401992]  ? rcu_read_lock_sched_held+0x75/0x80
[ 2613.401996]  ? rcu_sync_lockdep_assert+0x2a/0x50
[ 2613.401999]  ? __sb_start_write+0xfa/0x1f0
[ 2613.402004]  vfs_write+0xc5/0x1d0
[ 2613.402008]  ? trace_hardirqs_on_caller+0xe7/0x1c0
[ 2613.402013]  SyS_write+0x44/0xb0
[ 2613.402020]  entry_SYSCALL_64_fastpath+0x1c/0xb1
[ 2613.402022] RIP: 0033:0x7f39eded6670
[ 2613.402025] RSP: 002b:00007fffdcdcb1a8 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
[ 2613.402030] RAX: ffffffffffffffda RBX: ffffffff81470203 RCX: 00007f39eded6670
[ 2613.402033] RDX: 0000000000000001 RSI: 000000000041bc33 RDI: 0000000000000006
[ 2613.402036] RBP: ffffc900084dff88 R08: 00007f39ef3dd8c0 R09: 0000000000000001
[ 2613.402038] R10: 0000000000000000 R11: 0000000000000246 R12: 000000000041bc33
[ 2613.402041] R13: 0000000000000006 R14: 0000000000000000 R15: 0000000000000000
[ 2613.402046]  ? __this_cpu_preempt_check+0x13/0x20
[ 2613.402052] Code: 01 9b fa e0 0f ff e9 28 fe ff ff 80 3d 6a dd 0e 00 00 0f 85 29 fe ff ff 48 c7 c7 48 19 29 a0 c6 05 56 dd 0e 00 01 e8 da 9a fa e0 <0f> ff e9 0f fe ff ff b9 01 00 00 00 ba 01 00 00 00 44 89 e6 48
[ 2613.402199] ---[ end trace 31f0cfa93ab632bf ]---

Fixes: 25112b64 ("drm/i915: Wait for all engines to be idle as part of i915_gem_wait_for_idle()")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170530121334.17364-1-chris@chris-wilson.co.ukReviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

Currently GVT-g cannot work properly when host GuC submission is
enabled, so make the driver loading failed in this case.

v2:
- use DRM_ERROR as it is a fatal message. (Chris)
Suggested-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChuanxiao Dong <chuanxiao.dong@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1495878259-7733-2-git-send-email-chuanxiao.dong@intel.com

GVT-g relies on the enable_execlists parameter in i915. If this option
is not enabled for GVT-g, should return -EIO to make i915 driver loading
failed.

v2:
- Use DMR_ERROR as it is a fatal message. (Chris)
Suggested-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: NChuanxiao Dong <chuanxiao.dong@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

The intel_gvt_sanitize_options will sanitize the GVT related
options before doing initialize the GVT.
Suggested-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: NChuanxiao Dong <chuanxiao.dong@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

I have a plan to write a quick test to exercise concurrent usage of
i915_gem_shrink(), the simplest way looks to be to have multiple threads
using debugfs/i915_drop_caches. However, we currently take one lock over
the entire function, serialising the calls into i915_gem_shrink() so
reduce the lock coverage.

Testcase: igt/gem_shrink/reclaim
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170524162653.5446-1-chris@chris-wilson.co.ukReviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

Add kerneldoc for the vma_list stored on the i915_gem_object, in
particular, documenting the expected ordering of elements -- i.e. that
we do expect GGTT VMA first followed by the ppGTT VMA.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170525204818.12044-1-chris@chris-wilson.co.ukReviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

SDVO was the last connector that's still using the legacy paths
for properties, and this is with a reason!

This connector implements a lot of properties dynamically,
and some of them shared with the digital connector state,
so sdvo_connector_state subclasses intel_digital_connector_state.

set_property had a lot of validation, but this is handled in the
drm core, so most of the validation can die off. The properties
are written right before enabling the connector, since there is no
good way to update the properties without crtc.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170501133804.8116-13-maarten.lankhorst@linux.intel.com

Do the same as other connectors, attempt to detect hdmi audio in
the detect() callback, and only use the force_audio property as
override. Compute has_audio in pipe_config, and use that value
instead of the probed value directly.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170501133804.8116-12-maarten.lankhorst@linux.intel.com

intel_hdmi supports 3 properties, force_audio, broadcast rgb and
scaling mode. The last one is only created for eDP, so the is_eDP
in set_property is not required.

panel fitting and broadcast rgb are straightforward and only requires
changing compute_config.

force_audio is also used to force DVI mode, which means changes to
compute_config and mode_valid. mode_valid is called with
connection_mutex held, so it can safely dereference connector->state.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170501133804.8116-11-maarten.lankhorst@linux.intel.com

intel_dp supports 3 properties, scaling mode, broadcast rgb and
force_audio. intel_digital_connector handles the plumbing,
so we only have to hook this up in compute_config and init.

