Commit 5143c953 ("mmc: sdhci-esdhc-imx: Allow all supported
prescaler values") made it possible to set SYSCTL.SDCLKFS to 0 in SDR
mode, thus bypassing the SD clock frequency prescaler, in order to be
able to get higher SD clock frequencies in some contexts. However, that
commit missed the fact that this value is illegal on the eSDHCv3
instance of the i.MX53. This seems to be the only exception on i.MX,
this value being legal even for the eSDHCv2 instances of the i.MX53.

Fix this issue by changing the minimum prescaler value if the i.MX53
eSDHCv3 is detected. According to the i.MX53 reference manual, if
DLLCTRL[10] can be set, then the controller is eSDHCv3, else it is
eSDHCv2.

This commit fixes the following issue, which was preventing the i.MX53
Loco (IMX53QSB) board from booting Linux 4.15.0-rc5:
[    1.882668] mmcblk1: error -84 transferring data, sector 2048, nr 8, cmd response 0x900, card status 0xc00
[    2.002255] mmcblk1: error -84 transferring data, sector 2050, nr 6, cmd response 0x900, card status 0xc00
[   12.645056] mmc1: Timeout waiting for hardware interrupt.
[   12.650473] mmc1: sdhci: ============ SDHCI REGISTER DUMP ===========
[   12.656921] mmc1: sdhci: Sys addr:  0x00000000 | Version:  0x00001201
[   12.663366] mmc1: sdhci: Blk size:  0x00000004 | Blk cnt:  0x00000000
[   12.669813] mmc1: sdhci: Argument:  0x00000000 | Trn mode: 0x00000013
[   12.676258] mmc1: sdhci: Present:   0x01f8028f | Host ctl: 0x00000013
[   12.682703] mmc1: sdhci: Power:     0x00000002 | Blk gap:  0x00000000
[   12.689148] mmc1: sdhci: Wake-up:   0x00000000 | Clock:    0x0000003f
[   12.695594] mmc1: sdhci: Timeout:   0x0000008e | Int stat: 0x00000000
[   12.702039] mmc1: sdhci: Int enab:  0x107f004b | Sig enab: 0x107f004b
[   12.708485] mmc1: sdhci: AC12 err:  0x00000000 | Slot int: 0x00001201
[   12.714930] mmc1: sdhci: Caps:      0x07eb0000 | Caps_1:   0x08100810
[   12.721375] mmc1: sdhci: Cmd:       0x0000163a | Max curr: 0x00000000
[   12.727821] mmc1: sdhci: Resp[0]:   0x00000920 | Resp[1]:  0x00000000
[   12.734265] mmc1: sdhci: Resp[2]:   0x00000000 | Resp[3]:  0x00000000
[   12.740709] mmc1: sdhci: Host ctl2: 0x00000000
[   12.745157] mmc1: sdhci: ADMA Err:  0x00000001 | ADMA Ptr: 0xc8049200
[   12.751601] mmc1: sdhci: ============================================
[   12.758110] print_req_error: I/O error, dev mmcblk1, sector 2050
[   12.764135] Buffer I/O error on dev mmcblk1p1, logical block 0, lost sync page write
[   12.775163] EXT4-fs (mmcblk1p1): mounted filesystem without journal. Opts: (null)
[   12.782746] VFS: Mounted root (ext4 filesystem) on device 179:9.
[   12.789151] mmcblk1: response CRC error sending SET_BLOCK_COUNT command, card status 0x900
Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Reported-by: NWladimir J. van der Laan <laanwj@gmail.com>
Tested-by: NWladimir J. van der Laan <laanwj@gmail.com>
Fixes: 5143c953 ("mmc: sdhci-esdhc-imx: Allow all supported prescaler values")
Cc: <stable@vger.kernel.org> # v4.13+
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

mmc clock can be stopped during runtime suspend and restart during runtime
resume if the sdio irq is not enabled. Stop sdio clock reduce EMI of
the device when the bus is not in use.
Signed-off-by: NMichael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

runtime_resume() should re-enable the clocks in reverse order comparing with
runtime_suspend()
Signed-off-by: NMichael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

We need to return in case of error even if the actual implementation
of sdhci_runtime_suspend_host always return 0. We don't want to
power down the clock and the assuption is that the sdhci_runtime_suspend_host
always let the system consistent in case of failure
Signed-off-by: NMichael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The SDHCI_QUIRK_NO_MULTIBLOCK quirk was used as a workaround for the
ENGcm07207 erratum. However, it caused excruciatingly slow SD transfers
(300 kB/s on average), and this erratum actually does not imply that
multiple-block transfers are not supported, so this was overkill.

