The mvpp2_phylink_validate() function sets all modes that are
supported by a given PPv2 port. A recent change made all ports to
advertise they support 10G modes in certain cases. This is not true,
as only the port #0 can do so. This patch fixes it.

Fixes: 01b3fd5a ("net: mvpp2: fix detection of 10G SFP modules")
Cc: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Recent changes in the mvneta driver reworked allocation
and handling of the ingress buffers to use entire pages.
Apart from that in SW BM scenario the HW must be informed
via PRXDQS about the biggest possible incoming buffer
that can be propagated by RX descriptors.

The BufferSize field was filled according to the MTU-dependent
pkt_size value. Later change to PAGE_SIZE broke RX operation
when usin 64K pages, as the field is simply too small.

This patch conditionally limits the value passed to the BufferSize
of the PRXDQS register, depending on the PAGE_SIZE used.
On the occasion remove now unused frag_size field of the mvneta_port
structure.

Fixes: 562e2f46 ("net: mvneta: Improve the buffer allocation method for SWBM")
Signed-off-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The .validate phylink callback should empty the supported bitmap when
the interface mode is invalid.

Cc: Maxime Chevallier <maxime.chevallier@bootlin.com>
Cc: Antoine Tenart <antoine.tenart@bootlin.com>
Reported-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mvpp2_phylink_validate() relies on the interface field of
phylink_link_state to determine valid link modes. However, when called
from phylink_sfp_module_insert() this field in not initialized. The
default switch case then excludes 10G link modes. This allows 10G SFP
modules that are detected correctly to be configured at max rate of
2.5G.

Catch the uninitialized PHY mode case, and allow 10G rates.

Fixes: d97c9f4a ("net: mvpp2: 1000baseX support")
Cc: Maxime Chevallier <maxime.chevallier@bootlin.com>
Cc: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using 2.5G speed relies on the SerDes lanes being configured
accordingly. The lanes have to be reconfigured to switch between
1G and 2.5G, and for now only the bootloader does this configuration.

In the case we add a Comphy driver to handle switching the lanes
dynamically, it's better for now to stick with supporting only 1G and
add advertisement for 2.5G once we really are capable of handling both
speeds without problem.

Since the interface mode is initialy taken from the DT, we want to make
sure that adding comphy support won't break boards that don't update
their dtb.

Fixes: da58a931 ("net: mvneta: Add support for 2500Mbps SGMII")
Reported-by: NAndrew Lunn <andrew@lunn.ch>
Reported-by: NRussell King <linux@armlinux.org.uk>
Signed-off-by: NMaxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The reserved variable should be named reserved1.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mvpp2 driver has the curious behaviour of passing a stack variable
to irq_set_affinity_hint(), which results in the kernel exploding
the first time anyone accesses this information. News flash: userspace
does, and irqbalance will happily take the machine down. Great stuff.

An easy fix is to track the mask within the queue_vector structure,
and to make sure it has the same lifetime as the interrupt itself.

Fixes: e531f767 ("net: mvpp2: handle cases where more CPUs are available than s/w threads")
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function nix_update_mce_list() is called from
nix_update_bcast_mce_list(), and a spin lock is held
here, so we should use GFP_ATOMIC instead.

Fixes: 4b05528e ("octeontx2-af: Update bcast list upon NIXLF alloc/free")
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a copy and paste bug where we copied the sizeof() from the chunk
before.  We're copying more data than intended but the destination is a
union so it doesn't cause memory corruption.

Fixes: ffb0abd7 ("octeontx2-af: NIX AQ instruction enqueue support")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By default NIXLF is set in UCAST mode. This patch adds a new
mailbox message which when sent by a RVU PF changes this default
mode. When promiscuous mode is needed, the reserved promisc entry
for each of RVU PF is setup to match against ingress channel number
only, so that all pkts on that channel are accepted and forwarded
to the mode change requesting PF_FUNC's NIXLF.

