Use drm_atomic_helper_resume/suspend() and get rid off all the obsolete
register level context restoring code.
Signed-off-by: NJyri Sarha <jsarha@ti.com>

Enable and disable interrupts in crtc start() and stop(). None of the
interrupts can fire if CRTC is disabled, so it is cleaner - when
considering suspend/resume code etc. - to enable the interrupts when
CRTC is turned on and to disable them when CRTC is turned off.
Signed-off-by: NJyri Sarha <jsarha@ti.com>

Set DRIVER_ATOMIC and use atomic helpers and rename commit and prepare
crtc helpers to enable and disable. This makes the final jump to mode
setting, but there is lot of obsolete code to clean up.
Signed-off-by: NJyri Sarha <jsarha@ti.com>

Add drm_mode_config_reset() call to tilcdc_load(). This is need to
initialize atomic state variables at load time.
Signed-off-by: NJyri Sarha <jsarha@ti.com>

Add atomic mode config funcs. The atomic_commit implementation is a
copy-paste from drm_atomic_helper_commit(), leaving out the async
test. The similar copy-paste implementation appears to be used in many
other drivers too. The standard drm_atomic_helper_check() is used for
checking.

The drm_atomic_helper_check() can not be used in drm_mode_config_funcs
atomic_check() callback because the plane's check implementation may
update crtc state's ->mode_changed flag. Because of this the
drm_atomic_helper_check_modeset() has to be called once more after
drm_atomic_helper_check_planes() (see drm_atomic_helper_check_modeset()
documentation).
Signed-off-by: NJyri Sarha <jsarha@ti.com>

Fix tilcdc component master unloading. If a subcomponent module
(tda998x in this case) is unloaded before its master (tilcdc in this
case), it calls drm_put_dev() and it should not be called again by
the master when its module is unloaded. However component_master_del()
must still be called and the check if the drm_put_dev() has been
called must be in component_master_ops unbind() callback, not in
platform_driver remove() callback.
Signed-off-by: NJyri Sarha <jsarha@ti.com>

Restore old dpms state in pm_resume(). The dpms is turned off in
pm_suspend() and it should be restored to its original state in
pm_resume(). Without this patch the display is left blanked after a
suspend/resume cycle.

Fixes commit 614b3cfe ("drm/tilcdc: disable the lcd controller/dma
engine when suspend invoked")
Signed-off-by: NJyri Sarha <jsarha@ti.com>

We already have a fallback in place to fill out the unique from
dev->unique, which is set to something reasonable in drm_dev_alloc.

Which means we only need to have a special set_busid for pci devices,
to be able to care the backwards compat code for drm 1.1 around, which
libdrm still needs.

While developing and testing this patch things blew up in really
interesting ways, and the code is rather confusing in naming things
between the kernel code, ioctl #defines and libdrm. For the next brave
dragon slayer, document all this madness properly in the userspace
interface section of gpu.tmpl.

v2: Make drm_dev_set_unique static and update kerneldoc.

v3: Entire rewrite, plus document what's going on for posterity in the
gpu docbook uapi section.

v4: Drop accidental amdgpu hunk (Emil).

v5: Drop accidental omapdrm vblank counter change (Emil).

v6: Rebase on top of the sphinx conversion.

Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> (virt_gpu)
Reviewed-by: NEmil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>

No dev->struct_mutex anywhere to be seen.

Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464630800-30786-14-git-send-email-daniel.vetter@ffwll.ch

Use devm_kzalloc() and devm_kcalloc() for private data allocation at
driver load time.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add ratelimited prints on sync lost and FIFO underrun interrupts.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Removes the duplicate LCDC_INT_ENABLE_SET_REG-entry in registers array.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Fix interrupt enable/disable code for version 2 tilcdc. In version 2
tilcdc there is a separate register for disabling interrupts. Writing
0 to enable registers bits does not have any effect. The interrupt
clear register works the same way, writing 1 to specific bit disables
the interrupt and writing 0 does not have any effect.

The "bug" that is fixed here does not really do any harm since the
interrupts are enabled only once in the power up and disabled before
power down.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Get rid of complex ping-pong mechanism and replace it with simpler
single buffer flipping code.

The LCDC HW appears to be designed mainly static framebuffers in
mind. There are two modes of operation, either static single buffer,
or ping pong double buffering with two static buffers switching back
and forth. Luckily the framebuffer start address is fetched only in
the beginning of the frame and changing the address after that only
takes effect after the next vertical blank. The page flipping code can
simply write the address of the new framebuffer and the page is
flipped automatically after the next vertical blank. Using the ping
pong double buffering makes the flipping code way more complex and it
does not provide any benefit, so it is better to switch to single
buffer operation.

