The !defined(MODULE) conditional has been added to the
OF_EARLYCON_DECLARE() define.

Now we can revert commit a2d3ea2f ("serial: 8250/uniphier:
fix modular build").
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Keep earlycon related symbols only when CONFIG_SERIAL_EARLYCON is
enabled and the driver is built-in.  This will be helpful to clean
up ifdefs surrounding earlycon code in serial drivers.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch permits the usage for GPIOs to control
the CTS/RTS/DTR/DSR/DCD/RI signals.
Signed-off-by: NYegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This workaround is needed for the cases, where mctrl_gpio API is used
before mctrl_gpio_init() was invoked. This happens in 8250 during
console initialization, as the driver sets DTR signal.
Signed-off-by: NYegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

mctrl_gpio_get_outputs() returns the state of following signals:

RTS, DTR

While defining the routine for reading outputs, fix the comment for
mctrl_gpio_get() routine as it returns only the state of the input
signals.
Signed-off-by: NYegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Introduce serial8250_out_MCR() and serial8250_in_MCR() routines, that
replace following calls:

serial_out(port, UART_MCR, val)
serial_port_out(up, UART_MCR, val)
serial_in(port, UART_MCR)

This patch is needed in order to integrate reading/writing of MCR
signals via SERIAL_MCTRL_GPIO infrastructure later.
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NYegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In DNV, when RX DMA is used and number of bytes received is less than
transfer size, only RX DMA timeout interrupt is sent. When this happens,
read the RX buffer.
Signed-off-by: NChuah, Kim Tatt <kim.tatt.chuah@intel.com>
Acked-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Export serial8250_rx_dma_flush() for use by SOC UART drivers.
Signed-off-by: NChuah, Kim Tatt <kim.tatt.chuah@intel.com>
Acked-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

To allow other code to safely read DMA Channel Status Register (where
the register attribute for Channel Error, Descriptor Time Out &
Descriptor Done fields are read-clear), export hsu_dma_get_status().
hsu_dma_irq() is renamed to hsu_dma_do_irq() and requires Status
Register value to be passed in.
Signed-off-by: NChuah, Kim Tatt <kim.tatt.chuah@intel.com>
Acked-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When using the 8250 as a boot console and the main console results in
messages being printed twice.  The console framework will only
unregister boot consoles if a new console is registered with the
CON_CONSDEV flag set.

Set this flag for the univ8250 console to prevent double-registration.
Signed-off-by: NMatthew Leach <matthew.leach@codethink.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver makes use of the __set_bit() and __clear_bit() functions.
When running under big-endian, these functions don't convert the bit
indexes when working with peripheral registers, leading to the
incorrect bits being set and cleared when running big-endian.

Add two new driver functions for setting and clearing bits that are
byte-order aware.
Signed-off-by: NMatthew Leach <matthew@mattleach.net>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix the serial access code to deal with kernels built for big endian
operation.
Signed-off-by: NMatthew Leach <matthew@mattleach.net>
Acked-by: NBen Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The fifo mask functions should be static as they are not
used outside of the driver. Fix the following warnings by
making them static:

drivers/tty/serial/sirfsoc_uart.h:109:5: warning: symbol 'uart_usp_ff_full_mask' was not declared. Should it be static?
drivers/tty/serial/sirfsoc_uart.h:117:5: warning: symbol 'uart_usp_ff_empty_mask' was not declared. Should it be static?
Signed-off-by: NBen Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The Kconfig currently controlling compilation of mps2-uart is:

config SERIAL_MPS2_UART
	bool "MPS2 UART port"
	depends on ARM || COMPILE_TEST

...meaning that it currently is not being built as a module by anyone.

Follow commit 89ebc274 ("drivers/tty: make serial/mvebu-uart.c
explicitly non-modular") as an example of moving modular code to
non-modular:

- remove the modular code that is essentially orphaned, so that
  when reading the driver there is no doubt it is builtin-only.

- explicitly disallow a driver unbind, since that doesn't have a
  sensible use case anyway, and it allows us to drop the ".remove"
  code for non-modular drivers.

- use arch_initcall instead of module_init and remove module_exit.

Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Reported-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NVladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

As suggested by the serial port infrastructure documentation, the IRQ is
requested in ->startup(). However, it is never freed in the ->shutdown()
hook.