PROMISC and ALLMULTI modes are supported only for PFs, for VFs only
UCAST mode is supported.
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added a new mailbox message for a PF/VF to set/update
it's NIXLF's MAC address. Also updates unicast NPC
MCAM entry with this address as matching DMAC.
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for a RVU PF/VF to change
NIX Rx flowkey algorithm index in NPC RX RSS_ACTION.
eg: a ethtool command changing RSS algorithm for a netdev
interface would trigger this change in NPC.

If PF/VF doesn't specify any MCAM entry index then default
UCAST entry of the NIXLF attached to PF/VF will be updated
with RSS_ACTION and flowkey index.
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Configure NIX RX flowkey algorithm configuration to support
RSS (receive side scaling). Currently support for only L3/L4
2-tuple and 4-tuple hash of IPv4/v6/TCP/UDP/SCTP is added.
HW supports upto 32 different flowkey algorithms which SW
can define, this patch defines 9. NPC RX ACTION has to point
to one of these flowkey indices for RSS to work.

The configuration is dependent on NPC parse result's layer
info. So if NPC KPU profile changes suchthat LID/LTYPE values
of above said protocols change then this configuration will
most likely be effected.
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Upon NIXLF_ALLOC install a unicast forwarding rule in NPC MCAM
like below
 - Match pkt DMAC with NIXLF attached PF/VF's MAC address.
 - Ingress channel
 - Action is UCAST
 - Forward to PF_FUNC of this NIXLF
And broadcast pkt forwarding rule as
 - Match L2B bit in MCAM search key
 - Ingress channel
 - Action is UCAST, for now, later it will be changed to MCAST.
Only PFs can install this rule

Upon NIXLF_FREE disable all MCAM entries in use by that NIXLF.
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add LMAC channel info like Rx/Tx channel base and count to
NIXLF_ALLOC mailbox message response. This info is used by
NIXLF attached RVU PF/VF to configure SQ's default channel,
TL3_TL2_LINKX_CFG and to install MCAM rules in NPC based
on matching ingress channel number.
Signed-off-by: NStanislaw Kardach <skardach@marvell.com>
Signed-off-by: NTomasz Duszynski <tduszynski@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds some minimal configuration for NPC MCAM and
LDATA extraction which is sufficient enough to install
ucast/bcast/promiscuous forwarding rules. Below is the
config done
- LDATA extraction config to extract DMAC from pkt
  to offset 64bit in MCAM search key.
- Set MCAM lookup keysize to 224bits
- Set MCAM TX miss action to UCAST_DEFAULT
- Set MCAM RX miss action to DROP

Also inorder to have guaranteed space in MCAM to install
ucast forwarding rule for each of RVU PF/VF, reserved
one MCAM entry for each of NIXLF for ucast rule. And two
entries for each of RVU PF. One for bcast pkt replication
and other for promiscuous mode which allows all pkts
received on a HW CGX/LBK channel.
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Config NPC layer info from KPU profile into protocol
checker to identify outer L2/IPv4/TCP/UDP headers in a
packet. And enable IPv4 checksum validation.

L3/L4 and L4 CSUM validation will be enabled by PF/VF
drivers by configuring NIX_AF_LF(0..127)_RX_CFG via mbox
i.e 'nix_lf_alloc_req->rx_cfg'

Also enable setting of NPC_RESULT_S[L2B] when an outer
L2 broadcast address is detected. This will help in
installing NPC MCAM rules for broadcast packets.
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added support for PF/VF drivers to configure NIX to
capture and/or strip VLAN tag from ingress packets.
Signed-off-by: NVamsi Attunuru <vamsi.attunuru@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Upon NIXLF ALLOC/FREE, add or remove corresponding PF_FUNC from
the broadcast packet replication list of the CGX LMAC mapped
RVU PF.
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allocate memory for mcast/bcast/mirror replication entry
contexts, replication buffers (used by HW) and config HW
with corresponding memory bases. Added support for installing
MCEs via NIX AQ mbox.

