Support for the SBC610 VPX Single Board Computer from GE Fanuc (PowerPC
MPC8641D).

This patch adds support for the registers held in the devices main FPGA,
exposing extra information about the revision of the board through cpuinfo.
Signed-off-by: NMartyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The Freescale Elo DMA driver binds to all DMA channels in the device tree that
are compatible with "fsl,eloplus-dma-channel".  This conflicts with the sound
drivers for the MPC8610 HPCD.  On this board, the SSI uses two DMA channels and
therefore those channels are not available for general purpose use.  We
change the compatible properties for these channels "fsl,ssi-dma-channel".
This works because the sound drivers don't actually check the compatible
property when it grabs channels.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The RTC is sitting on the I2C1 bus at address 0x68. RTC interrupt signal
is connected to the IPIC's EXT3 interrupt line.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Uses mpc83xx_add_bridge in fsl_pci.c

Adds second register tuple to pci node register property
as done for 83xx device trees in a previous patch.
Signed-off-by: NJohn Rigby <jrigby@freescale.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Modify mpc83xx_add_bridge to get config space register base address from
the device tree instead of immr + hardcoded offset.

83xx pci nodes have this change:
    register properties now contain two address length tuples:
	First is the pci bridge register base, this has always been there.
	Second is the config base, this is new.

This is documented in dts-bindings/fsl/83xx-512x-pci.txt

The changes accomplish these things:
    mpc83xx_add_bridge no longer needs to call get_immrbase
    it uses hard coded addresses if the second register value is missing
Signed-off-by: NJohn Rigby <jrigby@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Support for the SBC610 VPX Single Board Computer from GE Fanuc (PowerPC MPC8641D).

A number of MPC8641D based route interrupts for on-board interrupts through
a FPGA based interrupt controller, which is chained with the
MPC8641D's mpic. This patch provides a basic driver to allow basic routing
of interrupts to the mpic.
Signed-off-by: NMartyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add interrupt info to the MPC8536DS .dts for the RTC
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Basic functionality for the AMCC Arches eval Board.
Signed-off-by: NVictor Gallardo <vgallardo@amcc.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add the fsl,playback-dma and fsl,capture-dma properties to the Freescale
MPC8610 HPCD device tree.  These properties connect the SSI nodes to the
DMA nodes for the DMA channels that the SSI should use.  Also update the
ssi.txt documentation.

These properties will be needed when the ASoC V2 version of the Freescale
MPC8610 device drivers are merged into the mainline.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Support for the SBC610 VPX Single Board Computer from GE Fanuc (PowerPC
MPC8641D).

This is the basic board support for GE Fanuc's SBC610, a 6U single board
computer, based on Freescale's MPC8641D.
Signed-off-by: NMartyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This patch adds the localbus node, moves the bcsr node into the
localbus node, and adds the flash node.

Also enable MTD support in the defconfig.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NHeiko Schocher <hs@denx.de>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Supported SMC1 (serial console), SCC3 Ethernet (10Mbps hdx).
Signed-off-by: NHeiko Schocher <hs@denx.de>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This patch adds support for the AD7414 temperature sensor
on Sequoia PPC440EPx board.
Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com>
Acked-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Add the Yosemite board to the explicitly supported list for ppc44x_simple
boards and remove the compatible entry for bamboo from the DTS file.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Add explicit support for the AMCC Glacier eval board to Kconfig and the
ppc44x_simple file.  Also removes the cayonlands compatible entry from the
DTS file.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Due to the missing compatible property for the SOC, the MPC I2C buses are
not found any more. This patch fixes this issue. Furthermore it corrects
the name of the SOC node and adds the missing I2C node for the RTC.
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

When we coverted the .dts to v1 we lost a space between the irq
and its polarity/sense information.  This causes a bit of chaos
as the reset of the blob is off by one cell.

This was noticed by booting and getting errors w/ATA due to
lock of interrupts.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

FPGA offset in NOR flash was converted incorrectly when switching from
64M to 4M flash.
Signed-off-by: NSean MacLennan <smaclennan@pikatech.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Added support for the new at24 eeprom driver.
Documented a new fpga section, the DMA scatter gather list.
Removed index from i2c. No longer needed.
Fixed the leds section.
Signed-off-by: NSean MacLennan <smaclennan@pikatech.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

add simple-bus compatible property to soc nodes for 83xx/85xx platforms
that were missing them.  Add same to platform probe code.

This fixes SoC device drivers (such as talitos) to succeed in matching
devices present in the soc node.

also update mpc836x_rdk dts to new SEC bindings (overlooked in commit
3fd44736: powerpc/fsl: update crypto node definition and device tree
instances).
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The ULI "Super South Bridge" contains ISA bridge to the legacy
devices, such as Super IO mouse/keyboard/floppy disk controllers,
parallel port, i8259 interrupt controller and so on.

i8259 is disabled on the MPC8610HPCD, and other peripherals are not
traced out. So we use only RTC.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The mpc7448hpc2 board doesn't have an alias block like
most of the other modern eval boards have.  We need this
block in order to have u-boot be able to make use of the
CONFIG_OF_STDOUT_VIA_ALIAS (vs. having a hard coded node)
in the future.

