Channel disabling/halting should performed for enabled only channels
to avoid warnings "Unable to clear enable on channel N" which seen
if host works in Slave mode.
Signed-off-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

On ISOC transfer completion, in DDMA mode, set actual frame
number returning to function driver in usb_request.

Due to core limitation, returning frame number is 11-bit wide.
Signed-off-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Some function drivers queueing more than 128 ISOC requests at a time.
To avoid "descriptor chain full" cases, increasing descriptors count
from MAX_DMA_DESC_NUM_GENERIC to MAX_DMA_DESC_NUM_HS_ISOC for ISOC's
only.
Signed-off-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Added delayed status support for Control transfers.

Tested in all 3 modes: Slave, BDMA and DDMA.
Performed tests: USB CV (Ch9 and MSC), Control Read/Write tests
using Synopsys USB test environment function driver.
Signed-off-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Most of the phy initialization is shared between host and gadget,
this adds the turnaround configuration only used by gadgets to
the global phy init.
Acked-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NJules Maselbas <jmaselbas@kalray.eu>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

As the phy initialization is almost the same in host and gadget
mode. This only move the phy initialization functions into core.c
for now, the goal is to share theses functions between the two modes.
Acked-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NJules Maselbas <jmaselbas@kalray.eu>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

The phy utmi width information is already set in hsotg params,
phyif is only used in few places and I don't see any reason to
not use hsotg's params.

Moreover the utmi width was being forced to 16 bits by platform
initialization which doesn't take in account HW configuration.
Acked-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NJules Maselbas <jmaselbas@kalray.eu>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

The function dwc2_hsotg_init is only called once just before calling
dwc2_hsotg_core_init_disconnected which does the same initialization:
setting the usbcfg register with turnaround time, timeout calibration
and phy width.
Acked-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NJules Maselbas <jmaselbas@kalray.eu>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Makes GHWCFG4_UTMI_PHY_DATA* defines closer to their relative shift and
mask defines to improve readability.
Acked-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NJules Maselbas <jmaselbas@kalray.eu>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

On the rk3288 USB host-only port (the one that's not the OTG-enabled
port) the PHY can get into a bad state when a wakeup is asserted (not
just a wakeup from full system suspend but also a wakeup from
autosuspend).

We can get the PHY out of its bad state by asserting its "port reset",
but unfortunately that seems to assert a reset onto the USB bus so it
could confuse things if we don't actually deenumerate / reenumerate the
device.

We can also get the PHY out of its bad state by fully resetting it using
the reset from the CRU (clock reset unit), which does a more full
reset.  The CRU-based reset appears to actually cause devices on the bus
to be removed and reinserted, which fixes the problem (albeit in a hacky
way).

It's unfortunate that we need to do a full re-enumeration of devices at
wakeup time, but this is better than alternative of letting the bus get
wedged.
Signed-off-by: NDouglas Anderson <dianders@chromium.org>
Signed-off-by: NYunzhi Li <lyz@rock-chips.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

When the driver tries to get optional clock, it ignores all errors,
but if only ignores -ENOENT, it will cover some real errors, such as
-EPROBE_DEFER, so use devm_clk_get_optional() to get optional clock.

Cc: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NChunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Avoiding switch to L1 state in any stage of control transfers.
Send NYET handshake to LPM token.

Renamed GLPMCFG_LPM_ACCEPT_CTRL_ISOC to GLPMCFG_LPM_REJECT_CTRL_CONTROL
because by setting this bit core reject LPM token.
Signed-off-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

This is an attempt to rehash commit 0cf884e8 ("usb: dwc2: add bus
suspend/resume for dwc2") on ToT.  That commit was reverted in commit
b0bb9bb6 ("Revert "usb: dwc2: add bus suspend/resume for dwc2"")
because apparently it broke the Altera SOCFPGA.

With all the changes that have happened to dwc2 in the meantime, it's
possible that the Altera SOCFPGA will just magically work with this
change now.  ...and it would be good to get bus suspend/resume
implemented.

