In some corner cases, (invalid) 11g rates were used while
working on 11a band.

Take care of it by initializing rate_set according to the
configured band.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

There was a check preventing 127x devices from using the 11a band when
operating as AP. Since we now support this functionality, remove the
check.

With this patch, a 11a AP starts ok on 127x cards.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Add tx_spare_blocks member to the wl1271 struct
for more generic configuration of the amount
of spare TX blocks that should be used.
The default value is 1.
In case GEM cipher is used by the STA, we need
2 spare TX blocks instead of just 1.
Signed-off-by: NGuy Eilam <guy@wizery.com>
Acked-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Only increment the queue count after actually queuing the skb. This
avoids a spurious increment is case of dropped packets.

Also move the Tx-watermark checking code after the packet is enqueued.
This makes the count more accurate - it includes the just-queued
packet.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Don't pollute the queues with Tx directed to invalid stations. This
can happen during recovery.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

This fix eliminates a potential race between starting the AP role
and setting encryption keys.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

This adjusts FW TX block allocation for connected stations in PS.
Firmware congestion is measured in allocated packets instead of blocks.

Allow a link in PS to queue up to 2 packets to the FW.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Sometimes the fw doesn't send the DISCONNECT_EVENT_COMPLETE_ID
on station role stop, so don't wait for it.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

When the FW Tx released blocks counter wraps around, we should correct
our calculation of released blocks. Otherwise we add a large negative
figure to our driver freed blocks counter
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

When selecting packets for transmission, prefer the ACs that are least
occupied in the FW. When packets for multiple ACs are present in the FW,
it decides which to transmit according to WMM QoS parameters.

With these changes, lower priority ACs should not be starved when higher
priority traffic is present.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Track the number of freed packets in each AC when receiving an interrupt
from the FW. This paves the way for tracking allocated packets per AC.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

When wep key was removed after disconnection, sta_hlid was invalid,
and it resulted in a fw crash.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

when the key was recorded, wl->ap_bcast_hlid was invalid
(since the role wasn't started), so when configuring the
key we need to use the current ap_bcast_hlid.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Unconditionally configure HT rate support to the FW on all ACs
when starting the AP.

When 11n support is disabled by usermode (hostapd), each STA joining
the AP will appear as a non-HT STA. This will stop us from accidentally
transmitting using MCS rates.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

When a new STA joins the BSS, configure the HT rates it supports to the
FW.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

In addition, set global HT operation mode via ACX_HT_BSS_OPERATION when
a change is detected by usermode
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Start IBSS role when the interface type is IBSS.
As with sta role, use the dev role until the role
is started.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Add wl12xx_cmd_role_start_ibss() implementation and defintion.
This function is used in order to start the IBSS role.

Stopping the IBSS is done by using the same api as stop STA,
so there is no need for a separate function.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

If hlid was already removed, there is no need to remove
its key (it might cause a fw crash, as the key is invalid).
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

After adding a station, call wl12xx_cmd_set_peer_state().
This is required for 11n support.

Change wl12xx_cmd_set_peer_state() prototype to get hlid
as param.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Incorporate interface changes for HT support.

Add ba_bitmap field to the wl1271_link struct, to indicate
activate RX BA sessions (for AP mode).
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Using hlid=0 in AP mode is a bug. Dynamically allocate HLIDs.

Set the "first sta hlid" as 3. This will have to be changed
when multiple vifs will be supported.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Increment the session counter on every
wl12xx_cmd_role_start_sta() command.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The BT coex params api have been changed.
Update it, and init coex for both sta and ap.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The ROC command asks the fw stay on the channel of the given
hlid. it currently has 2 primary functions:

1. Allow tx/rx from the device role.

In order to tx/rx packets while the stations is not associated
(e.g. auth req/resp), the device role has to be used, along
with ROC on its link.

Keep the logic similiar to the one used in dummy_join. However,
since we can't scan while we ROC, we add CROC before starting
a scan, and ROC again (if needed) on scan complete.

2. Keeping the antenna for a specific link.

We ROC until the connection was completed (after EAPOLs exchange)
in order to prevent BT coex operations from taking the antenna
and failing the connection (after this stage, psm can be used).

During association, we ROC on the station role, and then CROC
the device role, thus assuring being ROC during all the connection
process.

Delete the WL1271_FLAG_JOINED flag, and use a roc bitmap
to indicate what roles are currently ROCed.

Add wl12xx_roc/croc functions in order to wrap the roc/croc
commands while taking care of the roc bitmap.

The current ROC/CROC state-machine is a bit complicated. In
the future we'll probably want to use wpa_supplicant to control
the ROC during connection.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Allow handling of DUMMY_PACKET_EVENT_ID also in ap mode.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Add structs and functions to support the ROC/CROC commands.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

system_hlid is a const hlid (always 0), used by the fw and driver
for packets which are not bound to specific role (e.g. dynamic
memory packets).
indicate it as always allocated.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Configure rate management parameters on hw init
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Use ACX_BEACON_FILTER_OPT for both station and ap roles
(use the generic wl1271_acx_beacon_filter_opt()
instead of wl1271_acx_set_ap_beacon_filter() ).
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The max template size was increased in the new fw.
However, we should use the max size only when needed, as it
consumes some of the chip's memory.

Thus, by default initialize the templates to the default size.
Initialize to the maximum size only when required.

Use WL1271_CMD_TEMPL_DFLT_SIZE instead of some of the
predefined structs, as some of them didn't account
for additional IEs that might be added to the template.

Delete structs defintions not used after these changes.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Update the rx/tx descriptors according to the new fw api
(fw >= 6/7.3.0.0.75)
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Update the scan command to use the new fw api
(fw 6/7.3.0.0.75).
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The device role is a special role used for rx and tx frames
prior to association (as the STA role can get packets only
from its associated bssid)

Since this role is required for the sta association process,
we enable it when a new sta interface is created.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

According to the new multi-role flow, we have to enable the
role before using (starting) it, and disable it on cleanup
(after it's no longer needed).
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Change the commands and events according to the new fw api
(fw >= 6/7.3.0.0.75).

The main change is the replacement of JOIN/DISCONNECT commands,
with ROLE_START/ROLE_STOP commands.

The use of these commands should be preceded by the ROLE_ENABLE
command (allocating role resources), and followed by the
ROLE_DISABLE command (freeing role resources).
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Update the acx commands according to the new fw api
(fw >= 6/7.3.0.0.75).

The main change in most of the ACXs is the addition
of a new role_id/link_id field, which is required
for multi-role operation.

Currently, we don't really support multi-role, as
most of our data (inside wl) is global.
As the current fw doesn't support concurrent roles
yet, keep it this way and add wl->role_id and
wl->sta_hlid to save the active role/link.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Update the fw status struct according to the new fw api
(fw >= 6/7.0.0.35).
All the roles use the same struct now.

The memory accounting was changed a bit according to
the struct changes.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The new fw doesn't support rx_filtering configuration (as a
stand-alone command. the rx filtering is done automatically
according to the active role).
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

In order to keep to driver compiling during the patchset,
while avoiding one-huge-patch, temporarily disable some
advanced ap functions.

These changes will be reverted later in the patchset, as
part of the patches for advanced ap functions support.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>