usb: dwc2: gadget: Replace phyif with phy_utmi_width

The phy utmi width information is already set in hsotg params,
phyif is only used in few places and I don't see any reason to
not use hsotg's params.

Moreover the utmi width was being forced to 16 bits by platform
initialization which doesn't take in account HW configuration.
Acked-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NJules Maselbas <jmaselbas@kalray.eu>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

drivers/usb/dwc2/core.h

@@ -871,7 +871,6 @@ struct dwc2_hregs_backup {
  *                      removed once all SoCs support usb transceiver.
  * @supplies:           Definition of USB power supplies
  * @vbus_supply:        Regulator supplying vbus.
- * @phyif:              PHY interface width
  * @lock:		Spinlock that protects all the driver data structures
  * @priv:		Stores a pointer to the struct usb_hcd
  * @queuing_high_bandwidth: True if multiple packets of a high-bandwidth
@@ -1056,7 +1055,6 @@ struct dwc2_hsotg {
 	struct dwc2_hsotg_plat *plat;
 	struct regulator_bulk_data supplies[DWC2_NUM_SUPPLIES];
 	struct regulator *vbus_supply;
-	u32 phyif;
 
 	spinlock_t lock;
 	void *priv;

drivers/usb/dwc2/gadget.c

@@ -3314,20 +3314,28 @@ void dwc2_hsotg_core_init_disconnected(struct dwc2_hsotg *hsotg,
 
 	/* keep other bits untouched (so e.g. forced modes are not lost) */
 	usbcfg = dwc2_readl(hsotg, GUSBCFG);
+	/* remove the HNP/SRP */
 	usbcfg &= ~(GUSBCFG_TOUTCAL_MASK | GUSBCFG_PHYIF16 | GUSBCFG_SRPCAP |
-		GUSBCFG_HNPCAP | GUSBCFG_USBTRDTIM_MASK);
+		GUSBCFG_HNPCAP);
+	usbcfg |= GUSBCFG_TOUTCAL(7);
 
 	if (hsotg->params.phy_type == DWC2_PHY_TYPE_PARAM_FS &&
 	    (hsotg->params.speed == DWC2_SPEED_PARAM_FULL ||
 	     hsotg->params.speed == DWC2_SPEED_PARAM_LOW)) {
 		/* FS/LS Dedicated Transceiver Interface */
 		usbcfg |= GUSBCFG_PHYSEL;
-	} else {
-		/* set the PLL on, remove the HNP/SRP and set the PHY */
-		val = (hsotg->phyif == GUSBCFG_PHYIF8) ? 9 : 5;
-		usbcfg |= hsotg->phyif | GUSBCFG_TOUTCAL(7) |
-			(val << GUSBCFG_USBTRDTIM_SHIFT);
+	} else if (hsotg->params.phy_type == DWC2_PHY_TYPE_PARAM_UTMI) {
+		if (hsotg->params.phy_utmi_width == 16)
+			usbcfg |= GUSBCFG_PHYIF16;
+
+		/* Set turnaround time */
+		usbcfg &= ~GUSBCFG_USBTRDTIM_MASK;
+		if (hsotg->params.phy_utmi_width == 16)
+			usbcfg |= 5 << GUSBCFG_USBTRDTIM_SHIFT;
+		else
+			usbcfg |= 9 << GUSBCFG_USBTRDTIM_SHIFT;
 	}
+
 	dwc2_writel(hsotg, usbcfg, GUSBCFG);
 
 	dwc2_hsotg_init_fifo(hsotg);

drivers/usb/dwc2/platform.c

@@ -230,9 +230,6 @@ static int dwc2_lowlevel_hw_init(struct dwc2_hsotg *hsotg)
 
 	reset_control_deassert(hsotg->reset_ecc);
 
-	/* Set default UTMI width */
-	hsotg->phyif = GUSBCFG_PHYIF16;
-
 	/*
 	 * Attempt to find a generic PHY, then look for an old style
 	 * USB PHY and then fall back to pdata
@@ -280,7 +277,7 @@ static int dwc2_lowlevel_hw_init(struct dwc2_hsotg *hsotg)
 		 * width is 8-bit and set the phyif appropriately.
 		 */
 		if (phy_get_bus_width(hsotg->phy) == 8)
-			hsotg->phyif = GUSBCFG_PHYIF8;
+			hsotg->params.phy_utmi_width = 8;
 	}
 
 	/* Clock */