For now support is restricted to broadcast pkt replication,
hence MCE table size and number of replication buffers
allocated are less. Each CGX LMAC mapped RVU PF is assigned
a MCE table of size 'num VFs of that PF + PF'.
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For each CGX LMAC that is mapped to a RVU PF, allocate
a pkind and config the same in CGX. For a received packet
at CGX LMAC interface this pkind is used by NPC block
to start parsing of packet.
Signed-off-by: NGeetha sowjanya <gakula@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch configures all 16 KPUs and iKPU (pkinds) with
the KPU parser profile defined in npc_profile.h. Each KPU
engine has a 128 entry CAM, only CAM entries which are listed
in the profile are enabled and rest are left disabled.

Also
- Memory is allocated for pkind's bitmap and PFFUNC, interface
  channel mapping.
- Added all CSR offsets of NPC HW block.
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NPC block is responsible for parsing and forwarding
packets to different NIXLFs. NPC has 16 KPU engines
(Kangaroo parse engine) and one iKPU which represents
pkinds. Each physical port either CGX/LBK is assigned
a pkind and upon receiving a packet HW takes that port's
pkind and starts parsing as per the KPU engines config.

This patch adds header files which contain configuration
profile/array for each of the iKPU and 16 KPU engines.
Signed-off-by: NHao Zheng <hao.zheng@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a new mailbox message to reset
a NIXLF's receive and transmit HW stats.
Signed-off-by: NVamsi Attunuru <vamsi.attunuru@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for a PF/VF driver to configure
NIX transmit scheduler queues via mbox. Since PF/VF doesn't
know the absolute HW index of the NIXLF attached to it, AF
traps the register config and overwrites with the correct
NIXLF index.

HW supports shaping, colouring and policing of packets with
these multilevel traffic scheduler queues. Instead of
introducing different mbox message formats for different
configurations and making both AF & PF/VF driver implementation
cumbersome, access to the scheduler queue's CSRs is provided
via mbox. AF checks whether the sender PF/VF has the
corresponding queue allocated or not and dumps the config
to HW. With a single mbox msg 20 registers can be configured.
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added support for a PF/VF to allocate or free NIX transmit
scheduler queues via mbox. For setting up pkt transmission
priorities between queues, the scheduler queues have to be
contiguous w.r.t their HW indices. So both contiguous and
non-contiguous allocations are supported.

Upon receiving NIX_TXSCH_FREE mbox msg all scheduler queues
allocated to sending PFFUNC (PF/VF) will be freed. Selective
free is not supported.
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NNithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/ethernet/marvell/octeontx2/af/rvu.c: In function 'rvu_detach_rsrcs':
drivers/net/ethernet/marvell/octeontx2/af/rvu.c:855:6: warning:
 variable 'devnum' set but not used [-Wunused-but-set-variable]

drivers/net/ethernet/marvell/octeontx2/af/rvu.c:853:7: warning:
 variable 'is_pf' set but not used [-Wunused-but-set-variable]

drivers/net/ethernet/marvell/octeontx2/af/rvu.c: In function 'rvu_mbox_handler_ATTACH_RESOURCES':
drivers/net/ethernet/marvell/octeontx2/af/rvu.c:1054:7: warning:
 variable 'is_pf' set but not used [-Wunused-but-set-variable]

drivers/net/ethernet/marvell/octeontx2/af/rvu.c:1053:6: warning:
 variable 'devnum' set but not used [-Wunused-but-set-variable]

It never used since introduction in commit
746ea742 ("octeontx2-af: Add RVU block LF provisioning support")
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/ethernet/marvell/octeontx2/af/rvu_npa.c: In function 'rvu_npa_init':
drivers/net/ethernet/marvell/octeontx2/af/rvu_npa.c:446:20: warning:
 variable 'block' set but not used [-Wunused-but-set-variable]

It never used since introduction in
commit 7a37245e ("octeontx2-af: NPA block admin queue init")
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for a RVU PF/VF to disable all RQ/SQ/CQ
contexts of a NIX LF via mbox. This will be used by PF/VF drivers
upon teardown or while freeing up HW resources.

