提交 fc99fe06 编写于 作者: S Stephen Hemminger 提交者: Jeff Garzik

sky2: Add PCI device specfic register 4 & 5

Need to setup more PCI control control registers are on Yukon EX.
Some of these also exist on Yukon EC-U as well.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
上级 3ead5db7
......@@ -217,13 +217,19 @@ static void sky2_power_on(struct sky2_hw *hw)
sky2_write8(hw, B2_Y2_CLK_GATE, 0);
if (hw->chip_id == CHIP_ID_YUKON_EC_U || hw->chip_id == CHIP_ID_YUKON_EX) {
u32 reg1;
u32 reg;
sky2_pci_write32(hw, PCI_DEV_REG3, 0);
reg1 = sky2_pci_read32(hw, PCI_DEV_REG4);
reg1 &= P_ASPM_CONTROL_MSK;
sky2_pci_write32(hw, PCI_DEV_REG4, reg1);
sky2_pci_write32(hw, PCI_DEV_REG5, 0);
reg = sky2_pci_read32(hw, PCI_DEV_REG4);
/* set all bits to 0 except bits 15..12 and 8 */
reg &= P_ASPM_CONTROL_MSK;
sky2_pci_write32(hw, PCI_DEV_REG4, reg);
reg = sky2_pci_read32(hw, PCI_DEV_REG5);
/* set all bits to 0 except bits 28 & 27 */
reg &= P_CTL_TIM_VMAIN_AV_MSK;
sky2_pci_write32(hw, PCI_DEV_REG5, reg);
sky2_pci_write32(hw, PCI_CFG_REG_1, 0);
}
}
......
......@@ -14,6 +14,8 @@ enum {
PCI_DEV_REG3 = 0x80,
PCI_DEV_REG4 = 0x84,
PCI_DEV_REG5 = 0x88,
PCI_CFG_REG_0 = 0x90,
PCI_CFG_REG_1 = 0x94,
};
enum {
......@@ -28,6 +30,7 @@ enum {
enum pci_dev_reg_1 {
PCI_Y2_PIG_ENA = 1<<31, /* Enable Plug-in-Go (YUKON-2) */
PCI_Y2_DLL_DIS = 1<<30, /* Disable PCI DLL (YUKON-2) */
PCI_SW_PWR_ON_RST= 1<<30, /* SW Power on Reset (Yukon-EX) */
PCI_Y2_PHY2_COMA = 1<<29, /* Set PHY 2 to Coma Mode (YUKON-2) */
PCI_Y2_PHY1_COMA = 1<<28, /* Set PHY 1 to Coma Mode (YUKON-2) */
PCI_Y2_PHY2_POWD = 1<<27, /* Set PHY 2 to Power Down (YUKON-2) */
......@@ -67,6 +70,80 @@ enum pci_dev_reg_4 {
| P_ASPM_CLKRUN_REQUEST | P_ASPM_INT_FIFO_EMPTY,
};
/* PCI_OUR_REG_5 32 bit Our Register 5 (Yukon-ECU only) */
enum pci_dev_reg_5 {
/* Bit 31..27: for A3 & later */
P_CTL_DIV_CORE_CLK_ENA = 1<<31, /* Divide Core Clock Enable */
P_CTL_SRESET_VMAIN_AV = 1<<30, /* Soft Reset for Vmain_av De-Glitch */
P_CTL_BYPASS_VMAIN_AV = 1<<29, /* Bypass En. for Vmain_av De-Glitch */
P_CTL_TIM_VMAIN_AV_MSK = 3<<27, /* Bit 28..27: Timer Vmain_av Mask */
/* Bit 26..16: Release Clock on Event */
P_REL_PCIE_RST_DE_ASS = 1<<26, /* PCIe Reset De-Asserted */
P_REL_GPHY_REC_PACKET = 1<<25, /* GPHY Received Packet */
P_REL_INT_FIFO_N_EMPTY = 1<<24, /* Internal FIFO Not Empty */
P_REL_MAIN_PWR_AVAIL = 1<<23, /* Main Power Available */
P_REL_CLKRUN_REQ_REL = 1<<22, /* CLKRUN Request Release */
P_REL_PCIE_RESET_ASS = 1<<21, /* PCIe Reset Asserted */
