This isn't perfect but at least solves the problem of pm.c's dependency
on register definitions in <mach/lubbock.h>, which doesn't make much
sense.
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Move the processor specific initialization (largely resources initialization)
out of soc_common_drv_pcmcia_probe() into dedicated sa11xx_drv_pcmcia_probe()
and __pxa2xx_drv_pcmcia_probe().

By doing this, we are now able to move the PCMCIA related definitions out of
pxa-regs.h and back into pxa2xx_base.c.

As a result, remove that reference of _PCMCIA1IO in arch/arm/mach-pxa/viper.c.
Signed-off-by: NEric Miao <eric.miao@marvell.com>

pxa-regs.h and hardware.h are not intended for use directly in driver
code, remove those unnecessary references.
Signed-off-by: NEric Miao <eric.miao@marvell.com>

The only things prevent drivers/serial/pxa.c from being generic enough
are:

  1. IER_UUE which can be safely replaced by UART_IER_UUE as defined in
     serial_reg.h for PXA

  2. __PREG() and FFUART/BTUART/STUART definitions to decide the UART
     port name

And removed the un-necessary #include of <mach/...> and <asm/...> headers.
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Let's handle GPIOs by banks, each bank covers up to 32 GPIOs with one set
of registers, and each set of registers start from different offsets.

           GPLR    GPDR    GPSR    GPCR    GRER    GFER    GEDR
 BANK 0 - 0x0000  0x000C  0x0018  0x0024  0x0030  0x003C  0x0048
 BANK 1 - 0x0004  0x0010  0x001C  0x0028  0x0034  0x0040  0x004C
 BANK 2 - 0x0008  0x0014  0x0020  0x002C  0x0038  0x0044  0x0050

 BANK 3 - 0x0100  0x010C  0x0118  0x0124  0x0130  0x013C  0x0148
 BANK 4 - 0x0104  0x0110  0x011C  0x0128  0x0134  0x0140  0x014C
 BANK 5 - 0x0108  0x0114  0x0120  0x012C  0x0138  0x0144  0x0150

 NOTE:
   BANK 3 is only available on PXA27x and later processors.
   BANK 4 and 5 are only available on PXA935

1. introduce GPIO_BANK(n) for the offset base of each bank

2. 'struct pxa_gpio_chip' is expanded to include IRQ edge and mask
   setings, and saved register values as well, and is dynamically
   allocated due to possible bank number ranging from 3 to 6

3. all accesses to GPIO registers are made through 'regbase' within
   'pxa_gpio_chip', and register offset

4. introduce several inline functions to simplify the code a bit

5. change IRQ demux handler to base on gpio chips
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Signed-off-by: NEric Miao <eric.miao@marvell.com>

This makes gpio.c fully independent of pxa-regs.h (except for the
virtual address of the registers).
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Looks like we have to live with pxa_gpio_mode() for a while, giving
its presence is actually making gpio.c not generic enough, let's
move it temporarily outside before it can be fully purged.
Signed-off-by: NEric Miao <eric.miao@marvell.com>

This is part of the work making gpio.c generic enough, the changes
include:

1. move IRQ handling of GPIO 0 and 1 outside (and back into irq.c)

2. pxa_init_gpio() accepts a range for muxed GPIO IRQs, and an IRQ
   number for the muxed GPIOs

3. __gpio_is_occupied() and __gpio_is_inverted() are made inline,
   and are moved into <mach/gpio.h> instead of generic gpio.c
Signed-off-by: NEric Miao <eric.miao@marvell.com>

1. Driver code where pxa_request_dma() is called will most likely
   reference DMA registers as well,  and it is really unnecessary
   to include pxa-regs.h just for this. Move the definitions into
   <mach/dma.h> and make relevant drivers include it instead of
   <mach/pxa-regs.h>.

