Rather than open-coding our own check, use irq_has_action()
to check if an irq has an action - ie. is "in use".

irq_has_action() doesn't take the descriptor lock, but it
shouldn't matter - we're just using it as an indicator
that the irq is in use. disable_irq_nosync() will take
the descriptor lock before doing anything also.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Based on PCI Express AER specs, a root port might receive multiple
TLP errors while it could only save a correctable error source id
and an uncorrectable error source id at the same time. In addition,
some root port hardware might be unable to provide a correct source
id, i.e., the source id, or the bus id part of the source id provided
by root port might be equal to 0.

The patchset implements the support in kernel by searching the device
tree under the root port.

Patch 1 changes parameter cb of function pci_walk_bus to return a value.
When cb return non-zero, pci_walk_bus stops more searching on the
device tree.
Reviewed-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NZhang Yanmin <yanmin_zhang@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

While adding native EEH support to Emulex and Qlogic drivers, it was
discovered that dev->error_state was set to pci_io_channel_normal too
late in the recovery process. These drivers rely on error_state to
determine if they can access the device in their slot_reset callback,
thus error_state needs to be set to pci_io_channel_normal in
eeh_report_reset(). Below is a detailed explanation (courtesy of Richard
Lary) as to why this is necessary.

Background:
PCI MMIO or DMA accesses to a frozen slot generate additional EEH
errors. If the number of additional EEH errors exceeds EEH_MAX_FAILS the
adapter will be shutdown. To avoid triggering excessive EEH errors and
an undesirable adapter shutdown, some drivers use the
pci_channel_offline(dev) wrapper function to return a Boolean value
based on the value of pci_dev->error_state to determine if PCI MMIO or
DMA accesses are safe. If the wrapper returns TRUE, drivers must not
make PCI MMIO or DMA access to their hardware.

The pci_dev structure member error_state reflects one of three values,
1) pci_channel_io_normal, 2) pci_channel_io_frozen, 3)
pci_channel_io_perm_failure.  Function pci_channel_offline(dev) returns
TRUE if error_state is pci_channel_io_frozen or pci_channel_io_perm_failure.

The EEH driver sets pci_dev->error_state to pci_channel_io_frozen at the
point where the PCI slot is frozen. Currently, the EEH driver restores
dev->error_state to pci_channel_io_normal in eeh_report_resume() before
calling the driver's resume callback. However, when the EEH driver calls
the driver's slot_reset callback() from eeh_report_reset(), it
incorrectly indicates the error state is still pci_channel_io_frozen.

Waiting until eeh_report_resume() to restore dev->error_state to
pci_channel_io_normal is too late for Emulex and QLogic FC drivers and
any other drivers which are designed to use common code paths in these
two cases: i) those called after the driver's slot_reset callback() and
ii) those called after the PCI slot is frozen but before the driver's
slot_reset callback is called. Case i) all driver paths executed to
reinitialize the hardware after a reset and case ii) all code paths
executed by driver kernel threads that run asynchronous to the main
driver thread, such as interrupt handlers and worker threads to process
driver work queues.

Emulex and QLogic FC drivers are designed with common code paths which
require that pci_channel_offline(dev) reflect the true state of the
hardware. The state transitions that the hardware takes from Normal
Operations to Slot Frozen to Reset to Normal Operations are documented
in the Power Architecture™ Platform Requirements+ (PAPR+) in Table 75.
PE State Control.

PAPR defines the following 3 states:

0 -- Not reset, Not EEH stopped, MMIO load/store allowed, DMA allowed
     (Normal Operations)
1 -- Reset, Not EEH stopped, MMIO load/store disabled, DMA disabled
2 -- Not reset, EEH stopped, MMIO load/store disabled, DMA disabled
     (Slot Frozen)

An EEH error places the slot in state 2 (Frozen) and the adapter driver
is notified that an EEH error was detected. If the adapter driver
returns PCI_ERS_RESULT_NEED_RESET, the EEH driver calls
eeh_reset_device() to place the slot into state 1 (Reset) and
eeh_reset_device completes by placing the slot into State 0 (Normal
Operations). Upon return from eeh_reset_device(), the EEH driver calls
eeh_report_reset, which then calls the adapter's slot_reset callback. At
the time the adapter's slot_reset callback is called, the true state of
the hardware is Normal Operations and should be accurately reflected by
setting dev->error_state to pci_channel_io_normal.

