The irq_high stuff was mistakenly copied from mxc gpio driver.
The mxs gpio controller has only one irq line for each 32-pin
gpio port.  The patch remove irq_high related codes.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The gpio-mxs controller complies with basic_mmio_gpio library.  This
patch converts the driver to use the library.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The patch converts gpio-mxc driver to use generic irq chip.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Sort the gpio makefile and enforce the naming convention gpio-*.c for
gpio drivers.

v2: cleaned up filenames in Kconfig and comment blocks
v3: fixup use of BASIC_MMIO to GENERIC_GPIO for mxc
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The interrupt pin of the PCA953x is active low, and on the rising edge
no interrupt should be produced.
Signed-off-by: NDavid Jander <david@protonic.nl>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The GPIO driver should reside in drivers/gpio.

v3: Change Kconfig option to def_bool y
v2: Make the Kconfig symbol a silent option, dependent on ARCH_EP93XX
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The gpio-mxc controller complies with basic_mmio_gpio library.  The
patch convert the driver to use the library.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The patch makes necessary changes on gpio-mxc as below to turn it
into an upstanding gpio driver.

 * Add a list to save all mx2 ports references, so that
   mx2_gpio_irq_handler can walk through all interrupt status
   registers

 * Use readl/writel to replace mach-specific accessors
   __raw_readl/__raw_writel

 * Change mxc_gpio_init into mxc_gpio_probe function

 * Move "struct mxc_gpio_port" into gpio-mxc.c, as it needs not to
   be public at all, and also make some other cleanup on
   plat-mxc/include/mach/gpio.h at the same time

And the patch then migrates mach-imx and mach-mx5 to the updated
driver by adding corresponding platform devices.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NOlof Johansson <olof@lixom.net>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

GPIO drivers are getting moved to drivers/gpio for cleanup and
consolidation.  This patch moves the plat-mxc driver.  Follow up
patches will clean it up and make it a fine upstanding gpio driver.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The patch makes necessary changes on gpio-mxs as below to turn it
into an upstanding gpio driver.

 * Clean up the gpio port definition stuff

 * Use readl/writel to replace mach-specific accessors
   __raw_readl/__raw_writel

 * Change mxs_gpio_init into mxs_gpio_probe function

And it then migrates mach-mxs to the updated driver by adding
corresponding platform devices.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

GPIO drivers are getting moved to drivers/gpio for cleanup and
consolidation.  This patch moves the mxs driver.  Follow up patches
will clean it up and make it a fine upstanding example of a gpio
driver.

v2: Removed header file entirely and put struct definition directly
    into driver.  The struct isn't used anywhere else in the kernel.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Tested-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>

Al Viro observes that in the hugetlb case, handle_mm_fault() may return
a value of the kind ENOSPC when its caller is expecting a value of the
kind VM_FAULT_SIGBUS: fix alloc_huge_page()'s failure returns.
Signed-off-by: NHugh Dickins <hughd@google.com>
Acked-by: NAl Viro <viro@zeniv.linux.org.uk>
Cc: stable@kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: usb - turn off de-emphasis in s/pdif for cm6206
  ALSA: asihpi: Use angle brackets for system includes
  ALSA: fm801: add error handling if auto-detect fails
  ALSA: hda - Check pin support EAPD in ad198x_power_eapd_write
  ALSA: hda - Fix HP and Front pins of ad1988/ad1989 in ad198x_power_eapd()
  ALSA: 6fire: Don't leak firmware in error path
  ASoC: Fix wm_hubs input PGA ZC bits
  ASoC: Fix dapm_is_shared_kcontrol so everything isn't shared

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging:
  hwmon: (max6642): Better chip detection schema
  hwmon: (coretemp) Further relax temperature range checks
  hwmon: (coretemp) Fix TjMax detection for older CPUs
  hwmon: (coretemp) Relax target temperature range check
  hwmon: (max6642) Rename temp_fault sysfs attribute to temp2_fault

* 'for-linus' of git://android.git.kernel.org/kernel/tegra:
  ARM: Tegra: Harmony: Fix conflicting GPIO numbering

Currently, both the WM8903 and TPS6586x chips attempt to register with
gpiolib using the same GPIO numbers. This causes the audio driver to
fail to initialize.