This change is a forward port of one that's been living in the Chrome
OS 3.14 kernel tree.
Signed-off-by: NDouglas Anderson <dianders@chromium.org>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

This patchs sets the params for the DWC2 Controller found in the
Amlogic G12A SoC family.

It mainly sets the settings reported incorrect by the driver,
leaving the remaining detected automatically by the driver and
provided by the DT node.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Acked-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    struct boo entry[];
};

size = sizeof(struct foo) + count * sizeof(struct boo);
instance = kzalloc(size, GFP_KERNEL);

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);

Notice that, in this case, variable size is not necessary, hence
it is removed.

This code was detected with the help of Coccinelle.
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds support for transferring requests, which are
non-contiguous in physical memory, i.e. the data buffer is described by
a scatter-list. This allows transferring large requests without relying
on error-prone contiguous buffer allocations. This way of allocating
requests is already implemented in functionfs and TCM USB functions and
automatically used if UDC driver advertises scatter-gather suppport.
Signed-off-by: NAndrzej Pietrasiewicz <andrzej.p@samsung.com>
[mszyprow: fixed null pointer issue, rewrote commit message]
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

In case when some EP IN is frequently reused, i.e. enabled/disabled by
function driver. It is required to clear TxFIFO number field in DIEPCTL
register before setting new number. Otherwise there is probability to
have same TxFIFO number for different EP's because of OR operator.
Signed-off-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

There are a few remaining drivers/usb/ files that do not have SPDX
identifiers in them, all of these are either Kconfig or Makefiles.  Add
the correct GPL-2.0 identifier to them to make scanning tools happy.
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

To clear GINTSTS2_WKUP_ALERT_INT bit in GINTSTS2 register
require to write 1. This bit is implemented as "Write to clear".

Fixes: 187c5298 ("usb: dwc2: gadget: Add handler for WkupAlert interrupt")
Signed-off-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Disabling all EP's allow to reset EP's to initial state.
Introduced new function dwc2_hsotg_ep_disable_lock() which
before calling dwc2_hsotg_ep_disable() function acquire
hsotg->lock and release on exiting.
From dwc2_hsotg_ep_disable() function removed acquiring
hsotg->lock.
In dwc2_hsotg_core_init_disconnected() function when USB
reset interrupt asserted disabling all ep’s by
dwc2_hsotg_ep_disable() function.
This updates eliminating sparse imbalance warnings.

Reverted changes in dwc2_hostg_disconnect() function.
Introduced new function dwc2_hsotg_ep_disable_lock().
Changed dwc2_hsotg_ep_ops. Now disable point to
dwc2_hsotg_ep_disable_lock() function.
In functions dwc2_hsotg_udc_stop() and dwc2_hsotg_suspend()
dwc2_hsotg_ep_disable() function replaced by
dwc2_hsotg_ep_disable_lock() function.
In dwc2_hsotg_ep_disable() function removed acquiring
of hsotg->lock.

Fixes: dccf1bad ("usb: dwc2: Disable all EP's on disconnect")
Signed-off-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Disable power_down by setting the parameter to
DWC2_POWER_DOWN_PARAM_NONE. This fixes a problem on various Amlogic
Meson SoCs where USB devices are only recognized when plugged in before
booting Linux. A hot-plugged USB device was not detected even though the
device got power (my USB thumb drive for example has an LED which lit
up).

A similar fix was implemented for Rockchip SoCs in commit c216765d
("usb: dwc2: disable power_down on rockchip devices"). That commit
suggests that a change in the dwc2 driver is the cause because the
default value for the "hibernate" parameter (which then got renamed to
"power_down" to support other modes) was changed in the v4.17 merge
window with:
commit 6d23ee9c ("Merge tag 'usb-for-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-testing").

Cc: <stable@vger.kernel.org> # 4.19
Acked-by: NMinas Harutyunyan <hminas@synopsys.com>
Suggested-by: NChristian Hewitt <christianshewitt@gmail.com>
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Modify the wait delay utilize the high resolution timer API to allow for
more precisely scheduled callbacks.

