This moves the shared regulatory structure into the
common structure. We will use this ongoing for common
data.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In ath9k_stop(), tx_complete_work was being cancelled twice.
This patch fixes it. Also, locking sc->mutex should be done
at the beginning.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After initial power-up, the embedded cpu is usually halted.  However,
if we down the interface and only do a soft reset before bringing
the interface back up, it will still be running and the firmware
loading code will bail out.  This change halts the CPU before loading
the firmware, enabling a second call to wl1251_boot() to succeed
without a hard reset.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rt2800pci can handle different retry rates,
it will always step 1 rate down after a failed
transmission so creating the retry rate list
for mac80211 is quite simple.
Signed-off-by: NBenoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

According to the original Ralink driver,
LG_FBK_CFG0_OFDMMCS2FBK should be initialized to 9 rather then 3.

Based on a patch for rt2800pci from Benoit
Signed-off-by: NBenoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the TX descriptor the Packet ID must not be 0,
so add 1 to the ID. The wireless CLI ID is not allowed
to be 0 either, but also must be initialized with the
wcid value rather then keyid.

Based on a patch for rt2800pci from Benoit
Signed-off-by: NBenoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the RX descriptor indicates the frame was L2 padded,
the SKBDESC_L2_PADDED flag should be set to make sure the
L2 padding is removed before it is send to mac80211.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add new defines for RF chipsets which can be found
by the driver. We don't have to check for these
chips specifically yet, but it is better to have
the defines in now.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fixed comments about SHARED_KEY_TABLE_BASE and SHARED_KEY_MODE_BASE.
Fixed initialization loop for SHARED_KEY_MODE_ENTRY.

Based on a patch for rt2800pci from Benoit.
Signed-off-by: NBenoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The rfkill_poll callback function in the drivers check a bit
to see if the RFKILL key has been pressed. However when the
bit is set it means the radio is active and the device can be
used.

The wiphy_rfkill_set_hw_state() function expects the inversed,
so '1' must be send when the radio must be disabled.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Call set_tx_power_control with a LPPHY_TXPCTL rather than an
LPPHY_TX_PWR_CTL_CMD_MODE.
Signed-off-by: NGábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Check the mode the hardware is in, not the mode we used the last time.
Signed-off-by: NGábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ACX_SLV_SOFT_RESET_BIT and ACX_REG_EEPROM_START_BIT are both defined
as "1" in the vendor driver code, but they were defined to be BIT(1)
("2") here.

The SOFT_RESET typo ensures that wl1251_boot_soft_reset() doesn't;
as a result the device hangs when trying to reprogram the PLL
registers while running.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Acked-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

All but two drivers have now stopped using the two
deprecated members radio_enabled and beacon_int,
so it's about time to remove them for good.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: NKalle Valo <kalle.valo@iki.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Over time, a whole bunch of drivers have come up
with their own scheme to delay the configure_filter
operation to a workqueue. To be able to simplify
things, allow configure_filter to sleep, and add
a new prepare_multicast callback that drivers that
need the multicast address list implement. This new
callback must be atomic, but most drivers either
don't care or just calculate a hash which can be
done atomically and then uploaded to the hardware
non-atomically.

A cursory look suggests that at76c50x-usb, ar9170,
mwl8k (which is actually very broken now), rt2x00,
wl1251, wl1271 and zd1211 should make use of this
new capability.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Larry has reported success getting scan data with an LP-PHY device,
so it's probably time to release LP-PHY support for testing.

Also disable 802.11a support for now, as 802.11a currently causes
the driver to panic on startup (NULL pointer dereference).
Signed-off-by: NGábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The spec for initializing the B2062 radio have changed recently,
update the code to match the changes.
Signed-off-by: NGábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I missed the "+16" part of the instruction in the specs.
Signed-off-by: NGábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A few typos have been discovered in both the specs and the code.
This patch fixes them.

