When QCA988X cycle counter HW register wraps
around it resets to 0x7fffffff instead of 0. All
other cycle counter related registers are divided
by 2 so they never wraparound themselves. QCA61X4
has a uniform CC and it wraparounds in a regular
fashion though.

Worst case wraparound time is approx 24 seconds
(2**31 / 88MHz). Since scan channel visit times
are max 5 seconds (offchannel case) it is
guaranteed there's been at most 1 wraparound and
it is possible to compute survey active time
value. It is, however, impossible to determine the
point at which Rx Clear Count has been divided by
two so it is not reported upon wraparound.

This fixes some occasional incorrect survey data
on QCA988X as some channels (depending on how/when
scan/offchannel requests were requested) would
have approx 24 sec active time which wasn't
actually the case.

This should improve hostapd ACS a little bit.
Reported-by: NSrinivasa Duvvuri <sduvvuri@chromium.org>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The macro isn't WMI specific. Instead it is
related to hardware chip so move the macro
accordingly. While at it document the magic value.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Some firmware revisions pad 4th hw address in
Native Wifi Rx decap. This is the case with 10.x
and it was assumed that this is true for all
firmware images.

However QCA988X with 999.999.0.636 and QCA61X4
with WLAN.RM.2.0-00088 don't have the padding.
Hence add a feature flag indicating that the
padding isn't present so firmware images can
advertise it appropriately. This way driver will
behave as it was before with old firmware blobs
and doesn't cause any regressions from user
perspective.

Effectively this patch enables QCA988X with
999.999.0.636 and QCA61X4 with WLAN.RM.2.0-00088
to set up client bridging provided user has an
updated firmware blob.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

By using SOC_WAKE register it is possible to bring
down power consumption of QCA61X4 from 36mA to
16mA when associated and idle.

Currently the sleep threshold/grace period is at a
very conservative value of 60ms.

Contrary to QCA61X4 the QCA988X firmware doesn't
have Rx/beacon filtering available for client mode
and SWBA events are used for beaconing in AP/IBSS
so the SoC needs to be woken up at least every
~100ms in most cases. This means that QCA988X
is at a disadvantage and the power consumption
won't drop as much as for QCA61X4.

Due to putting irq-safe spinlocks on every MMIO
read/write it is expected this can cause a little
performance regression on some systems. I haven't
done any thorough measurements but some of my
tests don't show any extreme degradation.

The patch removes some explicit pci_wake calls
that were added in 320e14b8db51aa ("ath10k: fix
some pci wake/sleep issues"). This is safe because
all MMIO accesses are now wrapped and the device
is woken up automatically if necessary.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

mac80211 can update vif powersave state while
disconnected. Firmware doesn't behave nicely and
consumes more power than necessary if PS is
disabled on a non-started vdev. Hence
force-enable PS for non-running vdevs.

This reduces power drain on QCA61X4 from 88mA to
36mA when interface is up and not associated.
QCA988X wasn't measured.
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It is actually safe to enable ASPM after the
device is booted up.

This reduces power drain of QCA61X4 when driver is
simply loaded (no interface is up) from 31mA to
14mA. QCA988X wasn't measured but doesn't seem to
regress in any other way.
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fix format specifier used for dma_addr_t, namely use %pad
Debug print virtual address for the same buffer as well.

Fixes: dc16427b ("wil6210: Add pmc debug mechanism memory management")
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Rx clear count reported in wmi_chan_info_event is actually channel_busy_count
not rx_frame_count. Send rx_clear_count through time_busy of survey_info
and set SURVEY_INFO_TIME_BUSY in filled.

iw wlan0 survey dump

urvey data from wlan0
        frequency:                      5180 MHz [in use]
        noise:                          -103 dBm
        channel active time:            150 ms
        channel busy time:              22 ms
Survey data from wlan0
        frequency:                      5200 MHz
        noise:                          -102 dBm
        channel active time:            146 ms
        channel busy time:              0 ms
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Spectral scan supported by ath10k has capability to monitor and report
through whole bands and channels, but current buffer size is too small
to save reported spectral scan data.
This results in dropping 5G channel reports at all when dual band card
is used, so that users are not able to analyze spectral environments.
Hence increase the buffer size to fix the problem.

A spectral data size is vary based on the number of bins, so the unit
buffer size, 1140, is chose to minimize relay buffer fragmentation.

The total buffer size is also chose in tradeoff with spectral scan
support vs. kernel memory consumption.
Since theoretical maximum buffer size, 9.5MB, can be consumed with
512 bins in dual bands, we target to cover up to 128 bins for all
channels in dual bands and due to the buffer size limitation,
spectral scan with bin number bigger than 128 needs to be run on
single band each.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This prevents silence failures with driver waiting (infinitely) for a
callback.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

"flowrings" and "*flowrings" are both pointers so this always returns
sizeof(void *) and the current code works fine.  But "*flowrings" is
intended here and static checkers complain, so lets change it.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