The suggested workaround for this erratum is to set SYSCTL.RSTA, but the
simple DAT line software reset (which resets the DMA circuit among
others) triggered by sdhci_finish_data() in case of errors seems to be
sufficient. Indeed, generating errors in a controlled manner on i.MX25
using the FEVT register right in the middle of read data transfers
without this quirk shows that nothing is written to the buffer by the
eSDHC past CMD12, and no extra Auto CMD12 is sent with AC12EN set, so
the data transfers on AHB are properly aborted. For write data
transfers, neither extra data nor extra Auto CMD12 is sent, as expected.
Moreover, after intensive stress tests on i.MX25, removing
SDHCI_QUIRK_NO_MULTIBLOCK seems to be safe.

SDHCI_QUIRK_BROKEN_ADMA has nothing to do with ENGcm07207, so set
ESDHC_FLAG_ERR004536 for the devices that had ESDHC_FLAG_ENGCM07207 set
in order to continue getting SDHCI_QUIRK_BROKEN_ADMA.
Signed-off-by: NBenoît Thébaudeau <benoit@wsystem.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

On i.MX, SYSCTL.SDCLKFS may always be set to 0 in order to make the SD
clock frequency prescaler divide by 1 in SDR mode, even with the eSDHC.
The previous minimum prescaler value of 2 in SDR mode with the eSDHC was
a code remnant from PowerPC, which actually has this limitation on
earlier revisions.

In DDR mode, the prescaler can divide by up to 512.

The maximum SD clock frequency in High Speed mode is 50 MHz. On i.MX25,
this change makes it possible to get 48 MHz from the USB PLL
(240 MHz / 5 / 1) instead of only 40 MHz from the USB PLL
(240 MHz / 3 / 2) or 33.25 MHz from the AHB clock (133 MHz / 2 / 2).
Signed-off-by: NBenoît Thébaudeau <benoit@wsystem.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

On i.MX25, the eSDHC DAT line software reset (SYSCTL.RSTD) unexpectedly
clears at least the data transfer width (PROCTL.DTW), which then results
in data CRC errors. This behavior is not documented, but it has actually
been observed. Consequently, the DAT line software resets triggered by
sdhci.c in case of errors caused unrecoverable errors.

Fix this by making sure that the DAT line software reset does not alter
the Host Control register. This behavior being undocumented, it may also
be present on other i.MX SoCs, so apply this fix for the whole i.MX
family.
Signed-off-by: NBenoît Thébaudeau <benoit@wsystem.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Fix various English mistakes and typos in comments and in printed
strings.
Signed-off-by: NBenoît Thébaudeau <benoit@wsystem.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

clk_prepare_enable() may fail, so we should better check its return value
and propagate it in the case of error.
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

USDHC tuning circuit should be reset before every time card enumeration
or re-enumeration.

SD3.0 card need tuning. For SDR104 card, when system suspend in standby
mode, and then resume back, the IO timing is still SDR104(tuned) which
may result in card re-enumeration fail in low card speed(400khz) for some
cards. And we did meet the issue that in certain probability, SDR104
card meet mmc command CRC/Timeout error when send CMD2 during mmc bus
resume.

This patch reset the tuning circuit when the ios timing is
MMC_TIMING_LEGACY/MMC_TIMING_MMC_HS/MMC_TIMING_SD_HS, which means both
mmc_power_up() and mmc_power_off() will reset the tuning circuit.
Signed-off-by: NHaibo Chen <haibo.chen@nxp.com>
Acked-by: NDong Aisheng <aisheng.dong@nxp.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Devices might save and restore tuning values so that re-tuning might not be
needed after a pm transition.  Let drivers decide by pushing the
mmc_retune_needed() logic down to them.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NLudovic Desroches <ludovic.desroches@microchip.com>

Currently for DDR50 card, it need tuning in default. We meet tuning fail
issue for DDR50 card and some data CRC error when DDR50 sd card works.