Also use lpphy_op_switch_channel consistently, and make all users
of it print its return value for easier debugging.
Signed-off-by: NGábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The channel switch routine had a whole instruction missing. Add it.
Signed-off-by: NGábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The spec had some nasty typos, and a large part of the rev0/1 BB
init procedure was also missing. Fix these.

Also make the init-time channel switch debuggable.

(The change from -EINVAL to -EIO is simply to make it possible
to distinguish the PLL charge pump error from a channel-not-found
error.)
Signed-off-by: NGábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Don't drop all packets received from an LP-PHY with WARN_ON.
Also update a comment with LP-specific information.
Signed-off-by: NGábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This should fix the remaining WARN_ON.
Signed-off-by: NGábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NGábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Rev2+ never needs to have gain tables adjusted according to the spec.
Signed-off-by: NGábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

-Enable rate memory init for LP-PHY (same as G and N-PHY).
-Mark rev.2 LP-PHYs with the B2063 radio as supported.
-Allow using the 5GHz band on LP-PHYs.
Signed-off-by: NGábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add support for loading LP-PHY firmware to b43_try_request_fw.
Signed-off-by: NGábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Johannes kindly pointed out that I completely missed a hunk in
his patch: "[PATCH] cfg80211: allow driver to override PS default".

The driver must explicitly set ps_default to false,
as the setting is pre-filled with the kconfig default.
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enable AsyncFIFO and AGGWEP for AR9287_12 and later revisions only.
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

-Move pdiv from lpphy_2062_init to struct b43_phy_lp.
-Add channel table for the B2062 radio.
-Add code for tuning the B2062 radio to channel.
-Add error handling to op_switch_channel, and use it for both radios.

Rev0/1/B2062 will now hopefully show some signs of life, though
it won't work at full performance, as calibration is still missing.
Signed-off-by: NGábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Rev.2+/B2063 will now hopefully show some signs of life, though
it won't work at full performance, as calibration is still missing.
Signed-off-by: NGábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

sparse complains about a bad constant expression due to the use of a
dynamic-sized array in get_common_rates().  Allocate and free the array
instead.
Signed-off-by: NAndrey Yurovsky <andrey@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Unfortunately, PS currently affects RX performance
significantly enough to warrant disabling it by
default, but give the user the choice to enable it
again with iwconfig.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The field called 'len' in struct iwl_rx_packet is in fact not just a length
field but also includes some flags from the flow handler.  In several places
throughout the driver, this causes incorrect values to be interpreted as
lengths when the field is improperly masked.

In most situations the improper use is for debugging output, and simply results
in an erroneous message, such as:

[551933.070224] ieee80211 phy0: I iwl_rx_statistics Statistics notification received (480 vs -1367342620).

which should read '(480 vs 484)'.

In at least one case this could case bad things to happen:

void iwl_rx_pm_debug_statistics_notif(struct iwl_priv *priv,
                                      struct iwl_rx_mem_buffer *rxb)
{
        struct iwl_rx_packet *pkt = (struct iwl_rx_packet *)rxb->skb->data;
        IWL_DEBUG_RADIO(priv, "Dumping %d bytes of unhandled "
                        "notification for %s:\n",
                        le32_to_cpu(pkt->len), get_cmd_string(pkt->hdr.cmd));
        iwl_print_hex_dump(priv, IWL_DL_RADIO, pkt->u.raw, le32_to_cpu(pkt->len)
);
}
EXPORT_SYMBOL(iwl_rx_pm_debug_statistics_notif);

Given the rampant misuse of this field without proper masking throughout the
driver (every use but one), this patch renames the field from 'len' to
'len_n_flags' to reduce confusion.  It also adds the proper masking when
this field is used as a length value.
Signed-off-by: NDaniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Adding legacy thermal throttling management support to 5150 NIC
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Green-field mode should be configured in the HT station table.  This patch uses
both the per-station GF support flag as well as the current BSS HT operation
mode (non-GF stations present flag).

Added the "ht_greenfield_support" field to struct iwl_cfg to replace the
device-specific check in rs_use_green().  That check has been moved to
iwlcore_init_ht_hw_capab().
Signed-off-by: NDaniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>