This patch proposes to remove the IRQF_DISABLED flag from Davinci code ;)
It's a NOOP since 2.6.35, and will be removed one day
Signed-off-by: NMichael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Register  gpio platform device on DA8XX boards.

While at it, group related include files together.
Signed-off-by: NPhilip Avinash <avinashphilip@ti.com>
[nsekhar@ti.com: remove SoC specific parts from this file.
		 fix compile warnings]
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

"struct davinci_uart_config" was introduced to specify
UART ports brought out or enabled on the board. But
none of the boards use it for that purpose and we are
not going to add anymore board files, so remove the
structure.
Signed-off-by: NManjunathappa, Prakash <prakash.pm@ti.com>
Suggested-by: NSekhar Nori <nsekhar@ti.com>
[nsekhar@ti.com: split patch to remove davinci_serial_setup_clk()
		 changes.]
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Remove specifying mmc controller IP version information via platform
data, instead specify device name so that driver derives it from
platform_device_id table. Also change the clock node name to match
the changed dev_id.
Tested on da850-evm to make sure driver loads without clk_get failures.
Signed-off-by: NManjunathappa, Prakash <prakash.pm@ti.com>
Reviewed-by: NSekhar Nori <nsekhar@ti.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NChris Ball <cjb@laptop.org>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

This patches replaces #if defined() by IS_ENABLED macro, which provides
better readability.
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Without this patch, da8xx_register_spi() registers the SPI board info,
the SPI controller, and sets its number of chipselect to the size of the
static spi_board_info array. This is bad because a SPI board info may
declare devices for different SPI buses, and because other code can also
call spi_register_board_info() (e.g. a daughter board might provide
additional SPI devices).

This patch removes the spi_register_board_info() call from
da8xx_register_spi(), renames this last one to da8xx_register_spi_bus()
to be more explicit, takes the number of chipselect as a function
parameter, and updates the impacted board-da8{3,5}0-evm.c, and
board-mityomapl138.c files accordingly. It also sets the SPI platform
data static, as it doesn't need to be exported.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
[nsekhar@ti.com: fixed conflicts with v3.7-rc7, converted to use pr_warn(),
modified print messages to use __func__]
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Now that the only field in struct sys_timer is .init, delete the struct,
and replace the machine descriptor .timer field with the initialization
function itself.

This will enable moving timer drivers into drivers/clocksource without
having to place a public prototype of each struct sys_timer object into
include/linux; the intent is to create a single of_clocksource_init()
function that determines which timer driver to initialize by scanning
the device dtree, much like the proposed irqchip_init() at:
http://www.spinics.net/lists/arm-kernel/msg203686.html

Includes mach-omap2 fixes from Igor Grinberg.
Tested-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.

This moves such data out of the davinci include directories
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NNicolas Pitre <nico@linaro.org>
Acked-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: "Ben Dooks" <ben-linux@fluff.org>
Cc: "Wolfram Sang" <w.sang@pengutronix.de>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Liam Girdwood <lrg@ti.com>
Cc: davinci-linux-open-source@linux.davincidsp.com

Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NSekhar Nori <nsekhar@ti.com>

Rather than using DaVinci specific davinci_soc_info based
restart hook, use the restart hook available in the machine
descriptor instead.

Tested on DM365 and AM18x EVMs.

v2:
Changed to use restart hook in machine descriptor
per Russell's comment.
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Recall the recently added prefix requirements:
 * "NAND_" for flags in nand.h, used in nand_chip.options
 * "NAND_BBT_" for flags in bbm.h, used in nand_chip.bbt_options
        or in nand_bbt_descr.options

Thus, I am changing NAND_USE_FLASH_BBT to NAND_BBT_USE_FLASH.

Again, this flag is found in bbm.h and so should NOT be used in the
"nand_chip.options" field.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>

This patch works with the following three flags from two headers (nand.h
and bbm.h):
  (1) NAND_USE_FLASH_BBT (nand.h)
  (2) NAND_USE_FLASH_BBT_NO_OOB (nand.h)
  (3) NAND_BBT_NO_OOB (bbm.h)

These flags are all related and interdependent, yet they were in
different headers. Flag (2) is simply the combination of (1) and (3) and
can be eliminated.

This patch accomplishes the following:
  * eliminate NAND_USE_FLASH_BBT_NO_OOB (i.e., flag (2))
  * move NAND_USE_FLASH_BBT (i.e., flag (1)) to bbm.h

It's important to note that because (1) and (3) are now both found in
bbm.h, they should NOT be used in the "nand_chip.options" field.

