The MAC Reset was noticed to erase important EEPROM settings.
It is also unnecessary since a chip wide reset was done earlier
in initialization, and that reset preserves EEPROM settings.

There for this patch removes the unnecessary MAC specific reset.
Signed-off-by: NBryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mlx5 driver falsely advertises support of software timestamping.
Fix it by removing the false indication.

Fixes: ef9814de ("net/mlx5e: Add HW timestamping (TS) support")
Signed-off-by: NAlaa Hleihel <alaa@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Expression terminated with "," instead of ";", resulted in
set_fte getting bad value for modify_enable_mask field.

Fixes: bd5251db ("net/mlx5_core: Introduce flow steering destination of type counter")
Signed-off-by: NYuval Avnery <yuvalav@mellanox.com>
Reviewed-by: NDaniel Jurgens <danielj@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

When the completion queue of the RQ is empty, do not immediately return.
If left-over decompressed CQEs (from the previous cycle) were processed,
need to go to the finalization part of the poll function.

Bug exists only when CQE compression is turned ON.

This solves the following issue:
mlx5_core 0000:82:00.1: mlx5_eq_int:544:(pid 0): CQ error on CQN 0xc08, syndrome 0x1
mlx5_core 0000:82:00.1 p4p2: mlx5e_cq_error_event: cqn=0x000c08 event=0x04

Fixes: 4b7dfc99 ("net/mlx5e: Early-return on empty completion queues")
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Reviewed-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

The current code has 2 problems.  It assumes that the RX ring for
the loopback packet is combined with the TX ring.  This is not
true if the ethtool channels are set to non-combined mode.  The
second problem is that it won't work on 57500 chips without
adjusting the logic to get the proper completion ring (cpr) pointer.
Fix both issues by locating the proper cpr pointer through the RX
ring.

Fixes: e44758b7 ("bnxt_en: Use bnxt_cp_ring_info struct pointer as parameter for RX path.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently variable data0 is not being initialized so a garbage value is
being passed to vxge_hw_vpath_fw_api and this value is being written to
the rts_access_steer_data0 register.  There are other occurrances where
data0 is being initialized to zero (e.g. in function
vxge_hw_upgrade_read_version) so I think it makes sense to ensure data0
is initialized likewise to 0.

Detected by CoverityScan, CID#140696 ("Uninitialized scalar variable")

Fixes: 8424e00d ("vxge: serialize access to steering control register")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The LAN7431 uses an external phy, and it can be found anywhere in
the phy address space. This patch uses phy address 1 for LAN7430
only. And searches all addresses otherwise.
Signed-off-by: NBryan Whitehead <Bryan.Whitehead@microchip.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When reading buffer descriptors on RX or on TX completion, an
RX_USED/TX_USED bit is checked first to ensure that the descriptors have
been populated, i.e. the ownership has been transferred. However, there
are no memory barriers to ensure that the data protected by the
RX_USED/TX_USED bit is up-to-date with respect to that bit.

Specifically:

- TX timestamp descriptors may be loaded before ctrl is loaded for the
  TX_USED check, which is racy as the descriptors may be updated between
  the loads, causing old timestamp descriptor data to be used.

- RX ctrl may be loaded before addr is loaded for the RX_USED check,
  which is racy as a new frame may be written between the loads, causing
  old ctrl descriptor data to be used.
  This issue exists for both macb_rx() and gem_rx() variants.

Fix the races by adding DMA read memory barriers on those paths and
reordering the reads in macb_rx().

I have not observed any actual problems in practice caused by these
being missing, though.

Tested on a ZynqMP based system.

Fixes: 89e5785f ("[PATCH] Atmel MACB ethernet driver")
Signed-off-by: NAnssi Hannula <anssi.hannula@bitwise.fi>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bit RX_USED set to 0 in the address field allows the controller to write
data to the receive buffer descriptor.

The driver does not ensure the ctrl field is ready (cleared) when the
controller sees the RX_USED=0 written by the driver. The ctrl field might
only be cleared after the controller has already updated it according to
a newly received frame, causing the frame to be discarded in gem_rx() due
to unexpected ctrl field contents.

A message is logged when the above scenario occurs:

  macb ff0b0000.ethernet eth0: not whole frame pointed by descriptor

Fix the issue by ensuring that when the controller sees RX_USED=0 the
ctrl field is already cleared.