The current implementation of EEH driver does not do so and requires
this change to correct this deficiency.
Signed-off-by: NMike Mason <mmlnx@us.ibm.com>
Acked-by: NLinas Vepstas <linasvepstas@gmail.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The EEH code disables and enables interrupts during the
device recovery process.  This is unnecessary for MSI
and MSI-X interrupts because they are effectively disabled
by the DMA Stopped state when an EEH error occurs.  The
current code is also incorrect for MSI-X interrupts.  It
doesn't take into account that MSI-X interrupts are tracked
in a different way than LSI/MSI interrupts.  This patch
ensures only LSI interrupts are disabled/enabled.
Signed-off-by: NMike Mason <mmlnx@us.ibm.com>
Acked-by: NLinas Vepstas <linasvepstas@gmail.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Currently print_device_node_tree() isn't called but it can be useful for
debugging.  Leave the function there but hide it behind '#if 0' to save
it being rewritten.  If you want to call it you're already editing this
file anyway. ;P
Signed-off-by: NTony Breeds <tony@bakeyournoodle.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Fix this:

/usr/src/devel/arch/powerpc/platforms/pseries/eeh_driver.c: In function 'print_device_node_tree':
/usr/src/devel/arch/powerpc/platforms/pseries/eeh_driver.c:55: warning: ISO C90 forbids mixed declarations and code

also make that function look like it's part of Linux.
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Do not wait for the pci slot status before reporting an error
to the device driver. Some systems may take many seconds to
report the slot status, and this can confuse unsuspecting
device drivers.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Bugfix: if a driver controlling one part of a multi-function PCI card
has asked for a reset, honor that request above all others.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Clean up commentary, remove dead code.

Signed-off-by Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Twiddle the copyright notices. Per current guidelines, the use
of the (C) or (c) in source code is deprecated.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>

----
 arch/powerpc/platforms/pseries/eeh.c        |    6 +++++-
 arch/powerpc/platforms/pseries/eeh_cache.c  |    3 ++-
 arch/powerpc/platforms/pseries/eeh_driver.c |    6 +++---
 3 files changed, 10 insertions(+), 5 deletions(-)
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Assorted minor cleanups to EEH code; -- use literals, use
kerneldoc format.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>

----
 arch/powerpc/platforms/pseries/eeh.c        |   13 ++++++++++---
 arch/powerpc/platforms/pseries/eeh_driver.c |    7 ++++---
 include/asm-powerpc/ppc-pci.h               |   18 +++++++++++++++---
 3 files changed, 29 insertions(+), 9 deletions(-)
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Make some minor adjustments to the EEH error messages.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

It turns out many/most versions of firmware enable MMIO when
the slto-error-detail rtas call is made (in violation of the
architecture). Thus, it would be best to call slot-error-detail
only after notifying device drivers of a freeze, as otherwise,
a variety of strange and unexpected things may happen.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Rework how multi-function PCI devices are identified and traversed.
This fixes a bug with multi-function recovery on Power4 that was
introduced by a recent Power4 EEH patch.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

After requesting a state change, verify that the state change
actually ocurred, and the system ends up in the expected state.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The EEH event notification system passes around data that is
not needed or at least, not used properly. Stop passing this
data; get it in a more reliable fashion.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

If the second or higher function of a multi-function device fails
to recover, this failure is not reported upwards. Fix this.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

If a device driver does not have native PCI error recovery,
a hotplug error recovery will be attemped. In this case,
the device driver will not report back whether its healthy
or not; simply assume that it is.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

There are multiple code patchs tht resuls in a "permanent
failure"; when examining rare events, it can be hard to see
which was taken. This patch adds printk's to assist.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Clarify error message re EEH permanent failure.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

If one attempts to create a device driver recovery sequence that
does not depend on a hard reset of the device, but simply just
attempts to resume processing, then one discovers that the
recovery sequence implemented on powerpc is not quite right.
This patch fixes this up.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Update to the PowerPC PCI error recovery code.

Add code to enable MMIO if a device driver reports that it is capable
of recovering on its own.  One anticipated use of this having a device
driver enable MMIO so that it can take a register dump, which might
then be followed by the device driver requesting a full reset.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Clean up subroutine documentation; mostly formatting changes, with
some new content.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Now that get_property() returns a void *, there's no need to cast its
return value. Also, treat the return value as const, so we can
constify get_property later.

pseries platform changes.

Built for pseries_defconfig
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NAdrian Bunk <bunk@stusta.de>

The PCI error recovery code will printk diagnostic info when
a PCI error event occurs. Change the messages to include the slot
location code, which is how most sysadmins will know the device.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

When a PCI device driver does not support PCI error recovery,
the powerpc/pseries code takes a walk through a branch of code
that resets the failure counter. Because of this, if a broken
PCI card is present, the kernel will attempt to reset it an
infinite number of times. (This is annoying but mostly harmless:
each reset takes about 10-20 seconds, and uses almost no CPU time).

This patch preserves the failure count across resets.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The current PCI error recovery system keeps track of the number of PCI card
resets, and refuses to bring a card back up if this number is too large.
The goal of doing this was to avoid an infinite loop of resets if a card is
obviously dead.  However, if the failures are rare, but the machine has a
high uptime, this mechanism might still be triggered; this is too harsh.