A HW context which is not INIT'ed cannot be modified and a
RVU PF/VF driver may or may not INIT all the RQ/SQ/CQ contexts.
So a bitmap is introduced to keep track of enabled NIX RQ/SQ/CQ
contexts, so that only enabled hw contexts are disabled upon LF
teardown.
Signed-off-by: NGeetha sowjanya <gakula@marvell.com>
Signed-off-by: NStanislaw Kardach <skardach@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for a RVU PF/VF to submit instructions to NIX AQ
via mbox. Instructions can be to init/write/read RQ/SQ/CQ/RSS
contexts. In case of read, context will be returned as part of
response to the mbox msg received.
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allocate bitmaps and memory for PFVF mapping info for
maintaining NIX transmit scheduler queues maintenance.
PF/VF drivers will request for alloc, free e.t.c of
Tx schedulers via mailbox.
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Config LSO formats for TSOv4 and TSOv6 offloads.
These formats tell HW which fields in the TCP packet's
headers have to be updated while performing segmentation
offload.

Also report PF/VF drivers the LSO format indices as part
of response to NIX_LF_ALLOC mbox msg. These indices are
used in SQE extension headers while framing SQE for pkt
transmission with TSO offload.
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Upon receiving NIX_LF_ALLOC mbox message allocate memory for
NIXLF's CQ, SQ, RQ, CINT, QINT and RSS HW contexts and configure
respective base iova HW. Enable caching of contexts into NIX NDC.

Return SQ buffer (SQB) size, this PF/VF MAC address etc info
e.t.c to the mbox msg sender.
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Initialize NIX admin queue (AQ) i.e alloc memory for
AQ instructions and for the results. All NIX LFs will submit
instructions to AQ to init/write/read RQ/SQ/CQ/RSS contexts
and in case of read, get context from result memory.

Also before configuring/using NIX block calibrate X2P bus
and check if NIX interfaces like CGX and LBK are in active
and working state.
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for a RVU PF/VF to disable all Aura/Pool
contexts of a NPA LF via mbox. This will be used by PF/VF drivers
upon teardown or while freeing up HW resources.

A HW context which is not INIT'ed cannot be modified and a
RVU PF/VF driver may or may not INIT all the Aura/Pool contexts.
So a bitmap is introduced to keep track of enabled NPA Aura/Pool
contexts, so that only enabled hw contexts are disabled upon LF
teardown.
Signed-off-by: NGeetha sowjanya <gakula@marvell.com>
Signed-off-by: NStanislaw Kardach <skardach@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for a RVU PF/VF to submit instructions to NPA AQ
via mbox. Instructions can be to init/write/read Aura/Pool/Qint
contexts. In case of read, context will be returned as part of
response to the mbox msg received.
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Upon receiving NPA_LF_ALLOC mbox message allocate memory for
NPALF's aura, pool and qint contexts and configure the same
to HW. Enable caching of contexts into NPA NDC.

Return pool related info like stack size, num pointers per
stack page e.t.c to the mbox msg sender.
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Initialize NPA admin queue (AQ) i.e alloc memory for
AQ instructions and for the results. All NPA LFs will submit
instructions to AQ to init/write/read Aura/Pool contexts
and in case of read, get context from result memory.

Added some common APIs for allocating memory for a queue
and get IOVA in return, these APIs will be used by
NIX AQ and for other purposes.
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support to enable or disable internal loopback mode in CGX.
New mbox IDs CGX_INTLBK_ENABLE/DISABLE added for this.
Signed-off-by: NGeetha sowjanya <gakula@marvell.com>
Signed-off-by: NLinu Cherian <lcherian@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Upon receiving notification from firmware the CGX event handler
in the AF driver gets the current link info such as status, speed,
duplex etc from CGX driver and sends it across to PFs who have
registered to receive such notifications.

To support above
 - Mbox messaging support for sending msgs from AF to PF has been added.
 - Added mbox msgs so that PFs can register/unregister for link events.
 - Link notifications are sent to PF under two scenarioss.
  1. When a asynchronous link change notification is received from
     firmware with notification flag turned on for that PF.
  2. Upon notification turn on request, the current link status is
     send to the PF.

Also added a new mailbox msg using which RVU PF/VF can retrieve
their mapped CGX LMAC's current link info. Link info includes
status, speed, duplex and lmac type.
Signed-off-by: NLinu Cherian <lcherian@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>