To solve this, add a define to board-harmony.h for the TPS6586x, and make
board-harmony-power.c use this define, instead of directly referencing
TEGRA_NR_GPIOS.

This fixes a regression introduced by commit
6f168f2f.
ARM: tegra: harmony: initialize the TPS65862 PMIC
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NColin Cross <ccross@android.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable: (25 commits)
  btrfs: fix uninitialized variable warning
  btrfs: add helper for fs_info->closing
  Btrfs: add mount -o inode_cache
  btrfs: scrub: add explicit plugging
  btrfs: use btrfs_ino to access inode number
  Btrfs: don't save the inode cache if we are deleting this root
  btrfs: false BUG_ON when degraded
  Btrfs: don't save the inode cache in non-FS roots
  Btrfs: make sure we don't overflow the free space cache crc page
  Btrfs: fix uninit variable in the delayed inode code
  btrfs: scrub: don't reuse bios and pages
  Btrfs: leave spinning on lookup and map the leaf
  Btrfs: check for duplicate entries in the free space cache
  Btrfs: don't try to allocate from a block group that doesn't have enough space
  Btrfs: don't always do readahead
  Btrfs: try not to sleep as much when doing slow caching
  Btrfs: kill BTRFS_I(inode)->block_group
  Btrfs: don't look at the extent buffer level 3 times in a row
  Btrfs: map the node block when looking for readahead targets
  Btrfs: set range_start to the right start in count_range_bits
  ...

Improve detection of MAX6642 by reading non existing registers (0x04, 0x06
and 0xff). Reading those registers returns the previously read value.
Signed-off-by: NPer Dalen <per.dalen@appeartv.com>
[guenter.roeck@ericsson.com: added second set of register reads]
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
  [SCSI] Fix oops caused by queue refcounting failure

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (40 commits)
  tg3: Fix tg3_skb_error_unmap()
  net: tracepoint of net_dev_xmit sees freed skb and causes panic
  drivers/net/can/flexcan.c: add missing clk_put
  net: dm9000: Get the chip in a known good state before enabling interrupts
  drivers/net/davinci_emac.c: add missing clk_put
  af-packet: Add flag to distinguish VID 0 from no-vlan.
  caif: Fix race when conditionally taking rtnl lock
  usbnet/cdc_ncm: add missing .reset_resume hook
  vlan: fix typo in vlan_dev_hard_start_xmit()
  net/ipv4: Check for mistakenly passed in non-IPv4 address
  iwl4965: correctly validate temperature value
  bluetooth l2cap: fix locking in l2cap_global_chan_by_psm
  ath9k: fix two more bugs in tx power
  cfg80211: don't drop p2p probe responses
  Revert "net: fix section mismatches"
  drivers/net/usb/catc.c: Fix potential deadlock in catc_ctrl_run()
  sctp: stop pending timers and purge queues when peer restart asoc
  drivers/net: ks8842 Fix crash on received packet when in PIO mode.
  ip_options_compile: properly handle unaligned pointer
  iwlagn: fix incorrect PCI subsystem id for 6150 devices
  ...

With Linus' tree, today's linux-next build (powercp ppc64_defconfig)
produced this warning:

fs/btrfs/delayed-inode.c: In function 'btrfs_delayed_update_inode':
fs/btrfs/delayed-inode.c:1598:6: warning: 'ret' may be used
uninitialized in this function

Introduced by commit 16cdcec7 ("btrfs: implement delayed inode items
operation").

This fixes a bug in btrfs_update_inode(): if the returned value from
btrfs_delayed_update_inode is a nonzero garbage, inode stat data are not
updated and several call paths may hit a BUG_ON or fail with strange
code.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NDavid Sterba <dsterba@suse.cz>

wrap checking of filesystem 'closing' flag and fix a few missing memory
barriers.
Signed-off-by: NDavid Sterba <dsterba@suse.cz>

This makes the inode map cache default to off until we
fix the overflow problem when the free space crcs don't fit
inside a single page.
Signed-off-by: NChris Mason <chris.mason@oracle.com>

With the removal of the implicit plugging scrub ends up doing more and
smaller I/O than necessary. This patch adds explicit plugging per chunk.
Signed-off-by: NArne Jansen <sensille@gmx.net>
Signed-off-by: NChris Mason <chris.mason@oracle.com>

commit 4cb5300b ("Btrfs: add mount -o auto_defrag") accesses inode
number directly while it should use the helper with the new inode
number allocator.
Signed-off-by: NDavid Sterba <dsterba@suse.cz>
Signed-off-by: NChris Mason <chris.mason@oracle.com>