I removed a small section from the mtdnand DocBook because it referes to
NAND_USE_FLASH_BBT in nand.h, which has been moved to bbm.h.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>

Signed-off-by: NNicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>

Signed-off-by: NNicolas Pitre <nicolas.pitre@linaro.org>

This patch adds the on-board SPI flash device to the
DA830/OMAP-L137/AM17x EVM. It also registers the SPI flash
device to the MTD subsystem.

Based on SPI flash device support for MityDSP-L138F platform.
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
[michael.williamson@criticallink.com: moved da830evm_spi0_pdata to devices-da8xx.c]
[michael.williamson@criticallink.com: moved da830evm_init_spi0 to devices-da8xx.c]
Signed-off-by: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

Since we're now using addruart to establish the debug mapping, we can
remove the io_pg_offst and phys_io members of struct machine_desc.

The various declarations were removed using the following script:

  grep -rl MACHINE_START arch/arm | xargs \
  sed -i '/MACHINE_START/,/MACHINE_END/ { /\.\(phys_io\|io_pg_offst\)/d }'

[ Initial patch was from Jeremy Kerr, example script from Russell King ]
Signed-off-by: NNicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Eric Miao <eric.miao at canonical.com>

This patch removes davinci architecture code that has now been rendered
useless by the previous patches in the MDIO separation series.

In addition, the earlier phy_mask definitions have been replaced with
corresponding phy_id definitions.
Signed-off-by: NCyril Chemparathy <cyril@ti.com>
Tested-by: NMichael Williamson <michael.williamson@criticallink.com>
Tested-by: NCaglar Akyuz <caglarakyuz@gmail.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This patch adds machine checks in the serial console init routines
for the DA8XX EVM boards.  This is needed because there are other
DA8XX based machines that use a different UART/tty as the console
and may be included in a common kernel build.
Signed-off-by: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Setup the NAND flash timings for DA830 EVM.

Before configuring the timing values, throughput calculation
using dd command yielded 477 kB/s write and 970 kB/s read speed.

After the timing configuration, the throughput was measured to
be 2.5 MB/s write and 5.1 MB/s read.

[Mukul Bhatnagar: actual calculation of timing values from the
NAND datasheet]
Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Mukul Bhatnagar <mbhatnagar@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The Sitara AM17x SoCs from TI are an OMAP-L137 pin-to-pin
compatible ARM9 microprocessor offering from TI.

The Sitara AM18x SoCs from TI are an OMAP-L138 pin-to-pin
compatible ARM9 microprocessor offering from TI.

More information about these processors available at:
www.ti.com/am1x

Because of their compatibiliy with OMAP-L1x, the kernel
support for OMAP-L1x is fully relevant to AM1x processors.

This patch updates the Kconfig prompt and help text to include
the AM1x part names to help users select configurations required
for these parts easily.

Also, the hardware information that shows up in /proc/cpuinfo
is updated to show applicability of the respective OMAP-L1x EVMs
for AM1x parts.
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The drivers on da8xx/omapl EVMs do not utilize all the channels
and slots provided by EDMA. Some of these are better utilitzed by
the DSP on the SoC for speeding up codec operations.

Reserve these channels/slots for the DSP.
Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Currently the EDMA queue to be used by for servicing ASP through
internal RAM is fixed to EDMAQ_0 and that to service internal RAM
from external RAM is fixed to EDMAQ_1.

This may not be the desirable configuration on all platforms. For
example, on DM365, queue 0 has large fifo size and is more suitable
for video transfers. Having audio and video transfers on the same
queue may lead to starvation on audio side.

platform data as defined currently passes a queue number to the driver
but that remains unused inside the driver.

Fix this by defining one queue each for ASP and RAM transfers in the
platform data and using it inside the driver.

Since EDMAQ_0 maps to 0, thats the queue that will be used if
the asp queue number is not initialized. None of the platforms
currently utilize ping-pong transfers through internal RAM so that
functionality remains unchanged too.

This patch has been tested on DM644x and OMAP-L138 EVMs.
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch implements the following:

 - interrupt initialization uses ioremap() instead of passing a virtual address
   via davinci_soc_info.