Changes since v1:
- Remove limited_color_range too, unused. (danvet)
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170501133804.8116-10-maarten.lankhorst@linux.intel.com

Always detect if audio is available during edid detection.
With less magic switching it's easier to convert the dp connector
properties to atomic.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170501133804.8116-9-maarten.lankhorst@linux.intel.com

Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170501133804.8116-8-maarten.lankhorst@linux.intel.com

Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170501133804.8116-7-maarten.lankhorst@linux.intel.com

Some atomic properties are common between the various kinds of
connectors, for example a lot of them use panel fitting mode.
It makes sense to put a lot of it in a common place, so each
connector can use it while they're being converted.

Implement the properties required for the connectors:
- scaling mode property
- force audio property
- broadcast rgb
- aspect ratio

While at it, make clear that intel_digital_connector_atomic_get_property
is a hack that has to be removed when all connector properties
are converted to atomic.

Changes since v1:
- Scaling mode and aspect ratio are partly handled in core now.
Changes since v2:
- Split out the scaling mode / aspect ratio changes to a preparation
  patch.
- Use mode_changed for panel fitter, changes to this property
  are checked by fastset.
- Allowed_scaling_modes is removed, handled through core now.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170501133804.8116-6-maarten.lankhorst@linux.intel.com

None of the intel connectors can use all types of scaling modes,
so only try the ones that are possible. This is another preparation
for connectors towards conversion to atomic.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170501133804.8116-5-maarten.lankhorst@linux.intel.com
[mlankhorst: Use renamed drm_connector_attach_scaling_mode_property function]

The first step in converting connector properties to atomic is
wiring up the atomic state. We're still not completely supoprting
the scaling mode in the atomic case, but this is the first step
towards it.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170501133804.8116-4-maarten.lankhorst@linux.intel.com

This is a follow-up patch to the previous patch ([PATCH[1/2] drm/i915:
Disable decoupled MMIO) to remove the dead code for decoupled MMIO
implementation, as it won't be used any longer on GEN9LP.

Therefore, this patch reverts:

commit 85ee17eb
Author: Praveen Paneri <praveen.paneri@intel.com>
Date:   Tue Nov 15 22:49:20 2016 +0530

    drm/i915/bxt: Broxton decoupled MMIO
Signed-off-by: NKai Chen <kai.chen@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170523215812.18328-3-kai.chen@intel.com

The decoupled MMIO feature doesn't work as intended by HW team. Enabling
it with forcewake will only make debugging efforts more difficult, so
let's disable it.

Fixes: 85ee17eb ("drm/i915/bxt: Broxton decoupled MMIO")
Cc: Zhe Wang <zhe1.wang@intel.com>
Cc: Praveen Paneri <praveen.paneri@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v4.10+
Signed-off-by: NKai Chen <kai.chen@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170523215812.18328-2-kai.chen@intel.com

Linux 4.12-rc3

Daniel has requested this for some drm-intel-next work.

More stuff for 4.13:

- skl+ wm fixes from Mahesh Kumar
- some refactor and tests for i915_sw_fence (Chris)
- tune execlist/scheduler code (Chris)
- g4x,g33 gpu reset improvements (Chris, Mika)
- guc code cleanup (Michal Wajdeczko, Michał Winiarski)
- dp aux backlight improvements (Puthikorn Voravootivat)
- buffer based guc/host communication (Michal Wajdeczko)

* tag 'drm-intel-next-2017-05-29' of git://anongit.freedesktop.org/git/drm-intel: (253 commits)
  drm/i915: Update DRIVER_DATE to 20170529
  drm/i915: Keep the forcewake timer alive for 1ms past the most recent use
  drm/i915/guc: capture GuC logs if FW fails to load
  drm/i915/guc: Introduce buffer based cmd transport
  drm/i915/guc: Disable send function on fini
  drm: Add definition for eDP backlight frequency
  drm/i915: Drop AUX backlight enable check for backlight control
  drm/i915: Consolidate #ifdef CONFIG_INTEL_IOMMU
  drm/i915: Only GGTT vma may be pinned and prevent shrinking
  drm/i915: Serialize GTT/Aperture accesses on BXT
  drm/i915: Convert i915_gem_object_ops->flags values to use BIT()
  drm/i915/selftests: Silence compiler warning in igt_ctx_exec
  drm/i915/guc: Skip port assign on first iteration of GuC dequeue
  drm/i915: Remove misleading comment in request_alloc
  drm/i915/g33: Improve reset reliability
  Revert "drm/i915: Restore lost "Initialized i915" welcome message"
  drm/i915/huc: Update GLK HuC version
  drm/i915: Check for allocation failure
  drm/i915/guc: Remove action status and statistics from debugfs
  drm/i915/g4x: Improve gpu reset reliability
  ...

Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Pull thermal SoC management fixes from Eduardo Valentin:

 - fixes to TI SoC driver, Broadcom, qoriq

 - small sparse warning fix on thermal core

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
  thermal: broadcom: ns-thermal: default on iProc SoCs
  ti-soc-thermal: Fix a typo in a comment line
  ti-soc-thermal: Delete error messages for failed memory allocations in ti_bandgap_build()
  ti-soc-thermal: Use devm_kcalloc() in ti_bandgap_build()
  thermal: core: make thermal_emergency_poweroff static
  thermal: qoriq: remove useless call for of_thermal_get_trip_points()

UAPI Changes:
- Add DRM_MODE_ROTATE_ and DRM_MODE_REFLECT_ defines to the UAPI (Robert)

Cross-subsystem Changes:
- Standardize sync_file.txt documentation format (Mauro)

Core Changes:
- Turf drm_[cm]alloc functions for kvmalloc alternatives (Michal)
- Add optional mode_valid() hook to crtc/encoder/bridge (Jose)
- Improve documentation around mode validation/alteration (Daniel)
- Reduce sync_file construction time by deferring name creation (Chris)

Driver Changes:
- pl111: Wire up the clock divider and add debugfs (Eric)
- various: Fix include notation and remove -Iinclude/drm (Masahiro)
- stm: Add Benjamin Gaignard and Vincent Abriou as STM maintainers (Vincent)
- various: Miscellaneous trivial fixes to pl111/stm/vgem/vc4

Cc: Michal Hocko <mhocko@suse.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Robert Foss <robert.foss@collabora.com>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Jose Abreu <Jose.Abreu@synopsys.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>

* tag 'drm-misc-next-2017-05-26' of git://anongit.freedesktop.org/git/drm-misc: (55 commits)
  dma-buf/sync-file: Defer creation of sync_file->name
  sync_file.txt: standardize document format
  gpu: drm: gma500: remove two more dead variable
  drm/doc: Clarify mode_fixup vs. atomic_check a bit more
  drm/doc: Document adjusted/request modes a bit better
  drm: Add crtc/encoder/bridge->mode_valid() callbacks
  MAINTAINERS: update drm/stm maintainers list
  drm/stm: ltdc: fix duplicated arguments
  drm/pl111: Fix return value check in pl111_amba_probe()
  drm/amd: include <linux/delay.h> instead of "linux/delay.h"
  drm: Add DRM_MODE_ROTATE_ and DRM_MODE_REFLECT_ to UAPI
  drm/vgem: Fix return value check in vgem_init()
  drm/blend: Fix comment typ-o
  drm/stm: remove unneeded -Iinclude/drm compiler flag
  drm/vc4: fix include notation and remove -Iinclude/drm flag
  drm/pl111: Add a debugfs node to dump our registers.
  drm/pl111: make structure mode_config_funcs static
  drm/pl111: make structure pl111_display_funcs static
  drm/pl111: Register the clock divider and use it.
  drm: drop drm_[cm]alloc* helpers
  ...

Pull tty/serial fixes from Greg KH:
 "Here are some serial and tty fixes for 4.12-rc3. They are a bit bigger
  than normal, which is why I had them bake in linux-next for a few
  weeks and didn't send them to you for -rc2.

  They revert a few of the serdev patches from 4.12-rc1, and bring
  things back to how they were in 4.11, to try to make things a bit more
  stable there. Rob and Johan both agree that this is the way forward,
  so this isn't people squabbling over semantics. Other than that, just
  a few minor serial driver fixes that people have had problems with.

