- 30 8月, 2010 1 次提交
-
-
由 Takashi Iwai 提交于
Instead of defining each content as a separate struct, put all into the definition of struct alc_fixup arrays so that reader doesn't go back to see the definition again. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 28 8月, 2010 1 次提交
-
-
由 Eliot Blennerhassett 提交于
If hw error is ignored, status is updated with invalid info. Signed-off-by: NEliot Blennerhassett <eblennerhassett@audioscience.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 26 8月, 2010 1 次提交
-
-
由 David Henningsson 提交于
The attached patch enables playback on a Sony VAIO machine. BugLink: http://launchpad.net/bugs/618271Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com> Cc: <stable@kernel.org> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 23 8月, 2010 1 次提交
-
-
由 Jerone Young 提交于
This patch adds quirk for the Lenovo S10-3t so the headphone & microphone jacks will now work. Signed-off-by: NJerone Young <jerone.young@canonical.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 20 8月, 2010 2 次提交
-
-
由 Takashi Iwai 提交于
The new sticky PCM parameter introduced the delayed clean-ups of stream- and channel-id tags. In the current implementation, this check (adding dirty flag) and actual clean-ups are done only for the codec chip. However, with HD-audio architecture, multiple codecs can be on a single bus, and the controller assign stream- and channel-ids in the bus-wide. In this patch, the stream-id and channel-id are checked over all codecs connected to the corresponding bus. Together with it, the mutex is moved to struct hda_bus, as this becomes also bus-wide. Reported-and-tested-by: NStephen Warren <swarren@nvidia.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
Intel and Nvidia HDMI codec drivers have own implementations of sticky PCM parameters. Now HD-audio core part already has it, thus both setups conflict. The fix is simply remove the part in patch_intelhdmi.c and patch_nvhdmi.c and simply call snd_hda_codec_setup_stream() as usual. Reported-and-tested-by: NStephen Warren <swarren@nvidia.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 19 8月, 2010 3 次提交
-
-
由 Daniel T Chen 提交于
BugLink: https://bugs.launchpad.net/bugs/619439 This ThinkPad model needs External Amplifier muted for audible playback, so set the inv_eapd quirk for it. Reported-and-tested-by: NDennis Bell <dennis.bell@parkerg.co.uk> Cc: <stable@kernel.org> Signed-off-by: NDaniel T Chen <crimsun@ubuntu.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
hdmi_eld_update_pcm_info() must be always compiled in. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Charles Chin 提交于
Just added new codec ids. These are almost compatible with existing ones. Signed-off-by: NCharles Chin <Charles.Chin@idt.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 18 8月, 2010 1 次提交
-
-
由 Jaroslav Kysela 提交于
With some hardware combinations, the PCM interrupts are acknowledged before the period boundary from the emu10k1 chip. The midlevel PCM code gets confused and the playback stream is interrupted. It seems that the interrupt processing shift by 2 samples is enough to fix this issue. This default value does not harm other, non-affected hardware. More information: Kernel bugzilla bug#16300 [A copmile warning fixed by tiwai] Signed-off-by: NJaroslav Kysela <perex@perex.cz> Cc: <stable@kernel.org> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 17 8月, 2010 1 次提交
-
-
由 Kailang Yang 提交于
- Fix capture mixer elements for ALC680 base model - Support auto change ADC for recording from MIC - Cancel capture source assigned in auto mode. Signed-off-by: NKailang Yang <kailang@realtek.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 16 8月, 2010 2 次提交
-
-
由 Takashi Iwai 提交于
model=dell-vostro is needed for Dell Vostro 1220 with Coexnat 5067. Reference: Novell bnc#631066 https://bugzilla.novell.com/show_bug.cgi?id=631066 Cc: <stable@kernel.org> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
The detection and loading of firmeware on riptide driver has been broken due to rewrite of some codes, checking the presense wrongly. This patch fixes the logic again. Reference: kernel bug 16596 https://bugzilla.kernel.org/show_bug.cgi?id=16596 Cc: <stable@kernel.org> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 13 8月, 2010 2 次提交
-
-
由 Takashi Iwai 提交于
The commit eb541337 ALSA: hda - Make converter setups sticky changes the semantics of snd_hda_codec_cleanup_stream() not to clean up the stream at that moment but delay the action. This broke the codes expecting that the clean-up is done immediately, such as dynamic ADC changes in some codec drivers. This patch fixes the issue by introducing a lower helper, __snd_hda_codec_cleanup_stream(), to allow the immediate clean up. The original snd_hda_codec_cleanup_stream() is kept as is now. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