There is still one problem in updating the framebuffer dma address on
the fly. There are two registers defining the framebuffer dma area and
things may break if the dma address is fetched in while the registers
are are being updated.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
[Added description to the patch]
Signed-off-by: NJyri Sarha <jsarha@ti.com>

Disable crtc on unload. Call tilcdc_crtc_dpms() with DRM_MODE_DPMS_OFF
in the beginning of unload function.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
[Added description to the patch]
Signed-off-by: NJyri Sarha <jsarha@ti.com>

Cleanup runtime PM handling. Before the patch the usage of pm_runtime
calls was inconsistent and hard to follow. After the update the
pm_runtime calls are removed from set_scanout() and called around
major operations that access the HW. After the patch the DPMS code does
not have pm_runtime_forbid/allow calls any more and
pm_runtime_irq_safe() is not set anymore.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
[Added description to the patch]
Signed-off-by: NJyri Sarha <jsarha@ti.com>

Allocate suspend/resume register storage based on the actual number
registers the driver is aware of. The static allocation for register
storage had fallen behind badly.
Reported-by: NMichael Bode <michael@bumbleB.de>
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Fix build error when !CONFIG_CPU_FREQ
drivers/gpu/drm/tilcdc/tilcdc_drv.c: In function 'tilcdc_load':
drivers/gpu/drm/tilcdc/tilcdc_drv.c:327:1: error: label 'fail_put_clk' defined but not used [-Werror=unused-label]
 fail_put_clk:
 ^
Signed-off-by: NGrygorii Strashko <Grygorii.Strashko@linaro.org>
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

There is nothing special about tilcdc HW when the video memory is
concerned. Just using the standard drm helpers for implementation is
enough.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The LCD controller must be deactivated and all DMA transactions stopped
when the suspend power state is entered otherwise the PRCM causes the L3
bus to get stuck in transition state.

This commit forces the lcdc to be shut down and waits for all pending DMA
transactions to complete as part of the suspend handler for this driver.
Signed-off-by: NDarren Etheridge <detheridge@ti.com>
Tested-by: NDave Gerlach <d-gerlach@ti.com>
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The frame_done interrupt was only being enabled when the vsync
interrupts were being enabled by DRM.  However the frame_done is
used to determine if the LCD controller has successfully completed
the raster_enable, raster_disable commands and the vsync interrupts
are not always enabled during these operations.
Signed-off-by: NDarren Etheridge <detheridge@ti.com>
Tested-by: NDave Gerlach <d-gerlach@ti.com>
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

On BeagleBone Black if no HDMI monitor is connected and suspend
is requested a kernel panic will result:

root@am335x-evm:~# echo mem > /sys/power/state
[ 65.548710] PM: Syncing filesystems ... done.
[ 65.631311] Freezing user space processes ... (elapsed 0.006 seconds) done.
[ 65.648619] Freezing remaining freezable tasks ... (elapsed 0.005 seconds) done.
[ 65.833500] Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa30e004
[ 65.841692] Internal error: : 1028 [#1] SMP ARM
  <snip>
[ 66.105287] [<c03765f0>] (platform_pm_suspend) from [<c037b6d4>] (dpm_run_callback+0x34/0x70)
[ 66.114370] [<c037b6d4>] (dpm_run_callback) from [<c037ba84>] (__device_suspend+0x10c/0x2f4)
[ 66.123357] [<c037ba84>] (__device_suspend) from [<c037d004>] (dpm_suspend+0x58/0x218)
[ 66.131796] [<c037d004>] (dpm_suspend) from [<c008d948>] (suspend_devices_and_enter+0x9c/0x3c0)
[ 66.141055] [<c008d948>] (suspend_devices_and_enter) from [<c008de7c>] (pm_suspend+0x210/0x24c)
[ 66.150312] [<c008de7c>] (pm_suspend) from [<c008cabc>] (state_store+0x68/0xb8)
[ 66.158103] [<c008cabc>] (state_store) from [<c02e9654>] (kobj_attr_store+0x14/0x20)
[ 66.166355] [<c02e9654>] (kobj_attr_store) from [<c0185c70>] (sysfs_kf_write+0x4c/0x50)
[ 66.174883] [<c0185c70>] (sysfs_kf_write) from [<c018926c>] (kernfs_fop_write+0xb4/0x150)
[ 66.183598] [<c018926c>] (kernfs_fop_write) from [<c0122638>] (vfs_write+0xa8/0x180)
[ 66.191846] [<c0122638>] (vfs_write) from [<c01229f8>] (SyS_write+0x40/0x8c)
[ 66.199365] [<c01229f8>] (SyS_write) from [<c000e580>] (ret_fast_syscall+0x0/0x48)
[ 66.207426] Code: e595c210 e5932000 e59cc000 e08c2002 (e592c000)

This is because the lcdc module is not enabled when no monitor is detected
to save power.  However the suspend handler just blindly tries to save the
lcdc state by copying out the pertinent registers. However module is off
so no good things happen when you try and access it.