This issue was observed on a ZynqMP based system.

Fixes: 4df95131 ("net/macb: change RX path for GEM")
Signed-off-by: NAnssi Hannula <anssi.hannula@bitwise.fi>
Tested-by: NClaudiu Beznea <claudiu.beznea@microchip.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

64-bit DMA addresses are split in upper and lower halves that are
written in separate fields on GEM. For RX, bit 0 of the address is used
as the ownership bit (RX_USED). When the RX_USED bit is unset the
controller is allowed to write data to the buffer.

The driver does not guarantee that the controller already sees the upper
half when the RX_USED bit is cleared, possibly resulting in the
controller writing an incoming frame to an address with an incorrect
upper half and therefore possibly corrupting unrelated system memory.

Fix that by adding the necessary DMA memory barrier between the writes.

This corruption was observed on a ZynqMP based system.

Fixes: fff8019a ("net: macb: Add 64 bit addressing support for GEM")
Signed-off-by: NAnssi Hannula <anssi.hannula@bitwise.fi>
Acked-by: NHarini Katakam <harini.katakam@xilinx.com>
Tested-by: NClaudiu Beznea <claudiu.beznea@microchip.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On some platforms (currently detected only on SAMA5D4) TX might stuck
even the pachets are still present in DMA memories and TX start was
issued for them. This happens due to race condition between MACB driver
updating next TX buffer descriptor to be used and IP reading the same
descriptor. In such a case, the "TX USED BIT READ" interrupt is asserted.
GEM/MACB user guide specifies that if a "TX USED BIT READ" interrupt
is asserted TX must be restarted. Restart TX if used bit is read and
packets are present in software TX queue. Packets are removed from software
TX queue if TX was successful for them (see macb_tx_interrupt()).
Signed-off-by: NClaudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: NNicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function should return an error if create_singlethread_workqueue()
fails.

Fixes: 34877a15 ("net: stmmac: Rework and fix TX Timeout code")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We accidentally deleted the code to set "rc = -ENOMEM;" and this patch
adds it back.

Fixes: d2201a21 ("qed: No need for LL2 frags indication")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mvpp2_phylink_validate() function sets all modes that are
supported by a given PPv2 port. A recent change made all ports to
advertise they support 10G modes in certain cases. This is not true,
as only the port #0 can do so. This patch fixes it.

Fixes: 01b3fd5a ("net: mvpp2: fix detection of 10G SFP modules")
Cc: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The pointer was NULLed before freeing the memory, resulting in a memory
leak. Trace from kmemleak:

unreferenced object 0xffff88820ae36528 (size 512):
  comm "devlink", pid 5374, jiffies 4295354033 (age 10829.296s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<00000000a43f5195>] kmem_cache_alloc_trace+0x1be/0x330
    [<00000000312f8140>] mlxsw_sp_nve_init+0xcb/0x1ae0
    [<0000000009201d22>] mlxsw_sp_init+0x1382/0x2690
    [<000000007227d877>] mlxsw_sp1_init+0x1b5/0x260
    [<000000004a16feec>] __mlxsw_core_bus_device_register+0x776/0x1360
    [<0000000070ab954c>] mlxsw_devlink_core_bus_device_reload+0x129/0x220
    [<00000000432313d5>] devlink_nl_cmd_reload+0x119/0x1e0
    [<000000003821a06b>] genl_family_rcv_msg+0x813/0x1150
    [<00000000d54d04c0>] genl_rcv_msg+0xd1/0x180
    [<0000000040543d12>] netlink_rcv_skb+0x152/0x3c0
    [<00000000efc4eae8>] genl_rcv+0x2d/0x40
    [<00000000ea645603>] netlink_unicast+0x52f/0x740
    [<00000000641fca1a>] netlink_sendmsg+0x9c7/0xf50
    [<00000000fed4a4b8>] sock_sendmsg+0xbe/0x120
    [<00000000d85795a9>] __sys_sendto+0x397/0x620
    [<00000000c5f84622>] __x64_sys_sendto+0xe6/0x1a0

Fixes: 6e6030bd ("mlxsw: spectrum_nve: Implement common NVE core")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After a packet was decapsulated it is classified to the relevant FID
based on its VNI and undergoes L2 forwarding.