If the wl18xx-conf.bin file is missing or invalid (e.g. due
to recent driver change), fallback to default configuration
instead of failing driver load.
Reported-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

cfg80211 would complain about invalid AID in during TDLS setup.
This was happening because we use same AID value as provide by AP
while forming setup messages.
Parse AID from Association response and filter BIT14 and BIT15
of AID to get valid AID.
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

wait_event_interruptible_timeout() returns 0 upon timeout. We should
convert it to a negative error code (such as -ETIMEDOUT) instead of
returning it directly, as return code of 0 indicates that command was
executed.
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Normal FFT reports generate a LOT of data, to save resources
enable short repeat by default also on ath9k_htc (it's already
enabled by default on ath9k). This can always be changed from
userspace if needed.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

E/M noise is a pretty good source of entropy so we mix the FFT
measurements of the E/M spectrum to /dev/random pool. Note that
this doesn't increase the pool's entropy count but it still helps
on improving the output of /dev/(u)random.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Temp buffer is only used for fixing malformed frames, there is no
need to memset it every time.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

There is no reason to keep processing FFT reports if there is no
space left on the relayfs buffers for the results. This saves
lots of CPU cycles, especially on normal (non-short) reports.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

No need to copy the frame to the temporary buffer when its length
is ok.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Since we have lots of frames on a normal FFT report don't bother
processing the malformed ones. Only try to fix malformed frames
in case of a short FFT report (only a single frame on the report).
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Since we can identify the FFT frames on the report by checking the
consistency of their magnitude info, we can process all of them,
even when some of them are corrupted.

This patch introduces two functions to quickly verify the integrity
of the mag_info fields and some further tweaks to detect the frames
in the report and process them.

Note that in case of missing bytes we don't duplicate them, instead
we leave them as zeroes. This way we get less noise on the FFT plot.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

a) Check that the maximum magnitude is at the specified index

b) Check if the maximum magnitude index is at dc_pos and if so
calculate a new one (value at dc_pos is invalid)

c) Check if the specified maximum magnitude is indeed the maximum
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Since more checks and fixes will be added later and ath_cmn_process_fft is
already big enough.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Maximum magnitude index is a 5bit signed integer,
convert to an 8bit signed integer and then "shift" it so that it can be used
as an array index. Note that the current implementation adds +1 to the index
value (so it can't be used as an array index) and it's only valid for HT20
channels.

Note that the maximum magnitude index is not being used by
the userspace tools that parse FFT samples (they just use
maximum magnitude) so this doesn't break userspace compatibility.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

FFT spectral scan is a functionality that makes sense to have its own
debug flag.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

* Interrupt request need to happen when the wilink chip is powered on and
  driving the wlan_irq line. This avoids spurious interrupt issues that
  are a result of different external pulls configuration on different
  platforms
* Allow working with wl18xx level-low and falling edge irqs by configuring
  wl18xx to invert the device interrupt
Signed-off-by: NEyal Reizer <eyalr@ti.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch fix some spelling typo in drivers/net/wirless
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

We will reset more_task_flag at the end of main process
routine. This optimization will help to remove spinlock
operations at couple of places in the code.
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

With PCIE it is possible to support multiple devices with the
same device type. They all load the same nvram file. In order to
support this the nvram can specify which part of the nvram is
for which pcie device. This patch adds support for these new
types of nvram files.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds support for the BCM4358 2x2 11ac device.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

commit 330b4e4b ("brcmfmac: Add wowl support for SDIO devices.")
changed the behaviour by removing the MMC_PM_KEEP_POWER flag for
non-wowl scenario, which needs to be restored. Another necessary
change is to mark the card as being non-removable. With this in place
the suspend resume test passes successfully doing:

 # echo devices > /sys/power/pm_test
 # echo mem > /sys/power/state

Note that power may still be switched off when system is going
in S3 state.
Reported-by: NFu, Zhonghui <&lt;zhonghui.fu@linux.intel.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Acked-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When the sdio bus state is not ready to process we abort the
interrupt service routine. This is not wanted as it keeps the
interrupt source active. Better clear the interrupt source.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds support for the BCM4324 B5 revision. This device
is similar to BCM43241 from driver and firmware perspective. It
is known to be used in Lenovo Thinkpad Tablet devices.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The scheduled scan support depends on firmware supporting the PNO
feature. This feature is optional so add a feature flag for this
in the driver and announce scheduled scan support accordingly.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Some feature flags were not described in the header file. Adding
the description.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When change the country code the available channels may change. So
the wiphy bands should be updated accordingly.
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The driver was constructing a list of channels per wiphy band
by querying the device. This list is not what the hardware is
able to do as it is already filtered by the country setting in
the device. As user-space may change the country this would
require updating the channel list which is not recommended [1].
This patch introduces a superset of channels. The individual
channels are disabled appropriately by querying the device.

[1] http://mid.gmane.org/1426706320.3001.21.camel@sipsolutions.netReviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch fixes an issue where it was discovered that driver is setting
invalid HT IEs to FW. This was happening because bug in parsing HT IE.
Driver would incorrectly point to start of HT IE while FW only needs actual
HT configuration - excluding EID and length.
Signed-off-by: NZhaoyang Liu <liuzy@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch reverts 'commit c5534844 ("mwifiex:
enable aggregation for TID 6 and 7 streams")'.
TID6 & TID7 is voice traffic which is quite time sensitive.
Do not enable any type of aggregation on these TIDs.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>