With xfstest 254 I can panic the box every time with the inode number caching
stuff on.  This is because we clean the inodes out when we delete the subvolume,
but then we write out the inode cache which adds an inode to the subvolume inode
tree, and then when it gets evicted again the root gets added back on the dead
roots list and is deleted again, so we have a double free.  To stop this from
happening just return 0 if refs is 0 (and we're not the tree root since tree
root always has refs of 0).  With this fix 254 no longer panics.  Thanks,
Signed-off-by: NJosef Bacik <josef@redhat.com>
Tested-by: NDavid Sterba <dsterba@suse.cz>
Signed-off-by: NChris Mason <chris.mason@oracle.com>

In degraded mode the struct btrfs_device of missing devs don't have
device->name set. A kstrdup of NULL correctly returns NULL. Don't
BUG in this case.
Signed-off-by: NArne Jansen <sensille@gmx.net>
Signed-off-by: NChris Mason <chris.mason@oracle.com>

This adds extra checks to make sure the inode map we are caching really
belongs to a FS root instead of a special relocation tree.  It
prevents crashes during balancing operations.
Signed-off-by: NLiu Bo <liubo2009@cn.fujitsu.com>
Signed-off-by: NChris Mason <chris.mason@oracle.com>

The free space cache uses only one page for crcs right now,
which means we can't have a cache file bigger than the
crcs we can fit in the first page.  This adds a check to
enforce that restriction.
Signed-off-by: NChris Mason <chris.mason@oracle.com>

The nitems counter needs to start at zero
Signed-off-by: NChris Mason <chris.mason@oracle.com>

The current scrub implementation reuses bios and pages as often as possible,
allocating them only on start and releasing them when finished. This leads
to more problems with the block layer than it's worth. The elevator gets
confused when there are more pages added to the bio than bi_size suggests.
This patch completely rips out the reuse of bios and pages and allocates
them freshly for each submit.
Signed-off-by: NArne Jansen <sensille@gmx.net>
Signed-off-by: NChris Maosn <chris.mason@oracle.com>

* 'for-linus' of git://git.kernel.dk/linux-block:
  block: Use hlist_entry() for io_context.cic_list.first
  cfq-iosched: Remove bogus check in queue_fail path
  xen/blkback: potential null dereference in error handling
  xen/blkback: don't call vbd_size() if bd_disk is NULL
  block: blkdev_get() should access ->bd_disk only after success
  CFQ: Fix typo and remove unnecessary semicolon
  block: remove unwanted semicolons
  Revert "block: Remove extra discard_alignment from hd_struct."
  nbd: adjust 'max_part' according to part_shift
  nbd: limit module parameters to a sane value
  nbd: pass MSG_* flags to kernel_recvmsg()
  block: improve the bio_add_page() and bio_add_pc_page() descriptions

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin:
  Blackfin: strncpy: fix handling of zero lengths

* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
  asm-generic/unistd.h: support sendmmsg syscall
  tile: enable CONFIG_BUGVERBOSE

* 'linux-next' of git://git.infradead.org/ubifs-2.6:
  UBIFS: fix-up free space earlier
  UBIFS: intialize LPT earlier
  UBIFS: assert no fixup when writing a node
  UBIFS: fix clean znode counter corruption in error cases
  UBIFS: fix memory leak on error path
  UBIFS: fix shrinker object count reports
  UBIFS: fix recovery broken by the previous recovery fix
  UBIFS: amend ubifs_recover_leb interface
  UBIFS: introduce a "grouped" journal head flag
  UBIFS: supress false error messages

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-2.6-ktest:
  ktest: Ignore unset values of the minconfig in config_bisect
  ktest: Fix result of rebooting the kernel
  ktest: Fix off-by-one in config bisect result

Merge branch 'rmobile-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6

* 'rmobile-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
  ARM: mach-shmobile: add DMAC clock definitions on SH7372
  ARM: arch-shmobile: support SDHI card detection on mackerel, using a GPIO
  sh_mobile_meram: MERAM platform data for LCDC