 - machine definitions directly point to cp_intc_init() or davinci_irq_init()

 - davinci_intc_type and davinci_intc_base now get initialized in controller
   specific init functions instead of davinci_common_init()

 - minor fix in davinci_irq_init() to use intc_irq_num instead of
   DAVINCI_N_AINTC_IRQ
Signed-off-by: NCyril Chemparathy <cyril@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The board file #define's its own version of EMIFA base addresses, while there
are DA8XX_AEMIF_*_BASE macros #define'd in <mach/da8xx.h>.  Start using them
instead.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Rename da8xx_pinmux_setup() to davinci_cfg_reg_list() and promote it for use in
other SOCs that may need the ability to configure multiple pins in one shot.
Signed-off-by: NCyril Chemparathy <cyril@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Host map configuration instructs the interrupt controller to route interrupt
channels to FIQ or IRQ lines.  Currently, DA8xx family of devices leave these
registers at their reset-default values.

TNETV107X however does not have sane reset defaults, and therefore this
architecture needs to reconfigure the host-map such that channels 0 and 1
go to FIQ, and the remaining channels raise IRQs.

This patch adds an optional host map argument to cp_intc_init() for this.
Signed-off-by: NCyril Chemparathy <cyril@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The merge for 2.6.34 brings in 8-bit support to the DaVinci MMC/SD driver.

This patch updates the platform data for DA830/OMAP-L137 EVM to use 8-wire
support available in the driver.
Signed-off-by: NVipin Bhandari <vipin.bhandari@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The DA830/OMAP-L137 EVM has GPIO based card detection logic, but the current
code does not use it.

Add support for GPIO based card detection to avoid reading the card to see
if a card is present or not.
Signed-off-by: NVipin Bhandari <vipin.bhandari@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

OMAP-L138 adds a second SYSCFG region having useful functionality
like deep sleep, pull up/down control and SATA clock stop.

This patch makes provision for accessing registers from second
SYSCFG region in da8xx code.

Note that OMAP-L137 has a single SYSCFG region.
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Include high speed capabilities in MMC/SD platform data
for DA830/OMAP-L137 and DA850/OMAP-L138 EVMs.
Signed-off-by: NChaithrika U S <chaithrika@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

When kernel is built with CONFIG_DEBUG_SECTION_MISMATCH=y
option, using da8xx_omapl_defconfig, some warnings are
observed:

WARNING: vmlinux.o(.text+0xc2a4): Section mismatch in reference
from the function da850_evm_setup_nor_nand() to the variable
.init.data:da850_nand_pins
The function da850_evm_setup_nor_nand() references
the variable __initdata da850_nand_pins.
This is often because da850_evm_setup_nor_nand lacks a __initdata
annotation or the annotation of da850_nand_pins is wrong.

This patch fixes such warnings.
Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

On the DA830, AEMIF and MMC/SD pins are shared. On the EVM, when
the mux_mode signal is low MMC/SD works and when mux_mode signal
is high, NAND works.

When MMC/SD driver is configured in the kernel, do not let NAND
get registered and drive mux_mode high. Instead, print a warning
for user to understand why the platform device for NAND did not
get registered.
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This patch supports runtime detection of DA830 UI card and
eliminates the need for DA830_UI config option. Successful
probe of GPIO expander present on the UI card is used to
detect its presence. For this reason, GPIO_PCF857X is auto-
selected when DA830 EVM is configured. In case the UI card
is absent, the probe fails in reasonable time.

As a side effect this patch also gets rid of the voilation
of Documentation/SubmittingPatches section 2.2 in function
da830_evm_ui_expander_setup()
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Remove ifdefs inside da830_evm_init function since they are
discouraged in Documentation/SubmittingPatches section 2.2

Use the method outlined in that document for fixing it.

Tested on DA830 EVM.
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This patch fixes the following warning seen when building with default
config:

arch/arm/mach-davinci/board-da830-evm.c:371: warning: 'da830_evm_devices' defined but not used

Tested on DA830 EVM with and without CONFIG_DA830_UI_NAND enabled.
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Add support for NAND flash parts on the DA830/OMAP-L137 EVM
User Interface board.  This includes overriding the default
bad block tables used by the davinci_nand driver.
Signed-off-by: NDavid A. Griego <dgriego@mvista.com>
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Properly set up the OTG mode thru the CFGCHIP2 register, enable the
USB0_DRVVBUS pin, and finally register the MUSB platform device.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

There have accumulated quite a lot of them after the code reorganizations...

In several cases I had to replace #include <linux/dma-mapping.h> which wasn't
needed directly but happened to #include <linux/err.h> which was needed.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

All that is needed is the existing #include <linux/gpio.h>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The machine name string shows up in /proc/cpuinfo under 'Hardware' and
can be used by userspace apps.  Make the format consistent with the
DA850/OMAP-l138 EVM by adding the '-' between OMAP and L137.
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>