When a device is plugged over HDMI, it passes some information in ELD including the supported PCM parameters like formats, rates, channels. This patch adds the check to PCM open callback of HDMI streams so that only valid parameters the device supports are used. When no device is plugged, the parameters the codec supports are used; it's mostly all parameters the hardware can work. This is for apps that are started before device plugging and do probing (e.g. a sound daemon), so that at least, probing would work even before the device plugging. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 10 8月, 2010 3 次提交
-
-
由 Charles Chin 提交于
Added the entries for 92HD87B1/3 and 92HD87B2/4 codecs. These are compatible with existing 83xxx codecs. Signed-off-by: NCharles Chin <Charles.Chin@idt.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 David Henningsson 提交于
Two users report model=auto is needed to make the internal mic work properly. BugLink: https://bugs.launchpad.net/bugs/495134Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Stephen Warren 提交于
* Add missing codec IDs. * Modify some existing codec names for discrete GPUs to match newly added IDs. Note: existing names were a mixture of marketing and engineering GPU names. Equally, there's no reason that codec IDs have to be specific to a particular GPU or board, so identify codecs in a less marketing-oriented fashion. * Reformat codec ID table so it's easier to read, for me at least. Signed-off-by: NStephen Warren <swarren@nvidia.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 09 8月, 2010 3 次提交
-
-
由 Takashi Iwai 提交于
The Conexant CX20584 with 141f:5068 seems compatible with other cxt5066 code. Just add the missing id. Tested-by: NCristopher Camacho Leandro <ccamacho@linuxmail.org> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Steven Eastland 提交于
This provides a new model and pin config for the snd-hda-intel 92HD83XXX codec for hp laptop model dv7-4000, enabling the subwoofer. Signed-off-by: Steven Eastland <seastland at gmail.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Jonathan Woithe 提交于
I discovered tonight that ALSA no longer sets up a stream for the second ADC provided by the Realtek ALC260 HDA codec. At some point alc_build_pcms() started using stream_analog_alt_capture when constructing the second ADC stream, but patch_alc260() was never updated accordingly. I have no idea when this regression occurred. The trivial patch to patch_alc260() given below fixes the problem as far as I can tell. The patch is against 2.6.35. Signed-off-by: NJonathan Woithe <jwoithe@physics.adelaide.edu.au> Cc: <stable@kernel.org> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 06 8月, 2010 2 次提交
-
-
由 Takashi Iwai 提交于
So far, we reset the converter setups like the stream-tag, the channel-id and format-id in prepare callbacks, and clear them in cleanup callbacks. This often causes a silence of the digital receiver for a couple of seconds. This patch tries to delay the converter setup changes as much as possible. The converter setups are cached and aren't reset as long as the same values are used. At suspend/resume, they are cleared to be recovered properly, too. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Kailang Yang 提交于
Signed-off-by: NKailang Yang <kailang@realtek.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 05 8月, 2010 2 次提交
-
-
由 Takashi Iwai 提交于
The NID 0x11 on HP dc5750 with ALC260 should be a speaker although BIOS gives it as a line-out. This patch adds a quirk to fix the pin config so that the real line-out is used properly. Reference: bnc#624118 https://bugzilla.novell.com/show_bug.cgi?id=624118Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Ondrej Zary 提交于
My previous patch assumed that the DMA mode (represented by 3 lowest bits of ALS4K_GCR99_DMA_EMULATION_CTRL register) is set to the default value 0. If that's not the case, it might result in invalid mode to be set. This patch fixes this potential problem. Signed-off-by: NOndrej Zary <linux@rainbow-software.org> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 04 8月, 2010 2 次提交
-
-
由 Ondrej Zary 提交于
Enable burst mode to prevent dropouts during high PCI bus usage. The card is useless in X without this because of dropouts when anything moves on the screen (at least with PCI VGA card). Enabling this is also recommended by the datasheet (page 48). Signed-off-by: NOndrej Zary <linux@rainbow-software.org> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