This is because the default pad I/O drive strength can't make sure DDR50
card work stable. So increase the pad I/O drive strength for DDR50 card,
and use pins_100mhz.

This fixes DDR50 card support for IMX since DDR50 tuning was enabled from
commit 9faac7b9 ("mmc: sdhci: enable tuning for DDR50")
Tested-and-reported-by: NTim Harvey <tharvey@gateworks.com>
Signed-off-by: NHaibo Chen <haibo.chen@nxp.com>
Cc: stable@vger.kernel.org # v4.4+
Acked-by: NDong Aisheng <aisheng.dong@nxp.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

- The DMA error interrupt bit is in a different position as
   compared to the sdhci standard.  This is accounted for in
   many cases, but not handled in the case of clearing the
   INT_STATUS register by writing a 1 to that location.
 - The HOST_CONTROL register is very different as compared to
   the sdhci standard.  This is accounted for in the write
   case, but not when read back out (which it is in the sdhci
   code).
Signed-off-by: NDave Russell <david.russell@datasoft.com>
Signed-off-by: NAaron Brice <aaron.brice@datasoft.com>
Acked-by: NDong Aisheng <aisheng.dong@nxp.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

i.MX USDHC Reference Manual has a mistake, for the register SYS_CTRL,
the DTOCV(bit 19~16) means the data timeout counter value. When DTOCV
is set to 0xF, it means SDCLK << 29, not SDCLK << 28.
Signed-off-by: NHaibo Chen <haibo.chen@nxp.com>
Acked-by: NDong Aisheng <aisheng.dong@nxp.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Now, when call esdhc_set_timeout() to set the data timeout counter value,
IPP_RST_N(bit 23) is wrongly affected. This patch add a mask to avoid this.
Signed-off-by: NHaibo Chen <haibo.chen@nxp.com>
Acked-by: NDong Aisheng <aisheng.dong@nxp.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

To prepare to make the sdhci_pltfm_suspend|resume() static functions, move
sdhci-esdhc-imx over to use the sdhci_suspend|resume_host().
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NDong Aisheng <aisheng.dong@nxp.com>

The system PM callbacks isn't used unless CONFIG_PM_SLEEP is set, thus it
triggers a compiler warning about unused functions. Avoid this by changing
from CONFIG_PM to CONFIG_PM_SLEEP.
Reported-by: NArnd Bergmann <arnd@arndb.de>
Fixes: b70d0b3b5b29 ("mmc: sdhci-esdhc-imx: add esdhc specific suspend resume callback")
Cc: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NDong Aisheng <aisheng.dong@nxp.com>

The tuning bits like FBCLK_SEL, SMP_CLK_SEL and DLY_CELL which affects
timing may have already been set by ROM if booting from SD3.0 mode like
SDR104. Let's clear it first during driver probe before doing the new
card enumeration to avoid working on the wrong timing.

Note that tuning bits are dynamical settings which may need to be kept
during MMC_PM_KEEP_POWER suspend, so we did not put them into hwinit
function.
Signed-off-by: NDong Aisheng <aisheng.dong@nxp.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

sdhci_esdhc_imx_hwinit() includes all basic hw intialization.
Calling it after resume to re-initialize hw in case its state
is already lost in low power mode.
Signed-off-by: NDong Aisheng <aisheng.dong@nxp.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Move tuning static configuration into basic hwinit function.
Tuning configuration may also be lost in low power mode, so
need restore in hwinit().
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NDong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Move all hw related static initializations into a separate function
which helps concentrate the hw related initialization code.
And that function could also be called by other places later as a
basic hw state restore.
e.g. suspend/resume where the hw state is possible to lost due to
low power mode.
Signed-off-by: NDong Aisheng <aisheng.dong@nxp.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

When enable DDR, the clock factor definition is changed.
e.g. original 200Mhz will become 100Mhz once MIX_CTRL_DDREN bit is set
So we need to update the clock setting then the strobe dll can lock
the correct clock rate.