  All of these have been in linux-next for a few weeks with no reported
  issues"

* tag 'tty-4.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  serial: altera_uart: call iounmap() at driver remove
  serial: imx: ensure UCR3 and UFCR are setup correctly
  MAINTAINERS/serial: Change maintainer of jsm driver
  serial: enable serdev support
  tty/serdev: add serdev registration interface
  serdev: Restore serdev_device_write_buf for atomic context
  serial: core: fix crash in uart_suspend_port
  tty: fix port buffer locking
  tty: ehv_bytechan: clean up init error handling
  serial: ifx6x60: fix use-after-free on module unload
  serial: altera_jtaguart: adding iounmap()
  serial: exar: Fix stuck MSIs
  serial: efm32: Fix parity management in 'efm32_uart_console_get_options()'
  serdev: fix tty-port client deregistration
  Revert "tty_port: register tty ports with serdev bus"
  drivers/tty: 8250: only call fintek_8250_probe when doing port I/O

Pull powerpc fixes from Michael Ellerman:
 "Fix running SPU programs on Cell, and a few other minor fixes.

  Thanks to Alistair Popple, Jeremy Kerr, Michael Neuling, Nicholas
  Piggin"

* tag 'powerpc-4.12-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc: Add PPC_FEATURE userspace bits for SCV and DARN instructions
  powerpc/spufs: Fix hash faults for kernel regions
  powerpc: Fix booting P9 hash with CONFIG_PPC_RADIX_MMU=N
  powerpc/powernv/npu-dma.c: Fix opal_npu_destroy_context() call
  selftests/powerpc: Fix TM resched DSCR test with some compilers

Pull x86 fixes from Thomas Gleixner:
 "A series of fixes for X86:

   - The final fix for the end-of-stack issue in the unwinder
   - Handle non PAT systems gracefully
   - Prevent access to uninitiliazed memory
   - Move early delay calaibration after basic init
   - Fix Kconfig help text
   - Fix a cross compile issue
   - Unbreak older make versions"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/timers: Move simple_udelay_calibration past init_hypervisor_platform
  x86/alternatives: Prevent uninitialized stack byte read in apply_alternatives()
  x86/PAT: Fix Xorg regression on CPUs that don't support PAT
  x86/watchdog: Fix Kconfig help text file path reference to lockup watchdog documentation
  x86/build: Permit building with old make versions
  x86/unwind: Add end-of-stack check for ftrace handlers
  Revert "x86/entry: Fix the end of the stack for newly forked tasks"
  x86/boot: Use CROSS_COMPILE prefix for readelf

Pull timer fixlet from Thomas Gleixner:
 "Silence dmesg spam by making the posix cpu timer printks depend on
  print_fatal_signals"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  posix-timers: Make signal printks conditional

Pull RAS fixes from Thomas Gleixner:
 "Two fixlets for RAS:

   - Export memory_error() so the NFIT module can utilize it

   - Handle memory errors in NFIT correctly"

* 'ras-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  acpi, nfit: Fix the memory error check in nfit_handle_mce()
  x86/MCE: Export memory_error()

Pull perf tooling fixes from Thomas Gleixner:

 - Synchronization of tools and kernel headers

 - A series of fixes for perf report addressing various failures:
    * Handle invalid maps proper
    * Plug a memory leak
    * Handle frames and callchain order correctly

 - Fixes for handling inlines and children mode

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tools/include: Sync kernel ABI headers with tooling headers
  perf tools: Put caller above callee in --children mode
  perf report: Do not drop last inlined frame
  perf report: Always honor callchain order for inlined nodes
  perf script: Add --inline option for debugging
  perf report: Fix off-by-one for non-activation frames
  perf report: Fix memory leak in addr2line when called by addr2inlines
  perf report: Don't crash on invalid maps in `-g srcline` mode

Pull locking fix from Thomas Gleixner:
 "A fix for a state leak which was introduced in the recent rework of
  futex/rtmutex interaction"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  futex,rt_mutex: Fix rt_mutex_cleanup_proxy_lock()

Pull kthread fix from Thomas Gleixner:
 "A single fix which prevents a use after free when kthread fork fails"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  kthread: Fix use-after-free if kthread fork fails

Pull ftrace fixes from Steven Rostedt:
 "There's been a few memory issues found with ftrace.

  One was simply a memory leak where not all was being freed that should
  have been in releasing a file pointer on set_graph_function.

  Then Thomas found that the ftrace trampolines were marked for
  read/write as well as execute. To shrink the possible attack surface,
  he added calls to set them to ro. Which also uncovered some other
  issues with freeing module allocated memory that had its permissions
  changed.

  Kprobes had a similar issue which is fixed and a selftest was added to
  trigger that issue again"

* tag 'trace-v4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  x86/ftrace: Make sure that ftrace trampolines are not RWX
  x86/mm/ftrace: Do not bug in early boot on irqs_disabled in cpu_flush_range()
  selftests/ftrace: Add a testcase for many kprobe events
  kprobes/x86: Fix to set RWX bits correctly before releasing trampoline
  ftrace: Fix memory leak in ftrace_graph_release()