With simple systems that open the serial port once for all and always
have at least one process that keep the serial port opened, there was no
problem. But with a more complicated system (*cough* systemd *cough*),
the serial port is opened/closed many times, which at some point no
processes having the serial port open at all. Due to this ->startup()
gets called again, tries to request_irq() again, which fails.

Fixes: 30530791 ("serial: mvebu-uart: initial support for Armada-3700 serial port")
Cc: <stable@vger.kernel.org>
Cc: Ofer Heifetz <oferh@marvell.com>
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The bcm63xx_uart driver uses the of alias for determing its id. Recent
changes in dts files changed the expected 'uartX' to the recommended
'serialX', breaking serial output. Fix this by checking for a 'serialX'
alias as well.

Fixes: e3b992d0 ("MIPS: BMIPS: Improve BCM6328 device tree")
Fixes: 2d52ee82 ("MIPS: BMIPS: Improve BCM6368 device tree")
Fixes: 7537d273 ("MIPS: BMIPS: Add device tree example for BCM6358")
Signed-off-by: NJonas Gorski <jogo@openwrt.org>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The Kconfig currently controlling compilation of this code is:

drivers/tty/serial/Kconfig:config SERIAL_M32R_SIO
drivers/tty/serial/Kconfig:     bool "M32R SIO I/F"

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.

We don't replace module.h with init.h since the file already has that.

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The Kconfig currently controlling compilation of this code is:

drivers/tty/serial/Kconfig:config SERIAL_VT8500
drivers/tty/serial/Kconfig:     bool "VIA VT8500 on-chip serial port support"

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.

Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.

We don't replace module.h with init.h since the file already has that.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.

Cc: Tony Prisk <linux@prisktech.co.nz>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Alexey Charkov <alchark@gmail.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The Kconfig currently controlling compilation of this code is:

drivers/tty/serial/Kconfig:config SERIAL_PXA
drivers/tty/serial/Kconfig:     bool "PXA serial port support"

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.

Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.

Also note that MODULE_DEVICE_TABLE and MODULE_ALIAS are both a
no-op for non-modular builds.

We also delete the MODULE_LICENSE tag since that information is
already contained at the top of the file in the comments.

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add COMPILE_TEST for the compilation test coverage.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch makes assignment of port line automatically,
so now user allow to use several MAX310X chips.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add uart_remove_one_port() for error path.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch moves UART registration at module_init initcall,
so this should helps to add multiple chip support in the future.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use resource managed functions devm_gpiochip_add_data() to make
error & exit path a bit simpler.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

RS485 IOCTLs uses spinlocks, so move regmap functions into a separate
work queue.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Adds support for the WCH CH355 4S card in the 8250 serial driver.
Signed-off-by: NAlexandr Petrenko <petrenkoas83@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

On non-DeviceTree platforms, the index of serial device is a static
variable incremented on each probe.  It is incremented even if deferred
probe happens when getting the clock in s3c24xx_serial_init_port().

This index is used for referencing elements of statically allocated
s3c24xx_serial_ports array.  In case of re-probe, the index will point
outside of this array leading to memory corruption.

Increment the index only on successful probe.
Reported-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Fixes: b497549a ("[ARM] S3C24XX: Split serial driver into core and per-cpu drivers")
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When the clk_get() of "uart" clock returns EPROBE_DEFER, the next re-probe
finishes with success but uses invalid (ERR_PTR) values.  This leads to
dereferencing of ERR_PTR stored under ourport->clk:

	12c30000.serial: Controller clock not found
	(...)
	12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 61, base_baud = 0) is a S3C6400/10
	Unable to handle kernel paging request at virtual address fffffdfb

	(clk_prepare) from [<c039f7d0>] (s3c24xx_serial_pm+0x20/0x128)
	(s3c24xx_serial_pm) from [<c0395414>] (uart_change_pm+0x38/0x40)
	(uart_change_pm) from [<c039689c>] (uart_add_one_port+0x31c/0x44c)
	(uart_add_one_port) from [<c03a035c>] (s3c24xx_serial_probe+0x2a8/0x418)
	(s3c24xx_serial_probe) from [<c03ee110>] (platform_drv_probe+0x50/0xb0)
	(platform_drv_probe) from [<c03ecb44>] (driver_probe_device+0x1f4/0x2b0)
	(driver_probe_device) from [<c03eb0c0>] (bus_for_each_drv+0x44/0x8c)
	(bus_for_each_drv) from [<c03ec8c8>] (__device_attach+0x9c/0x100)
	(__device_attach) from [<c03ebf54>] (bus_probe_device+0x84/0x8c)
	(bus_probe_device) from [<c03ec388>] (deferred_probe_work_func+0x60/0x8c)
	(deferred_probe_work_func) from [<c012fee4>] (process_one_work+0x120/0x328)
	(process_one_work) from [<c0130150>] (worker_thread+0x2c/0x4ac)
	(worker_thread) from [<c0135320>] (kthread+0xd8/0xf4)
	(kthread) from [<c0107978>] (ret_from_fork+0x14/0x3c)