Unlike regular (non-encapsulated) ARP packets, Spectrum does not trap
decapsulated ARP packets during L2 forwarding and instead can only trap
such packets in the underlay router during decapsulation.

Add this missing packet trap, which is required for VXLAN routing when
the MAC of the target host is not known.

Fixes: b02597d5 ("mlxsw: spectrum: Add NVE packet traps")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During the firmware flash process, some of the EMADs get timed out, which
causes the driver to send them again with a limit of 5 retries. There are
some situations in which 5 retries is not enough and the EMAD access fails.
If the failed EMAD was related to the flashing process, the driver fails
the flashing.

The reason for these timeouts during firmware flashing is cache misses in
the CPU running the firmware. In case the CPU needs to fetch instructions
from the flash when a firmware is flashed, it needs to wait for the
flashing to complete. Since flashing takes time, it is possible for pending
EMADs to timeout.

Fix by increasing EMADs' timeout while flashing firmware.

Fixes: ce6ef68f ("mlxsw: spectrum: Implement the ethtool flash_device callback")
Signed-off-by: NShalom Toledo <shalomt@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Recent changes in the mvneta driver reworked allocation
and handling of the ingress buffers to use entire pages.
Apart from that in SW BM scenario the HW must be informed
via PRXDQS about the biggest possible incoming buffer
that can be propagated by RX descriptors.

The BufferSize field was filled according to the MTU-dependent
pkt_size value. Later change to PAGE_SIZE broke RX operation
when usin 64K pages, as the field is simply too small.

This patch conditionally limits the value passed to the BufferSize
of the PRXDQS register, depending on the PAGE_SIZE used.
On the occasion remove now unused frag_size field of the mvneta_port
structure.

Fixes: 562e2f46 ("net: mvneta: Improve the buffer allocation method for SWBM")
Signed-off-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Create a net bridge, add eth and vnet to the bridge. The vnet is used
by a virtual machine. When ping the virtual machine from the outside
host and the virtual machine send multicast at the same time, the ping
package will lost.

The multicast package send to the eth, eth will send it to the bridge too,
and the bridge learn the mac of eth. When outside host ping the virtual
mechine, it will match the promisc entry of the eth which is not expected,
and the bridge send it to eth not to vnet, cause ping lost.

So this patch change promisc tcam entry position to the END of 512 tcam
entries, which indicate lower priority. And separate one promisc entry to
two: mc & uc, to avoid package match the wrong tcam entry.
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In some case, when mac enable|disable and adjust link, may cause hard to
link(or abnormal) between mac and phy. This patch adds the code for rx PCS
to avoid this bug.

Disable the rx PCS when driver disable the gmac, and enable the rx PCS
when driver enable the mac.
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ntuple-filters features is forced on by chip.
But it shows "ntuple-filters: off [fixed]" when use ethtool.
This patch make it correct with "ntuple-filters: on [fixed]".
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There will be a large number of MAC pause frames on the net,
which caused tx timeout of net device. And then the net device
was reset to try to recover it. So that is not useful, and will
cause some other problems.

So need doubled ndev->watchdog_timeo if device watchdog occurred
until watchdog_timeo up to 40s and then try resetting to recover
it.

When collecting dfx information such as hardware registers when tx timeout.
Some registers for count were cleared when read. So need move this task
before update net state which also read the count registers.
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1.In "hns_nic_init_irq", if request irq fail at index i,
  the function return directly without releasing irq resources
  that already requested.

2.In "hns_nic_net_up" after "hns_nic_init_irq",
  if exceptional branch occurs, irqs that already requested
  are not release.
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If there are packets in hardware when changing the speed or duplex,
it may cause hardware hang up.

This patch adds the code to wait rx fbd clean up when ae stopped.
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After resetting dsaf to try to repair chip error such as ecc error,
the net device will be open if net interface is up. But at this time
if there is the users set the net device up with the command ifconfig,
the net device will be opened twice consecutively.