This patch will avoids this problem by decrementing the fail count after an
hour.  Thus, as long as a pci card BSOD's less than 6 times an hour, it
will continue to be reset indefinitely.  If it's failure rate is greater
than that, it will be taken off-line permanently.

This patch is larger than it might otherwise be because it changes
indentation by removing a pointless while-loop.  The while loop is not
needed, as the handler is invoked once fo each event (by schedule_work());
the loop is leftover cruft from an earlier implementation.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The recent patch to print device names in EEH reset messages
was lacking ... this patch works better.
Signed-off-by: NLinas Vepstas <linas@linas.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The current code prints an ambiguous message if the recovery
of a failed PCI device fails. Give this special case its own
unique message.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This avoids printk'ing a NULL string.
Signed-off-by: NLinas Vepstas <linas@linas.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch fixes a crash in handle_eeh_events,
but ethtool -t still doesnt work right.

...
pepino:~ # cpu 0x3: Vector: 300 (Data Access) at [c00000005192bbe0]
    pc: c00000000004a380: .handle_eeh_events+0xe0/0x23c
    lr: c00000000004a374: .handle_eeh_events+0xd4/0x23c
    sp: c00000005192be60
   msr: 9000000000009032
   dar: 268
 dsisr: 40000000
  current = 0xc0000001fe7bf1a0
  paca    = 0xc00000000048b280
    pid   = 16322, comm = eehd
enter ? for help
[c00000005192bf00] c00000000004a808 .eeh_event_handler+0xcc/0x130
[c00000005192bf90] c000000000025e00 .kernel_thread+0x4c/0x68

...

(none):/# /usr/sbin/ethtool -i eth0
driver: e100
version: 3.5.10-k2-NAPI
firmware-version: N/A
bus-info: 0000:21:01.0
(none):/# /usr/sbin/ethtool -t eth0
Call Trace:
[C00000000F8DEFF0] [C00000000000F270] .show_stack+0x74/0x1b4 (unreliable)
[C00000000F8DF0A0] [C000000000049D04] .eeh_dn_check_failure+0x290/0x2d8
[C00000000F8DF150] [C000000000049E58] .eeh_check_failure+0x10c/0x138
[C00000000F8DF1E0] [C0000000002DFDB0] .e100_hw_reset+0x70/0xf4
[C00000000F8DF270] [C0000000002E1BBC] .e100_hw_init+0x2c/0x260
[C00000000F8DF310] [C0000000002E2464] .e100_loopback_test+0x8c/0x220
[C00000000F8DF3C0] [C0000000002E28DC] .e100_diag_test+0xdc/0x16c
[C00000000F8DF490] [C000000000420BE0] .dev_ethtool+0xf24/0x14f8
[C00000000F8DF8F0] [C00000000041F4A8] .dev_ioctl+0x5cc/0x740
[C00000000F8DFA20] [C00000000040FEFC] .sock_ioctl+0x3d0/0x404
[C00000000F8DFAC0] [C0000000000D513C] .do_ioctl+0x68/0x108
[C00000000F8DFB50] [C0000000000D56B0] .vfs_ioctl+0x4d4/0x510
[C00000000F8DFC10] [C0000000000D5740] .sys_ioctl+0x54/0x94
[C00000000F8DFCC0] [C0000000000FB6EC] .ethtool_ioctl+0x11c/0x150
[C00000000F8DFD60] [C0000000000F7E40] .compat_sys_ioctl+0x338/0x3bc
[C00000000F8DFE30] [C00000000000871C] syscall_exit+0x0/0x40
EEH: Detected PCI bus error on device 0000:21:01.0
EEH: This PCI device has failed 1 times since last reboot: <NULL> -

modprobe: FATAL: Could not load /lib/modules/2.6.16-rc4-git7/modules.dep: No such file or directory

Cannot get strings: No such device
(none):/#
(none):/# EEH: Unable to configure device bridge (-3) for /pci@400000000110/pci@2,2