Additionally we also need disable the clock before locking strobe dll.
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NDong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Indicating hw auto retuning support for mx6qdl in the fake caps_1
register and enable auto retuning in post_tuning process after
tuning completes.
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NDong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Enable HW auto retuning when set SDHCI_CTRL_EXEC_TUNING and clear it
when clear SDHCI_CTRL_TUNED_CLK.
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NDong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The delay cells of some SoCs may have less delay per one cell,
for such SoCs, user could set the start delay cell point to bypass
the first a few meaningless tuning commands.
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NDong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Disable DLL delay line settings explicitly during driver initialization
in case ROM/uBoot had set an invalid delay.
e.g. MX6DL ROM has set the default delay line(DLLCTRL) to 0x1000021,
the uSDHC clock timing will become marginal when works on DDR mode
due to default delay and will possibly see CRC errors in case the board
is not perfectly designed on the eMMC chip layout.
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NDong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Currently, we config the watermark_level register only in probe.
This will cause the mmc write operation timeout issue after system
resume back in LPSR mode. Because in LPSR mode, after system resume
back, the watermark_level register(0x44) changes to 0x08000880, which
set the write watermark level as 0, and set the read watermark level
as 128. This value is incorrect.

This patch restores the setting of watermark level register after
system resume back.
Signed-off-by: NDong Aisheng <aisheng.dong@nxp.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

It will be used for platform specific suspend/resume state save/restore
work for some low power mode like Mega/Fast or LPSR mode.
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NDong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The driver has already implemented the private .set_timeout()
callback for common SDHCI code to do correct timeout value setting,
it does not need call sdhci_calc_timeout(), so this quirk actually
is not working. Remove it now.
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NDong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Most users of IS_ERR_VALUE() in the kernel are wrong, as they
pass an 'int' into a function that takes an 'unsigned long'
argument. This happens to work because the type is sign-extended
on 64-bit architectures before it gets converted into an
unsigned type.

However, anything that passes an 'unsigned short' or 'unsigned int'
argument into IS_ERR_VALUE() is guaranteed to be broken, as are
8-bit integers and types that are wider than 'unsigned long'.

Andrzej Hajda has already fixed a lot of the worst abusers that
were causing actual bugs, but it would be nice to prevent any
users that are not passing 'unsigned long' arguments.

This patch changes all users of IS_ERR_VALUE() that I could find
on 32-bit ARM randconfig builds and x86 allmodconfig. For the
moment, this doesn't change the definition of IS_ERR_VALUE()
because there are probably still architecture specific users
elsewhere.

Almost all the warnings I got are for files that are better off
using 'if (err)' or 'if (err < 0)'.
The only legitimate user I could find that we get a warning for
is the (32-bit only) freescale fman driver, so I did not remove
the IS_ERR_VALUE() there but changed the type to 'unsigned long'.
For 9pfs, I just worked around one user whose calling conventions
are so obscure that I did not dare change the behavior.

I was using this definition for testing:

 #define IS_ERR_VALUE(x) ((unsigned long*)NULL == (typeof (x)*)NULL && \
       unlikely((unsigned long long)(x) >= (unsigned long long)(typeof(x))-MAX_ERRNO))

which ends up making all 16-bit or wider types work correctly with
the most plausible interpretation of what IS_ERR_VALUE() was supposed
to return according to its users, but also causes a compile-time
warning for any users that do not pass an 'unsigned long' argument.

I suggested this approach earlier this year, but back then we ended
up deciding to just fix the users that are obviously broken. After
the initial warning that caused me to get involved in the discussion
(fs/gfs2/dir.c) showed up again in the mainline kernel, Linus
asked me to send the whole thing again.

[ Updated the 9p parts as per Al Viro  - Linus ]
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lkml.org/lkml/2016/1/7/363
Link: https://lkml.org/lkml/2016/5/27/486
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> # For nvmem part
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit 0e748234 ("mmc: sdhci: Add size for caller in init+register")
allows users of sdhci_pltfm to allocate private space in calls to
sdhci_pltfm_init+sdhci_pltfm_register. This patch migrates the sdhci
esdhc-imx driver to this allocation.
Signed-off-by: NJisheng Zhang <jszhang@marvell.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Here we use '|=' to set the tuning-step, but before that, we should
clear the tuning-step, otherwise we could got the wrong setting.
Signed-off-by: NHaibo Chen <haibo.chen@freescale.com>
Acked-by: NDong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The mmc_execute_tuning() has already prepared the opcode,
there is no need to prepare it again at mmc_send_tuning(),
and, there is a BUG of mmc_send_tuning() to determine the opcode
by bus width, assume eMMC was running at HS200, 4bit mode,
then the mmc_send_tuning() will overwrite the opcode from CMD21
to CMD19, then got error.