Function napi_enable was called when open device. And Kernel panic will
be occurred if it was called twice consecutively. Such as follow:
static inline void napi_enable(struct napi_struct *n)
{
         BUG_ON(!test_bit(NAPI_STATE_SCHED, &n->state));
         smp_mb__before_clear_bit();
         clear_bit(NAPI_STATE_SCHED, &n->state);
}

[37255.571996] Kernel panic - not syncing: BUG!
[37255.595234] Call trace:
[37255.597694] [<ffff80000008ab48>] dump_backtrace+0x0/0x1a0
[37255.603114] [<ffff80000008ad08>] show_stack+0x20/0x28
[37255.608187] [<ffff8000009c4944>] dump_stack+0x98/0xb8
[37255.613258] [<ffff8000009c149c>] panic+0x10c/0x26c
[37255.618070] [<ffff80000070f134>] hns_nic_net_up+0x30c/0x4e0
[37255.623664] [<ffff80000070f39c>] hns_nic_net_open+0x94/0x12c
[37255.629346] [<ffff80000084be78>] __dev_open+0xf4/0x168
[37255.634504] [<ffff80000084c1ac>] __dev_change_flags+0x98/0x15c
[37255.640359] [<ffff80000084c29c>] dev_change_flags+0x2c/0x68
[37255.769580] [<ffff8000008dc400>] devinet_ioctl+0x650/0x704
[37255.775086] [<ffff8000008ddc38>] inet_ioctl+0x98/0xb4
[37255.780159] [<ffff800000827b7c>] sock_do_ioctl+0x44/0x84
[37255.785490] [<ffff800000828e04>] sock_ioctl+0x248/0x30c
[37255.790737] [<ffff80000026dc6c>] do_vfs_ioctl+0x480/0x618
[37255.796156] [<ffff80000026de94>] SyS_ioctl+0x90/0xa4
[37255.801139] SMP: stopping secondary CPUs
[37255.805079] kbox: catch panic event.
[37255.809586] collected_len = 128928, LOG_BUF_LEN_LOCAL = 131072
[37255.816103] flush cache 0xffff80003f000000  size 0x800000
[37255.822192] flush cache 0xffff80003f000000  size 0x800000
[37255.828289] flush cache 0xffff80003f000000  size 0x800000
[37255.834378] kbox: no notify die func register. no need to notify
[37255.840413] ---[ end Kernel panic - not syncing: BUG!

This patchset fix this bug according to the flag NIC_STATE_DOWN.
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

According to the hip06 datasheet:
1.Six registers use wrong address:
  RCB_COM_SF_CFG_INTMASK_RING
  RCB_COM_SF_CFG_RING_STS
  RCB_COM_SF_CFG_RING
  RCB_COM_SF_CFG_INTMASK_BD
  RCB_COM_SF_CFG_BD_RINT_STS
  DSAF_INODE_VC1_IN_PKT_NUM_0_REG
2.The offset of DSAF_INODE_VC1_IN_PKT_NUM_0_REG should be
  0x103C + 0x80 * all_chn_num
3.The offset to show the value of DSAF_INODE_IN_DATA_STP_DISC_0_REG
  is wrong, so the value of DSAF_INODE_SW_VLAN_TAG_DISC_0_REG will be
  overwrite

These registers are only used in "ethtool -d", so that did not cause ndev
to misfunction.
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are two test cases:
1. Remove the 4 modules:hns_enet_drv/hns_dsaf/hnae/hns_mdio,
   and install them again, must use "ifconfig down/ifconfig up"
   command pair to bring port to work.

   This patch calls phy_stop function when init phy to fix this bug.

2. Remove the 2 modules:hns_enet_drv/hns_dsaf, and install them again,
   all ports can not use anymore, because of the phy devices register
   failed(phy devices already exists).

   Phy devices are registered when hns_dsaf installed, this patch
   removes them when hns_dsaf removed.

The two cases are sometimes related, fixing the second case also requires
fixing the first case, so fix them together.
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

According to the hip06 Datasheet:
1. The offset of INGRESS_SW_VLAN_TAG_DISC should be 0x1A00+4*all_chn_num
2. The offset of INGRESS_IN_DATA_STP_DISC should be 0x1A50+4*all_chn_num
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The get_mac_address() function is normally inline, but when it is
not, we get a warning that this configuration is broken:

WARNING: vmlinux.o(.text+0x4aff00): Section mismatch in reference from the function w90p910_ether_setup() to the function .init.text:get_mac_address()
The function w90p910_ether_setup() references
the function __init get_mac_address().
This is often because w90p910_ether_setup lacks a __init

Remove the __init to make it always do the right thing.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

corrected macro used in tx path. removed redundant hdrlen
and check for !page in chtls_sendmsg
Signed-off-by: NAtul Gupta <atul.gupta@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clang warns:

drivers/net/ethernet/apm/xgene/xgene_enet_main.c:33:36: warning:
tentative array definition assumed to have one element
static const struct acpi_device_id xgene_enet_acpi_match[];
                                   ^
1 warning generated.