A previous commit added a 1ms retry delay after multiple consecutive
NAKed transactions using jiffies. On systems with a low timer interrupt
frequency, this delay may be significantly longer than specified,
resulting in misbehavior with some USB devices.

This scenario was reached on a Raspberry Pi 3B with a Macally FDD-USB
floppy drive (identified as 0424:0fdc Standard Microsystems Corp.
Floppy, based on the USB97CFDC USB FDC). With the relay delay, the drive
would be unable to mount a disk, replying with NAKs until the device was
reset.

Using ktime, the delta between starting the timer (in dwc2_hcd_qh_add)
and the callback function can be determined. With the original delay
implementation, this value was consistently approximately 12ms. (output
in us).

    <idle>-0     [000] ..s.  1600.559974: dwc2_wait_timer_fn: wait_timer delta: 11976
    <idle>-0     [000] ..s.  1600.571974: dwc2_wait_timer_fn: wait_timer delta: 11977
    <idle>-0     [000] ..s.  1600.583974: dwc2_wait_timer_fn: wait_timer delta: 11976
    <idle>-0     [000] ..s.  1600.595974: dwc2_wait_timer_fn: wait_timer delta: 11977

After converting the relay delay to using a higher resolution timer, the
delay was much closer to 1ms.

    <idle>-0     [000] d.h.  1956.553017: dwc2_wait_timer_fn: wait_timer delta: 1002
    <idle>-0     [000] d.h.  1956.554114: dwc2_wait_timer_fn: wait_timer delta: 1002
    <idle>-0     [000] d.h.  1957.542660: dwc2_wait_timer_fn: wait_timer delta: 1004
    <idle>-0     [000] d.h.  1957.543701: dwc2_wait_timer_fn: wait_timer delta: 1002

The floppy drive operates properly with delays up to approximately 5ms,
and sends NAKs for any delays that are longer.

Fixes: 38d2b5fb ("usb: dwc2: host: Don't retry NAKed transactions right away")
Cc: <stable@vger.kernel.org>
Reviewed-by: NDouglas Anderson <dianders@chromium.org>
Acked-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NTerin Stock <terin@terinstock.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Power down feature of DWC2 module integrated in Samsung SoCs doesn't work
properly or needs some additional handling in PHY or SoC glue layer, so
disable it for now. Without disabling power down, DWC2 causes random memory
trashes and fails enumeration if there is no USB link to host on driver
probe.

Fixes: 03ea6d6e ("usb: dwc2: Enable power down")
Acked-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Set GLPMCFG_LPM_ACCEPT_CTRL_ISOC bit in GLPMCFG register
to accept LPM token during ISOC transfers when TxFIFO is
not empty.

- Added two definitions.
  	#define GLPMCFG_LPM_ACCEPT_CTRL_CONTROL        BIT(21)
  	#define GLPMCFG_LPM_ACCEPT_CTRL_ISOC   BIT(22)
  This patch uses GLPMCFG_LPM_ACCEPT_CTRL_ISOC.
  GLPMCFG_LPM_ACCEPT_CTRL_CONTROL is defined for further use.

- Added setting GLPMCFG_LPM_ACCEPT_CTRL_ISOC bit in GLPMCFG
  register in dwc2_gadget_init_lpm function.
Signed-off-by: NArtur Petrosyan <arturp@synopsys.com>
Signed-off-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

According to the databook DCTL_RMTWKUPSIG bit
is defined in DCTL register not in DCFG.

Updated setting DCTL_RMTWKUPSIG bit to DCTL
register.

Fixes: 187c5298 ("usb: dwc2: gadget: Add handler for WkupAlert interrupt")
Signed-off-by: NArtur Petrosyan <arturp@synopsys.com>
Signed-off-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

We added some error handling to this function but forgot to set the
error code on this path.