2. Introduce DMAC_REGS_VIRT as the virtual address base for these
   DMA registers. This allows later processors to re-use the same
   IP while registers may start at different I/O address.
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Signed-off-by: NEric Miao <eric.miao@marvell.com>

Considering the header mess ATM, it is not always possible to include
the correct header files within board code. Let's keep this simple:

  <mach/pxa25x.h>  - for pxa25x based platforms
  <mach/pxa27x.h>  - for pxa27x based platforms
  <mach/pxa300.h>  - for pxa300 based platforms
  <mach/pxa320.h>  - for pxa320 based platforms
  <mach/pxa930.h>  - for pxa930 based platforms

NOTE:

1. one header one board file, they are not compatible (i.e. they have
   conflicting definitions which won't compile if included together).

2. Unless strictly necessary, the following header files are considered
   to be SoC files use _only_, and is not recommended to be included in
   board code:

    <mach/hardware.h>
    <mach/pxa-regs.h>
    <mach/pxa2xx-regs.h>
    <mach/pxa3xx-regs.h>
    <mach/mfp.h>
    <mach/mfp-pxa2xx.h>
    <mach/mfp-pxa25x.h>
    <mach/mfp-pxa27x.h>
    <mach/mfp-pxa3xx.h>
    <mach/mfp-pxa300.h>
    <mach/mfp-pxa320.h>
    <mach/mfp-pxa930.h>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Default to the same behaviour as the shipped WinCE system.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

so they can be shared with gpio_vbus.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Fixes an off-by-one error.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Add m2p dma support to the ep93xx
Signed-off-by: NRyan Mallon <ryan@bluewatersys.com>
Acked-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add the clocks for ep93xx m2p dma engine.
Signed-off-by: NRyan Mallon <ryan@bluewatersys.com>
Acked-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

SCALE: add ice dcc support

Tested on the ixp425 with the ice PEEDI
Ack-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Conflicts:

	arch/arm/plat-mxc/dma-mx1-mx2.c

We should not be modifying the scatterlist passed to us from the
driver code; doing so breaks assumptions made by the DMA API code,
and could cause problems if the driver retries a transfer using an
old scatterlist.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

There's no point these being in a generic include file when they're
only used in arch/arm/mach-rpc/dma.c.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The AT91SAM20-EK has a WM8731 attached to it with MCLK supplied from
PCLK0 and the digital audio interface supplied by SSC0.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NDmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Code has never been in buildable state since initial
merge.
Signed-off-by: NDmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Remove the unneeded #include <mach/hardware.h>
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch adds the platform_device and resource structures for the USB
ISP1761 chip, usable with the in-kernel isp1760 driver.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This driver adds the platform_device definitions to allow the use of
CompactFlash on the RealView PB11MPCore and PB-A8 platforms. Note that
the CompactFlash controller is expected to be initialised by the Boot
Monitor and support the True IDE mode.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This chip is on the I2C bus on the RealView and Versatile boards. The
patch adds the i2c_board_info definition for this device and registers
it with the I2C subsystem.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

If dev->id is not -1, the platform code may use static bus numbering
rather than dynamic. The patch also changes the i2c_versatile_init to a
subsys_initcall rather than module_init to make sure it is initialised
before the I2C devices initialisation.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This includes a new defconfig for the Shark and some changes to
the mach-shark directory to avoid namespace pollution and to
switch the rtc to the newer driver.
Signed-off-by: NAlexander Schulz <alex@shark-linux.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Ensure that the LCD engine is correctly re-initialised
and the correct parameters passed ot s3c2410fb_init_registers.
Signed-off-by: NSimtec Linux Team <linux@simtec.co.uk>
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Ensure __iomem attribute is __force 'd off in the minimal
__raw_writel() implementation.
Signed-off-by: NSimtec Linux Team <linux@simtec.co.uk>
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch also makes the frame pointer default to y only if
!ARM_UNWIND. LOCKDEP no longer selects FRAME_POINTER if ARM_UNWIND is
enabled.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This is needed to allow or stop the unwinding at certain points in the
kernel like exception entries.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch adds ELF section parsing for the unwinding tables in loadable
modules together with the PREL31 relocation symbol resolving.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch adds the main functionality for parsing the stack unwinding
information generated by the ARM EABI toolchains. The unwinding
information consists of an index with a pair of words per function and a
table with unwinding instructions. For more information, see "Exception
Handling ABI for the ARM Architecture" at:

http://infocenter.arm.com/help/topic/com.arm.doc.subset.swdev.abi/index.htmlSigned-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>