Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

CPUIMX51 is build around Freescale's i.MX515 and has up to
512MB of RAM, NAND Flash, Ethernet, USB Host with 4 ports
hub, USB OTG, ST16554 Quad UART on nCS1, I2C RTC ...

MBIMX51 adds LEDS, Keypad, TSC2007 touchscreen controler ...
Signed-off-by: NEric Bénard <eric@eukrea.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The pads capable of being used as GPIOs had their pad-name and mode-name
switched. Also, fix the following:

- Whitespace fixes
- Replace IOMUX_CONFIG_ALTn with 'n'
Signed-off-by: NAmit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Add device registration and setup IOMUX pins in the mx51_babbage
board feil.
Signed-off-by: NDinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch de-asserts the reset line that is connected to the USB
ULPI PHY on USB Host1.

This patch should be included with the original USB host enablement
set of patches of mx51 babbage hw, but was accidentily left out.
Signed-off-by: NDinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch enables usb gadget for freescale mx51 babbage hw. By default,
the OTG port will be in device mode. To put the OTG port into Host mode,
pass "otg_mode=host" in the exec command.

This patch applies to 2.6.34-rc7.
Signed-off-by: NDinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch enables USB host functionality for Host1 and OTG port on
Freescale MX51 Babbage HW. This patch contains the board specific
HW initialization of the USB HW.

This patch applies to 2.6.34-rc6.
Signed-off-by: NDinh Nguyen <Dinh.Nguyen@freescale.com>
Reviewed-by: NDaniel Mack <daniel@caiaq.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch is to be applied into Sascha's mxc-master branch.

Fix ckih2 parameter in mx51_clocks_init funtion. CKIH2 pin is left unconnected on Babbage.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NAmit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Babbage is a reference board from Freescale for their i.MX51 SoC.

Add board definition, Kconfig and Makefiles to enable Freescale i.MX51
processor and Babbage board.

Boot tested on a Babbage2.5 board
Signed-off-by: NAmit Kucheria <amit.kucheria@canonical.com>