The first unsuccessful clk_get() causes s3c24xx_serial_init_port() to
exit with failure but the s3c24xx_uart_port is left half-configured
(e.g. port->mapbase is set, clk contains ERR_PTR).  On next re-probe,
the function s3c24xx_serial_init_port() will exit early with success
because of configured port->mapbase and driver will use old values,
including the ERR_PTR as clock.

Fix this by cleaning the port->mapbase on error path so each re-probe
will initialize all of the port settings.

Fixes: 60e93575 ("serial: samsung: enable clock before clearing pending interrupts during init")
Cc: <stable@vger.kernel.org>
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Tested-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Tested-by: NKevin Hilman <khilman@baylibre.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Some BIOS only use _OSI("Linux") to distinguish between Linux & Windows.
Apply Level/Low to UART trigger mode if Windows, Edge/High mode otherwise.
But since 2.6.23 the mainline kernel no longer returns true for
_OSI(“Linux”).

The default IRQ0~15 trigger mode in Linux is Edge/High mode without
ACPI MADT override. It mismatches IRQ mode and makes UART malfunctional on
such motherboard.

This patch will check the current IRQ mode and apply correct mode to UART.

The following link is F81216AD spec PDF:
http://html.alldatasheet.com/html-pdf/257956/FINTEK/F81216AD/5569/
25/F81216AD.html

LDN0~3
	70h: IRQ channel & Mode register
		Bit 6~5	:
			00	: Active low level mode
			01	: Active high edge mode
		Bit 4	: Sharing Flag (0: not share/1: share)
		Bit 3~0 : IRQ channel
Signed-off-by: NJi-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Submitters of device tree binding documentation may forget to CC
the subsystem maintainer if this is missing.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-serial@vger.kernel.org
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Allocated memory for 'sport->irq_fault_name' is freed twice, first
in error check of 'if(!sport->irq_rx_name)' and other in fallback
handler.
Signed-off-by: NPurna Chandra Mandal <purna.mandal@microchip.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently the clocks are enabled at probe and disabled
at remove. Instead enable the clocks when used.
Signed-off-by: NShubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When using DMA, half duplex doesn't work properly because rx is not stopped
before starting tx. Ensure we call atmel_stop_rx() in the DMA case.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

There is a macro named ATMEL_SERIAL_RINGSIZE which suggesting that it
corresponds to the real size of the ring buffer. Let warn people that
there is a factor of four since allocation size is
sizeof(struct atmel_uart_char) * ATMEL_SERIAL_RINGSIZE.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Split TX and RX paths to not schedule RX tasklet on TX events and vice versa.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The IRQ status check and related actions was done in the tasklet without
benefit. So, move it back to the IRQ context to simplify IRQ handling and
having the possibility to split the tasklet in two separated ones for
receive and transmit actions.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use memdup_user to duplicate a memory region from user-space to
kernel-space, instead of open coding using kmalloc & copy_from_user.
Signed-off-by: NMuhammad Falak R Wani <falakreyaz@gmail.com>
Reviewed-by: NSamuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Doing the following UART bind/unbind sequence on a i.mx platform causes
a kernel crash due to NULL pointer dereference:

echo  21f4000.serial > /sys/bus/platform/drivers/imx-uart/bind
echo  21f4000.serial > /sys/bus/platform/drivers/imx-uart/unbind

Fix this problem by adding NULL checks prior to calling release/request_port
ops.
Reported-by: NFugang Duan <fugang.duan@nxp.com>
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Tested-by: NFugang Duan <fugang.duan@nxp.com>
Acked-by: NFugang Duan <fugang.duan@nxp.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Enabling support for the UART on the ARM MPS2 platform only make sense
when compiling for the ARM MPS2 platform, unless compile-testing.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: NVladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>