Also remove the old, redundant chosen node.  Of all the modern
Freescale eval boards (incl. 83xx, 85xx, 86xx) this is the only
one which still has it.  Its presence also breaks with some older
versions of u-boot, like 1.3.1 -- which try and insert a
second chosen node.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

delete obsolete device-type property, delete model property
(use compatible property instead), prepend "fsl," to Freescale
specific properties. Add nodes to device trees that are missing them,
and fix broken property values in other trees.
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Initialize I2C pins on boards with CPM1/CPM2 controllers and document the
i2c bus in booting-without-of.

The boards don't have any I2C chips connected to the I2C bus, so unless
some external chips are connected to the boards, this code is just an
example of setting everything else up.
Signed-off-by: NJochen Friedrich <jochen@scram.de>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add support for the MPC8536 process and MPC8536DS reference board.  The
MPC8536 is an e500v2 based SoC which eTSEC, USB, SATA, PCI, and PCIe.

The USB and SATA IP blocks are similiar to those on the PQ2 Pro SoCs and
thus use the same drivers.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

It adds the missing RTC node to tqm8548.dts and enables support for
I2C, DS1307 and LM75 in the default configuration.
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

i8259 PIC is disabled on MPC8610HPCD, and ULi IDE is configured to use
PCI sideband interrupt that is specified in the device tree.

Current HPCD's device tree specify that IDE interrupt is low to high
sensitive, but in practice ULi IDE throws active-high interrupts (not
active-low as all normal PCI devices).
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Rename MPIC label to mpic to match all other 85xx .dts and to fix compile
issue introduced by addition of the DMA node.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Current device tree is only bare bones.  This patch adds nodes to make
it a complete tree for the MPC5121ads.

Added nodes include:
    mbx      - opengl coprocessor
    nfc      - nand flash controller
    cpld-pic - on board cpld
    rtc
    clock    - clock control
    pmc      - power management control
    gpio
    mscan    - can module
    i2c
    axe      - audio coprocessor
    display  - display interface unit
    mdio
    ethernet
    usb
    ioctl    - pin config
    pata
    ac97     - PSC configured as AC97
    pscfifo  - psc fifo configuration
    dma
    pci

Fix typo in header changing MDS to ADS.

Add a compatible property of the form "fsl,mpc5121-..."
to nodes missing one.

Changed localbus compatible to fsl,mpc5121-localbus, this does
not break anything because the only code that uses it finds it
via the node name, not compatible.
Signed-off-by: NJohn Rigby <jrigby@freescale.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This patch adds the still missing FDT nodes for the MSCAN devices for
the TQM52xx modules.
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Various instances of the EMAC core have varying: 1) number of address
match slots, 2) width of the registers for handling address match slots,
3) number of registers for handling address match slots and 4) base
offset for those registers.

As the driver stands today, it assumes that all EMACs have 4 IAHT and
GAHT 32-bit registers, starting at offset 0x30 from the register base,
with only 16-bits of each used for a total of 64 match slots.

The 405EX(r) and 460EX now use the EMAC4SYNC core rather than the EMAC4
core. This core has 8 IAHT and GAHT registers, starting at offset 0x80
from the register base, with ALL 32-bits of each used for a total of
256 match slots.

This adds a new compatible device tree entry "emac4sync" and a new,
related feature flag "EMAC_FTR_EMAC4SYNC" along with a series of macros
and inlines which supply the appropriate parameterized value based on
the presence or absence of the EMAC4SYNC feature.

The code has further been reworked where appropriate to use those macros
and inlines.

In addition, the register size passed to ioremap is now taken from the
device tree:

	c4 for EMAC4SYNC cores
	74 for EMAC4 cores
	70 for EMAC cores

rather than sizeof (emac_regs).

Finally, the device trees have been updated with the appropriate compatible
entries and resource sizes.

This has been tested on an AMCC Haleakala board such that: 1) inbound
ICMP requests to 'haleakala.local' via MDNS from both Mac OS X 10.4.11
and Ubuntu 8.04 systems as well as 2) outbound ICMP requests from
'haleakala.local' to those same systems in the '.local' domain via MDNS
now work.
Signed-off-by: NGrant Erickson <gerickson@nuovations.com>
Acked-by: NJeff Garzik <jgarzik@pobox.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This new file adds support for the ML507 reference design.  The ML507
uses the Virtex 5 FXT FPGA which embeds a ppc440 core.
Signed-off-by: NJohn Linn <john.linn@xilinx.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Added DMA nodes for the elo/elo-plus DMA engines.

Renamed the interrupt controller alias in mpc832x_rdb.dts to ipic so that
its the same as all the other boards.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This makes the sam440ep.dts dts-v1 compliant.
Signed-off-by: NGiuseppe Coviello <gicoviello@gmail.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

The Sam440ep is an high customizable general purpose mini-itx board,
based on the AMCC 440EP and with a LatticeXP FPGA onboard.

It's poduced by ACube Systems Srl (Bassano del Grappa, Italy),
http://www.acube-systems.biz.
Signed-off-by: NGiuseppe Coviello <gicoviello@gmail.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>