Both xgene_enet_acpi_match and xgene_enet_of_match are defined before
their uses at the bottom of the file so this is unnecessary. When
CONFIG_ACPI is disabled, ACPI_PTR becomes NULL so xgene_enet_acpi_match
doesn't need to be defined.
Signed-off-by: NNathan Chancellor <natechancellor@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The value for OEM_CFG_UPDATE command differs between driver and the
Management firmware (mfw). Fix this gap with adding a reserved field.

Fixes: cac6f691 ("qed: Add support for Unified Fabric Port.")
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NAriel Elior <ariel.elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TXQ SQ closure is followed by closing the corresponding CQ. A pending
DIM work would try to modify the now non-existing CQ.
This would trigger an error:
[85535.835926] mlx5_core 0000:af:00.0: mlx5_cmd_check:769:(pid 124399):
MODIFY_CQ(0x403) op_mod(0x0) failed, status bad resource state(0x9), syndrome (0x1d7771)

Fix by making sure to cancel any pending DIM work before destroying the SQ.

Fixes: cbce4f44 ("net/mlx5e: Enable adaptive-TX moderation")
Signed-off-by: NTal Gilboa <talgi@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Remove tx_udp_seg_rem counter from ethtool output, as it is no longer
being updated in the driver's data flow.

Fixes: 3f44899e ("net/mlx5e: Use PARTIAL_GSO for UDP segmentation")
Signed-off-by: NMikhael Goikhman <migo@mellanox.com>
Reviewed-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Currently, we are deleting offloaded encap flows in case the relevant neigh
becomes unconnected while the encap is valid (a sign that it used to be
connected), or if the curr neigh mac is different from the cached mac
(a sign that the remote side changed their mac).

The 2nd check also applies when the neigh becomes connected on the 1st
time (we start with zero mac). Before the offending commit, the deleting
handler was practically no op, as no flows were offloaded. But since
that commit, we offload neigh-less encap flows to slow path.

Under mirroring scheme, we go into the delete handler, attempt to unoffload a
mirror rule which was never set (as we were offloading to slow path) and crash.

Fix that by calling the delete handler only when the encap is valid,
which covers both cases mentioned above.

Fixes: 5dbe906f ('net/mlx5e: Use a slow path rule instead if vxlan neighbour isn't available')
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NEli Britstein <elibr@mellanox.com>
Reviewed-by: NPaul Blakey <paulb@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

When a neighbour is resolved, we delete the goto slow path rule from HW.

The eswitch flow attributes where not properly initialized on that case,
hence we mess up the eswitch refcounts for chain zero (the default one).

Fix that along with making sure to use semicolons and not commas on that code;

Fixes: 5dbe906f ('net/mlx5e: Use a slow path rule instead if vxlan neighbour isn't available')
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: NPaul Blakey <paulb@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Just a leftover which was wrongly left there, remove it while spawning
a message to suggest firmware upgrade.

Fixes: bf07aa73 ('net/mlx5e: Support offloading tc priorities and chains for eswitch flows')
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: NPaul Blakey <paulb@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Currently we are not supporting this and not err-ing on that either.

For now, just err if asked to do that.

Fixes: bf07aa73 ('net/mlx5e: Support offloading tc priorities and chains for eswitch flows')
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Reported-by: NEli Britstein <elibr@mellanox.com>
Reviewed-by: NEli Britstein <elibr@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Add check of MPWQE stride size is within range supported by HW. In case
calculated MPWQE stride size exceed range, linear SKB can't be used and
we should use non linear MPWQE instead.

Fixes: 619a8f2a ("net/mlx5e: Use linear SKB in Striding RQ")
Signed-off-by: NMoshe Shemesh <moshe@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

The default amount of channels a representor opens was erroneously
changed from one to the maximum amount of channels, restore to its
intended value.

Fixes: 779d986d ("net/mlx5e: Do not ignore netdevice TX/RX queues number")
Signed-off-by: NGavi Teitz <gavi@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>