Fixes: ecd29dab ("usb: dwc2: pci: Handle error cleanup in probe")
Acked-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

 The bug would let the usb controller enter partial power down,
 which was formally known as hibernate, upon boot if nothing was plugged
 in to the port. Partial power down couldn't be exited properly, so any
 usb devices plugged in after boot would not be usable.

 Before the name change, params.hibernation was false by default, so
 _dwc2_hcd_suspend() would skip entering hibernation. With the
 rename, _dwc2_hcd_suspend() was changed to use  params.power_down
 to decide whether or not to enter partial power down.

 Since params.power_down is non-zero by default, it needs to be set
 to 0 for rockchip devices to restore functionality.

 This bug was reported in the linux-usb thread:
 REGRESSION: usb: dwc2: USB device not seen after boot

 The commit that caused this regression is:
6d23ee9cSigned-off-by: NSolidHal <hal@halemmerich.com>
Acked-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Added interrupt handler for WkupAlert interrupt.

This interrupt should initiate Remote Wake up.
Acked-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NGrigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

WKUP_ALERT interrupt should be unmask when lpm mode is enabled.

This interrupt is asserted when the device is in L1 for the duration
mentioned in GREFCLK.SOF_CNN_WKUP_ALERT. This is used to alert SW to
initiate Remote wake up so that the device resumes in time in order not
to lose sync with the host frame number.
Acked-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NGrigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Added dwc2_gadget_program_ref_clk function to program GREFCLK
register in device mode.
Acked-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NGrigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Added ref_clk_per and sof_cnt_wkup_alert parameters in
dwc2_core_params struct and set default values.
Acked-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NGrigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

New registers were added to dwc otg core.

GREFCLK - This register used to control ref_clk parameters.

GINTSTS2 - New WKUP_ALERT interrupt was added.

GINTMSK2 - Mask register for GINTSTS2.
Acked-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NGrigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

In service interval based scheduling target (u)frame must be
set as a last frame in this the service interval.
Acked-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NGrigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Added dwc2_gadget_dec_frame_num_by_one() function in gadget.c.
This function will be used to calculate descriptor frame number field
value. For service interval mode frame number in descriptor should point
to last (u)frame in the interval.
Acked-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NGrigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Added core parameter for service interval based scheduling.
Acked-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NGrigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Added GHWCFG4_SERVICE_INTERVAL_SUPPORTED and
DCTL_SERVICE_INTERVAL_SUPPORTED bits definitions to support
service interval based scheduling.
Acked-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NGrigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

When using external vbus supply regulator, it should be enabled
synchronously with PWR bit in HPRT register. This also fixes
unbalanced use of this optional regulator (This can be reproduced
easily when unbinding the driver).

Fixes: 531ef5eb ("usb: dwc2: add support for host mode external
vbus supply")
Tested-by: NArtur Petrosyan <arturp@synopsys.com>
Acked-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NFabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: NAmelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

dwc2_vbus_supply_exit() may call regulator_disable(). It shouldn't be
called with interrupts disabled as it might sleep.
This is seen with DEBUG_ATOMIC_SLEEP=y.

Fixes: 531ef5eb ("usb: dwc2: add support for host mode external
vbus supply")
Tested-by: NArtur Petrosyan <arturp@synopsys.com>
Acked-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NFabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: NAmelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

There's a race with root hub resume, when using external vbus supply.
Root hub gets resumed, but runtime pm autosuspend runs as external vbus
supply isn't enabled. So, host never exit from power down properly.
Initialize vbus external supply before, rater that after hub resume.

Fixes: 531ef5eb ("usb: dwc2: add support for host mode external
vbus supply")
Tested-by: NArtur Petrosyan <arturp@synopsys.com>
Acked-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NFabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: NAmelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Move devm_regulator_get_optional() call to probe routine. This avoids
'vbus-supply' regulator to be requested lots of times, upon each call
to dwc2_vbus_supply_init(), e.g. like with runtime pm.

Fixes: 531ef5eb ("usb: dwc2: add support for host mode external
vbus supply")
Tested-by: NArtur Petrosyan <arturp@synopsys.com>
Acked-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NFabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: NAmelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>