in addition, extend an argument of "cmd_error" to allow getting
if there was cmd error when tune response.
Signed-off-by: NChaotian Jing <chaotian.jing@mediatek.com>
[Ulf: Rebased patch]
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

By default, for all imx SoC types, the watermark level is 16, and the
burst length is 8. But if the SDIO/SD/MMC I/O speed is fast enough,
this default watermark level and burst length will be the performance
bottleneck.

For example, i.MX7D support eMMC HS400 mode, this mode can run in 8 bit,
200MHZ DDR mode. So the I/O speed improve a lot compare to SD3.0.
The default burst length is 8, if we don't change this value, in
HS400 mode, when we do eMMC read operation, we can find that the
clock signal will stop for a period of time. This means the speed
of data moving on AHB bus is slower than I/O speed. So we should
improve the speed of data moving on AHB bus.

This patch set the default burst length as 16, and set the default
watermark level as 64. The test result is the clock signal has
no stop during the eMMC HS400 operation.
Signed-off-by: NHaibo Chen <haibo.chen@freescale.com>
Acked-by: NDong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Currently we find that if a usdhc is choosed to boot system, then ROM
code will set the burst length enable bit of this usdhc as 0.

This will make performance drop a lot if this usdhc's burst length is
configed. So this patch set back the burst_length_enable bit as 1,
which is the default value, and means burst length is enabled for INCR.
Signed-off-by: NHaibo Chen <haibo.chen@freescale.com>
Acked-by: NDong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

tuning-step is the delay cell steps in tuning procedure. The default value
of tuning-step is 1. Some boards or cards need another value to pass the
tuning procedure. For example, imx7d-sdb board need the tuning-step value
as 2, otherwise it can't pass the tuning procedure.

So this patch add the tuning-step setting in driver, so that user can set
the tuning-step value in dts.
Signed-off-by: NHaibo Chen <haibo.chen@freescale.com>
Acked-by: NDong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The imx7d usdhc is derived from imx6sx, the difference is that
imx7d support HS400.

So introduce a new compatible string for imx7d and add HS400
support for imx7d usdhc.
Signed-off-by: NHaibo Chen <haibo.chen@freescale.com>
Acked-by: NDong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

After commit 8d86e4fc ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()"),
it's not used anymore.
Signed-off-by: NDong Aisheng <aisheng.dong@freescale.com>
Reviewed-by: NJohan Derycke <johan.derycke@barco.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

After commit 8d86e4fc ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()"),
we do not need those duplicated parsing anymore.

Note: fsl,cd-controller is also deleted due to the driver does
not support controller card detection anymore after switch to runtime pm.
And there's no user of it right now in device tree.

wp-gpios is kept because we're still support fsl,wp-controller,
so we need a way to check if it's gpio wp or controller wp.
Signed-off-by: NDong Aisheng <aisheng.dong@freescale.com>
Reviewed-by: NJohan Derycke <johan.derycke@barco.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This is an incremental fix of commit
e62bd351b("mmc: sdhci-esdhc-imx: Do not break platform data boards").

After commit 8d86e4fc ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()"),
we do not need to run the check of boarddata->wp_type/cd_type/max_bus_width
again for dt platform since those are already handled by mmc_of_parse().

Current code only exclude the checking of wp_type for dt platform which
does not make sense.

This patch moves all non dt probe code into one function.
Besides, since we only support SD3.0/eMMC HS200 for dt platform, the
support_vsel checking and ultra high speed pinctrl state are also merged
into sdhci_esdhc_imx_probe_dt.

Then we have two separately probe function for dt and non dt type.
This can make the driver probe more clearly.
Signed-off-by: NDong Aisheng <aisheng.dong@freescale.com>
Reviewed-by: NJohan Derycke <johan.derycke@barco.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>