Make sky2 handle carrier similar to other drivers,
eliminate some possible races in carrier state transistions.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch restores a couple of workarounds from 2.6.16:
 * restart transmit moderation timer in case it expires during IRQ routine
 * default to having 10 HZ watchdog timer.
At this point it more important not to hang than to worry about the
power cost.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

New version because of new chip support.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Enable support for Yukon EX chipset (88e8071).
Most of changes are related to new commands to chip for transmit,
and change in status and checksumming.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The General Purpose I/O register is yet another hardware workaround
catchall. Enable workaround that vendor driver does to stay
but for bug compatiable.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Catch-22: On Yukon EX (88E8071) need to have internal clocks enabled
before reading chip id. It is harmless on other chips.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This register is more of a test and control register on Yukon2.
So rename it to Q_TEST and give some bit definitions.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Need to setup more PCI control control registers are on Yukon EX.
Some of these also exist on Yukon EC-U as well.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

On Yukon EX reading some of the undocumented places in the
memory space will cause a hang. Since they don't provide useful
information, just skip the reserved areas.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fix sky2 disabling VLAN completely when the first vid is unregistered.

sky2 disables VLAN completely when the first VID is unregistered. It
should instead disable VLAN when the group is unregistered by calling
sky2_vlan_rx_register with grp = NULL.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>

 drivers/net/sky2.c |   25 +++++++++++++------------
 1 file changed, 13 insertions(+), 12 deletions(-)
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Driver was reading value from one register, setting bit and then
writing the wrong register.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Driver was not correctly setting up transmit descriptor when doing
VLAN tag insertion with checksum offload.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This code inherited from the sk98lin driver is incorrect on the Yukon2.
The GPHY_CTRL register values are specific to the internal PHY of the chip
and the values used were leftovers.
Driver was setting bit 13 which is now the INT polarity for the PHY!
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Do some memory barrier changes for safety/perfomance:
Don't need read after update to index, mmiowb() followed by read at end
of irq is sufficient.
Signed-off-by: NStephn Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This workaround was added to deal with NAPI core and how
it affected dual port shared polling. It turned out not to
be necessary. Stopping device 0 only doesn't stop NAPI from
working completely after that.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Make sure that if we ever get a MIB counter overflow interrupt (normally
masked off), that the IRQ is cleared.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

When driver can't allocate receive buffer it drops incoming
packet. Keep a counter.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Align the PHY setup of the sky2 driver with the vendor sk98lin (10.0.4.3)
driver. The PHY register settings are mostly black magic, even with access
to the documentation it isn't clear what the right values are. The changes
are mostly comments, the code change only affects the Yukon FE (100 mbit only)
version.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The problems with Gigabyte motherboards are system configuration dependent.
Since it works fine for some users, it doesn't make sense to deprive
them.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Use DMI to add a blacklist of broken boards (so far only one).
Hopefully, the problems will be solved later, and the the whole
blacklist can disappear.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The driver is not ready to support 88e8071 chip.
If this chip is present, system will hang on boot.

So remove it from PCI device id's for now.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

If the device is fails during module startup for some reason like
unsupported chip version then the driver would crash dereferencing a
null pointer, on shutdown or suspend/resume.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This fixes the regression in 2.6.21 for users with 88e8056 on motherboard.
Allow all but the Gigabyte motherboard has some unresolved bus problems.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

To clearly state the intent of copying from linear sk_buffs, _offset being a
overly long variant but interesting for the sake of saving some bytes.
Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>

The ip_hdrlen() buddy, created to reduce the number of skb->h.th-> uses and to
avoid the longer, open coded equivalent.

Ditched a no-op in bnx2 in the process.

I wonder if we should have a BUG_ON(skb->h.th->doff < 5) in tcp_optlen()...
Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For the quite common 'skb->h.raw - skb->data' sequence.
Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For the common sequence "skb->nh.iph->ihl * 4", removing a good number of open
coded skb->nh.iph uses, now to go after the rest...

Just out of curiosity, here are the idioms found to get the same result:

skb->nh.iph->ihl << 2
skb->nh.iph->ihl<<2
skb->nh.iph->ihl * 4
skb->nh.iph->ihl*4
(skb->nh.iph)->ihl * sizeof(u32)
Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The Yukon FE (100mbit only) chips do not support large packets.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The Yukon EC Ultra chips have transmit settings for store and
forward and PCI buffering. By setting these appropriately, normal
performance goes from 750Mbytes/sec to 940Mbytes/sec (non-jumbo).

It is also possible to do Jumbo mode, but it means turning off
TSO and checksum offload so the performance gets worse. There isn't
enough buffering for checksum offload to work.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Need to make sure and disable ASF on all chip types. Otherwise, there may be
random reboots.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

There should never be descriptor error unless hardware or driver is buggy.
But if an error occurs, print useful information, clear irq, and recover.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This device is having all sorts of problems that lead to data corruption
and system instability.  It gets receive status and data out of order,
it generates descriptor and TSO errors, etc.

Until the problems are resolved, it should not be used by anyone
who cares about there system.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The workaround Yukon EC-U wasn't comparing with correct
version and wasn't doing correct setup. Without it, 88e8056
throws all sorts of errors.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Some of these chips are disabled until clock is enabled.
This fixes:
     http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=404107Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Driver needs to turn off carrier when down.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

On Yukon FE, occasional hardware receive checksum errors are seen.
An early indication of the problem is single bit differences in the two
checksum engines.  Use this as a detection mechanism to turn off Rx
checksumming.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch splits the vlan_group struct into a multi-allocated struct. On
x86_64, the size of the original struct is a little more than 32KB, causing
a 4-order allocation, which is prune to problems caused by buddy-system
external fragmentation conditions.

I couldn't just use vmalloc() because vfree() cannot be called in the
softirq context of the RCU callback.
Signed-off-by: NDan Aloni <da-x@monatomic.org>
Acked-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

New version.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>