Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 25 7月, 2009 6 次提交
    • P
      OMAP2/3 clock: split, rename omap2_wait_clock_ready() · 72350b29
      由 Paul Walmsley 提交于 
      Some OMAP2/3 hardware modules have CM_IDLEST attributes that are not
handled by the current omap2_wait_clock_ready() code.  In preparation
for patches that fix the unusual devices, rename the function
omap2_wait_clock_ready() to omap2_wait_module_ready() and split it
into three parts:

1. A clkops-specific companion clock return function (by default,
   omap2_clk_dflt_find_companion())

2. A clkops-specific CM_IDLEST register address and bit shift return
   function (by default, omap2_clk_dflt_find_idlest())

3. Code to wait for the CM to indicate that the module is ready
   (omap2_cm_wait_idlest())

Clocks can now specify their own custom find_companion() and find_idlest()
functions; used in subsequent patches.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
      72350b29
    • R
      OMAP3 SDRC: Move the clk stabilization delay to the right place · df56556e
      由 Rajendra Nayak 提交于 
      The clock stabilization delay post a M2 divider change is needed
even before a SDRC interface clock re-enable and not only before
jumping back to SDRAM.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
      df56556e
    • R
      OMAP3 SDRC: Fix freeze when scaling CORE dpll to < 83Mhz · 8ff120e5
      由 Rajendra Nayak 提交于 
      This patch fixes a bug in the CORE dpll scaling sequence which was
errouneously clearing some bits in the SDRC DLLA CTRL register and
hence causing a freeze.  The issue was observed only on platforms
which scale CORE dpll to < 83Mhz and hence program the DLL in fixed
delay mode.

Issue reported by Limei Wang <E12499@motorola.com>, with debugging
assistance from Richard Woodruff <r-woodruff2@ti.com> and Girish
Ghongdemath <girishsg@ti.com>.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Cc: Limei Wang <E12499@motorola.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Girish Ghongdemath <girishsg@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
[paul@pwsan.com: updated patch description to include collaboration credits]
      8ff120e5
    • P
      OMAP2/3 SDRC: don't set SDRC_POWER.PWDENA on boot · 75f251e3
      由 Paul Walmsley 提交于 
      Stop setting SDRC_POWER.PWDENA on boot.  There is a nasty erratum
(34xx erratum 1.150) that can cause memory corruption if PWDENA is
enabled.

Based originally on a patch from Samu P. Onkalo <samu.p.onkalo@nokia.com>.

Tested on BeagleBoard rev C2.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Samu P. Onkalo <samu.p.onkalo@nokia.com>
      75f251e3
    • J
      OMAP3: Setup MUX settings for SDRC CKE signals · 9fb97412
      由 Jean Pihet 提交于 
      This patches ensures the MUX settings are correct for the SDRC
CKE signals to SDRAM. This allows the self-refresh to work when
2 chip-selects are in use.

A warning is thrown away in case the initial muxing is incorrect,
in order to track faulty or old-dated bootloaders.
Note: The CONFIG_OMAP_MUX and CONFIG_OMAP_MUX_WARNINGS options
must be enabled for the mux code to have effect.
Signed-off-by: NJean Pihet <jpihet@mvista.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
      9fb97412
    • J
      OMAP3 SDRC: add support for 2 SDRAM chip selects · 58cda884
      由 Jean Pihet 提交于 
      Some OMAP3 boards (Beagle Cx, Overo, RX51, Pandora) have 2
SDRAM parts connected to the SDRC.

This patch adds the following:
- add a new argument of type omap_sdrc_params struct*
to omap2_init_common_hw and omap2_sdrc_init for the 2nd CS params
- adapted the OMAP boards files to the new prototype of
omap2_init_common_hw
- add the SDRC 2nd CS registers offsets defines
- adapt the sram sleep code to configure the SDRC for the 2nd CS

Note: If the 2nd param to omap2_init_common_hw is NULL, then the
parameters are not programmed into the SDRC CS1 registers

Tested on 3430 SDP and Beagleboard rev C2 and B5, with
suspend/resume and frequency changes (cpufreq).
Signed-off-by: NJean Pihet <jpihet@mvista.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
      58cda884
  3. 23 6月, 2009 5 次提交
  5. 20 6月, 2009 9 次提交
  7. 09 6月, 2009 3 次提交
  9. 29 5月, 2009 17 次提交