In patch_alc269(), we initialize the primary capsrc so that the device works from the beginning. It issues CONNECT_SEL verb no matter which widget is although some widget (e.g. 0x23) has no connection selection but a mixer, which requires unmuting instead. This patch fixes the initialization of capsrc by re-using the code as a helper function. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 03 8月, 2010 8 次提交
-
-
由 Takashi Iwai 提交于
An Intel board needs a white-list entry to enable PC-beep. Otherwise the driver misdetects (due to bogus BIOS info) and ignores the PC-beep on 2.6.35. Reported-and-tested-by: NLeandro Lucarella <luca@llucax.com.ar> Cc: <stable@kernel.org> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
Since the pending periods are often bogus and take long time until actually processed, it often results in a high CPU usage of the hd-audio workq. Overall it's better to have low CPU consumption by avoiding a too tight loop rather than the wake-up timing accuracy. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
Define constants for the HD-audio stream format bits, and replace the magic numbers in codes. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Daniel J Blueman 提交于
Fix HDA beep frequency on IDT 92HD73xx and 92HD71Bxx codecs. These codecs use the standard beep frequency calculation although the datasheet says it's linear frequency. Other IDT/STAC codecs might have the same problem. They should be fixed individually later. Signed-off-by: NDaniel J Blueman <daniel.blueman@gmail.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Anssi Hannula 提交于
Passing IEC 61937 encapsulated compressed audio at bitrates over 6.144 Mbps (i.e. more than a single 2-channel 16-bit 192kHz IEC 60958 link) over HDMI requires the use of HBR Audio Stream Packets instead of Audio Sample Packets. Enable HBR mode when the stream has 8 channels and the Non-PCM bit is set. If the audio converter is not connected to any HBR-capable pins, return -EINVAL in prepare(). Signed-off-by: NAnssi Hannula <anssi.hannula@iki.fi> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Anssi Hannula 提交于
Set bit 15 (Stream Type) of HDA Stream Format to 1 (Non-PCM) when IEC958 channel status bit 1 (AES0 & 0x02) is set to 1 (non-audio). This is a prequisite for HDMI HBR passthrough. Signed-off-by: NAnssi Hannula <anssi.hannula@iki.fi> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Jerone Young 提交于
Just as with the X301. The X300 does not have a way to do SPDIF either. It does not have a dock connector, nor does it have the SPDIF through the headphone jack. This patch fixes it so X300 does not show SPDIF, since it cannot do it. To add all Lenovo Thinkpads had different codec subsytem IDs: X300: http://launchpadlibrarian.net/34862838/Card0.Codecs.codec.0.txtSigned-off-by: NJerone Young <jerone.young@canonical.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Jerone Young 提交于
ALSA: hda - FIX to not expose SPDIF on Thinkpad X301, since it does not have the ability to use SPDIF The Lenovo X301 does not have the ability to connect to a docking station to use the SPDIF port. It also does not have the ability to do SPDIF though the headphone jack or Display Port jacks. This patch fixes it so this is not exposed for the X301 and users do think it has the ability to do SPDIF. I tested both headphone & display port jacks and it is not there. I have tested this patch and it works great. Also to add the other Thinkpads have different subsystem codec IDs. Here are examples: X301: http://launchpadlibrarian.net/31561902/Card0.Codecs.codec.0.txt X200: http://launchpadlibrarian.net/49055036/Card0.Codecs.codec.0.txt W500: http://launchpadlibrarian.net/36276057/Card0.Codecs.codec.0.txtSigned-off-by: NJerone Young <jerone.young@canonical.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 02 8月, 2010 1 次提交
-
-
由 David Henningsson 提交于
Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 30 7月, 2010 4 次提交
-
-
由 Takashi Iwai 提交于
The current ALC259/268/269 parser ignores some pins as unhandled, but user won't notice what goes wrong. So, added a warning message for the ignored pins as a hint. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
The pin NID 0x1a should be handled as well as NID 0x1b. Also added comments. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
Call snd_hda_shutup_pins() for power-saving and reboot-notifier in patch_conexant.c as well as other codecs. This will reduce the pop noise in power-save mode. Reference: bnc#624896 https://bugzilla.novell.com/show_bug.cgi?id=624896Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
If BIOS sets up the input pin as VREF 50, use the value as is instead of overriding forcibly to VREF 80. This fixes the quality of inputs on some devices like Packard-Bell M5210. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-