P_REL_PME_ASSERTED = 1<<20, /* PME Asserted */
P_REL_PCIE_EXIT_L1_ST = 1<<19, /* PCIe Exit L1 State */
P_REL_LOADER_NOT_FIN = 1<<18, /* EPROM Loader Not Finished */
P_REL_PCIE_RX_EX_IDLE = 1<<17, /* PCIe Rx Exit Electrical Idle State */
P_REL_GPHY_LINK_UP = 1<<16, /* GPHY Link Up */
/* Bit 10.. 0: Mask for Gate Clock */
P_GAT_PCIE_RST_ASSERTED = 1<<10,/* PCIe Reset Asserted */
P_GAT_GPHY_N_REC_PACKET = 1<<9, /* GPHY Not Received Packet */
P_GAT_INT_FIFO_EMPTY = 1<<8, /* Internal FIFO Empty */
P_GAT_MAIN_PWR_N_AVAIL = 1<<7, /* Main Power Not Available */
P_GAT_CLKRUN_REQ_REL = 1<<6, /* CLKRUN Not Requested */
P_GAT_PCIE_RESET_ASS = 1<<5, /* PCIe Reset Asserted */
P_GAT_PME_DE_ASSERTED = 1<<4, /* PME De-Asserted */
P_GAT_PCIE_ENTER_L1_ST = 1<<3, /* PCIe Enter L1 State */
P_GAT_LOADER_FINISHED = 1<<2, /* EPROM Loader Finished */
P_GAT_PCIE_RX_EL_IDLE = 1<<1, /* PCIe Rx Electrical Idle State */
P_GAT_GPHY_LINK_DOWN = 1<<0, /* GPHY Link Down */
PCIE_OUR5_EVENT_CLK_D3_SET = P_REL_GPHY_REC_PACKET |
P_REL_INT_FIFO_N_EMPTY |
P_REL_PCIE_EXIT_L1_ST |
P_REL_PCIE_RX_EX_IDLE |
P_GAT_GPHY_N_REC_PACKET |
P_GAT_INT_FIFO_EMPTY |
P_GAT_PCIE_ENTER_L1_ST |
P_GAT_PCIE_RX_EL_IDLE,
};
#/* PCI_CFG_REG_1 32 bit Config Register 1 (Yukon-Ext only) */
enum pci_cfg_reg1 {
P_CF1_DIS_REL_EVT_RST = 1<<24, /* Dis. Rel. Event during PCIE reset */
/* Bit 23..21: Release Clock on Event */
P_CF1_REL_LDR_NOT_FIN = 1<<23, /* EEPROM Loader Not Finished */
P_CF1_REL_VMAIN_AVLBL = 1<<22, /* Vmain available */
P_CF1_REL_PCIE_RESET = 1<<21, /* PCI-E reset */
/* Bit 20..18: Gate Clock on Event */
P_CF1_GAT_LDR_NOT_FIN = 1<<20, /* EEPROM Loader Finished */
P_CF1_GAT_PCIE_RX_IDLE = 1<<19, /* PCI-E Rx Electrical idle */
P_CF1_GAT_PCIE_RESET = 1<<18, /* PCI-E Reset */
P_CF1_PRST_PHY_CLKREQ = 1<<17, /* Enable PCI-E rst & PM2PHY gen. CLKREQ */
P_CF1_PCIE_RST_CLKREQ = 1<<16, /* Enable PCI-E rst generate CLKREQ */
P_CF1_ENA_CFG_LDR_DONE = 1<<8, /* Enable core level Config loader done */
P_CF1_ENA_TXBMU_RD_IDLE = 1<<1, /* Enable TX BMU Read IDLE for ASPM */
P_CF1_ENA_TXBMU_WR_IDLE = 1<<0, /* Enable TX BMU Write IDLE for ASPM */
PCIE_CFG1_EVENT_CLK_D3_SET = P_CF1_DIS_REL_EVT_RST |
P_CF1_REL_LDR_NOT_FIN |
P_CF1_REL_VMAIN_AVLBL |
P_CF1_REL_PCIE_RESET |
P_CF1_GAT_LDR_NOT_FIN |
P_CF1_GAT_PCIE_RESET |
P_CF1_PRST_PHY_CLKREQ |
P_CF1_ENA_CFG_LDR_DONE |
P_CF1_ENA_TXBMU_RD_IDLE |
P_CF1_ENA_TXBMU_WR_IDLE,
};
#define PCI_STATUS_ERROR_BITS (PCI_STATUS_DETECTED_PARITY | \
PCI_STATUS_SIG_SYSTEM_ERROR | \
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册