(none):/# Call Trace:
[C00000000FA17940] [C00000000000F270] .show_stack+0x74/0x1b4 (unreliable)
[C00000000FA179F0] [C000000000049D04] .eeh_dn_check_failure+0x290/0x2d8
[C00000000FA17AA0] [C00000000001E114] .rtas_read_config+0x120/0x154
[C00000000FA17B40] [C000000000049664] .early_enable_eeh+0x274/0x2bc
[C00000000FA17C00] [C000000000049708] .eeh_add_device_early+0x5c/0x6c
[C00000000FA17C90] [C000000000049748] .eeh_add_device_tree_early+0x30/0x5c
[C00000000FA17D20] [C000000000046568] .pcibios_add_pci_devices+0x8c/0x1f8
[C00000000FA17DD0] [C00000000004A528] .eeh_reset_device+0xe0/0x110
[C00000000FA17E60] [C00000000004A698] .handle_eeh_events+0x140/0x250
[C00000000FA17F00] [C00000000004AC7C] .eeh_event_handler+0xe8/0x140
[C00000000FA17F90] [C000000000025784] .kernel_thread+0x4c/0x68
EEH: Detected PCI bus error on device <NULL>
EEH: This PCI device has failed 1 times since last reboot: <NULL> -
EEH: Unable to configure device bridge (-3) for /pci@400000000110/pci@2,2
Call Trace:
[C00000000FA17940] [C00000000000F270] .show_stack+0x74/0x1b4 (unreliable)
[C00000000FA179F0] [C000000000049D04] .eeh_dn_check_failure+0x290/0x2d8
[C00000000FA17AA0] [C00000000001E114] .rtas_read_config+0x120/0x154
[C00000000FA17B40] [C000000000049664] .early_enable_eeh+0x274/0x2bc
[C00000000FA17C00] [C000000000049708] .eeh_add_device_early+0x5c/0x6c
[C00000000FA17C90] [C000000000049748] .eeh_add_device_tree_early+0x30/0x5c
[C00000000FA17D20] [C000000000046568] .pcibios_add_pci_devices+0x8c/0x1f8
[C00000000FA17DD0] [C00000000004A528] .eeh_reset_device+0xe0/0x110
[C00000000FA17E60] [C00000000004A698] .handle_eeh_events+0x140/0x250
[C00000000FA17F00] [C00000000004AC7C] .eeh_event_handler+0xe8/0x140
[C00000000FA17F90] [C000000000025784] .kernel_thread+0x4c/0x68
EEH: Detected PCI bus error on device <NULL>
EEH: This PCI device has failed 1 times since last reboot: <NULL> -
EEH: Unable to configure device bridge (-3) for /pci@400000000110/pci@2,2
Call Trace:
[C00000000FA17940] [C00000000000F270] .show_stack+0x74/0x1b4 (unreliable)
[C00000000FA179F0] [C000000000049D04] .eeh_dn_check_failure+0x290/0x2d8
[C00000000FA17AA0] [C00000000001E114] .rtas_read_config+0x120/0x154
[C00000000FA17B40] [C000000000049664] .early_enable_eeh+0x274/0x2bc
[C00000000FA17C00] [C000000000049708] .eeh_add_device_early+0x5c/0x6c
[C00000000FA17C90] [C000000000049748] .eeh_add_device_tree_early+0x30/0x5c
[C00000000FA17D20] [C000000000046568] .pcibios_add_pci_devices+0x8c/0x1f8
[C00000000FA17DD0] [C00000000004A528] .eeh_reset_device+0xe0/0x110
[C00000000FA17E60] [C00000000004A698] .handle_eeh_events+0x140/0x250
[C00000000FA17F00] [C00000000004AC7C] .eeh_event_handler+0xe8/0x140
[C00000000FA17F90] [C000000000025784] .kernel_thread+0x4c/0x68
EEH: Detected PCI bus error on device <NULL>
and so on
Signed-off-by: NOlaf Hering <olh@suse.de>
Acked-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

<asm/systemcfg.h> is gone now, and the PCI error recovery constants
in include/linux/pci.h changed their names in the process of getting
accepted.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
(cherry picked from 5a2516156c591fc3d2059fbd93f97e15eb6010d6 commit)

239-eeh-multifunction-consolidate.patch

New-style firmware will often place multiple different functions
under a non-EEH-aware parent.  However, these devices might share
a common PE "partition endpoint" and config address, ad thus any
EEH events will affect all of the devices in common.  This patch
makes the effort to find all of these common devices and handle
them together.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
(cherry picked from 216810296bb97d39da8e176822e9de78d2f00187 commit)

238-eeh-stop-if-reset_failed.patch

If the firmware is unable to reset the PCI slot for some reason, then
don't attempt any further recovery steps after that point.  Instead,
mark the device as permanently failed.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
(cherry picked from e06b942521eb2cdaf232726f45a820d5837acb12 commit)

234-eeh-find-pe.patch

The find_device_pe() routine is duplicated in two files. Remove one of
the two copies, declare the other extern.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
(cherry picked from 48408e708282d4d0269136ff27ea5acbd9410b5a commit)

Various PCI bus errors can be signaled by newer PCI controllers.  The
core error recovery routines are architecture dependent.  This patch adds
a recovery infrastructure for the  PPC64 pSeries systems.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
(cherry picked from e8ca11b460c4c9c7fa6b529be221529ebd770e38 commit)