This patch only saves off the registers if the module is enabled, and
then only restores the registers on resume if they were saved off during
suspend.
Signed-off-by: NDarren Etheridge <detheridge@ti.com>
Tested-by: NDave Gerlach <d-gerlach@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Update tilcdc driver to set the state of the pins to:
- "default on resume
- "sleep" on suspend

By optionally putting the pins into sleep state in the suspend callback
we can accomplish two things.
- minimize current leakage from pins and thus save power,
- prevent the IP from driving pins output in an uncontrolled manner,
which may happen if the power domain drops the domain regulator.
Signed-off-by: NDave Gerlach <d-gerlach@ti.com>
Signed-off-by: NDarren Etheridge <detheridge@ti.com>
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Updating the tilcdc DRM driver code to calculate the LCD controller
pixel clock more accurately. Based on a suggested implementation by
Tomi Valkeinen.

The current code does not work correctly and produces wrong results
with many requested clock rates. It also oddly uses two different
clocks, a display pll clock and a divider clock (child of display
pll), instead of just using the clock coming to the lcdc.

This patch removes the use of the display pll clock, and rewrites the
code to calculate the clock rates. The idea is simply to request a
clock rate of pixelclock*2, as the LCD controller has an internal
divider which we set to 2.
Signed-off-by: NDarren Etheridge <detheridge@ti.com>
[Rewrapped description]
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Again since the drm core takes care of event unlinking/disarming this
is now just needless code.

v2: Fixup misplaced hunks.

Cc: Rob Clark <robdclark@gmail.com>
Acked-by: NDaniel Stone <daniels@collabora.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com> (v1)
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453756616-28942-13-git-send-email-daniel.vetter@ffwll.ch

The drm_fbdev_cma_init function always calls the
drm_helper_disable_unused_functions. Since it's part of the usual probe
process, all the drivers using that helper will end up having their encoder
and CRTC disable functions called at probe if their device has not been
reported as enabled.

This could be fixed by reading out from the registers the current state of
the device if it is enabled, but even that will not handle the case where
the device is actually disabled.

Moreover, the drivers using the atomic modesetting expect that their enable
and disable callback to be called when the device is already enabled or
disabled (respectively).

We can however fix this issue by moving the call to
drm_helper_disable_unused_functions out of drm_fbdev_cma_init and make the
drivers needing it (all the drivers calling drm_fbdev_cma_init and not
using the atomic modesetting) explicitly call it.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452785109-6172-14-git-send-email-maxime.ripard@free-electrons.comAcked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Drivers shouldn't clobber the passed in addfb ioctl parameters.
i915 was doing just that. To prevent it from happening again,
pass the struct around as const, starting all the way from
internal_framebuffer_create().
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

drm_vblank_count() returns the software counter. We should not pretend
it's the hw counter since we use the hw counter to figuere out what the
software counter value should be. So instead provide a new function
drm_vblank_no_hw_counter() for drivers that don't have a real hw
counter. The new function simply returns 0, which is about the only
thing it can do.

Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NVincent Abriou <vincent.abriou@st.com>
[danvet: s/int pipe/unsigned int pipe/ to follow Thierry's interface
change.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This continues the pattern started in commit cc1ef118 ("drm/irq:
Make pipe unsigned and name consistent"). This is applied to the public
APIs and driver callbacks, so pretty much all drivers need to be updated
to match the new prototypes.

Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Jianwei Wang <jianwei.wang.chn@gmail.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

tilcdc calls runtime PM get/put functions everywhere. Some of those
places will be called in irq context, crashing the driver.

As a quick fix, use pm_runtime_irq_safe() for tilcdc.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NJyri Sarha <jsarha@ti.com>

Add support for an external compontised DRM encoder. The external
encoder can be connected to tilcdc trough device tree graph binding.
The binding document for tilcdc has been updated. The current
implementation supports only tda998x encoder.

To be able to filter out the unsupported video modes the tilcdc driver
needs to hijack the external connectors helper functions. The tilcdc
installes new helper functions that are otherwise identical to
orignals, but the mode_valid() call-back check the mode first localy,
before calling the original call-back. The tilcdc dirver restores the
original helper functions before it is unbound from the external
device.

I got the idea and some lines of code from Jean-Francois Moine's
"drm/tilcdc: Change the interface with the tda998x driver"-patch.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Acked-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Remove tilcdc slave support for tda998x driver. The tilcdc slave
support would conflicts with componentized use of tda998x.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Acked-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The drm_fbdev_cma_hotplug_event() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Reviewed-by: NThierry Reding <thierry.reding@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

A platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The current error path calls tilcdc_unload() in case of an error to release
the resources. However, this is wrong because not all resources have been
allocated by the time an error occurs in tilcdc_load().

To fix it, this commit adds proper labels to bail out at the different
stages in the load function, and release only the resources actually allocated.
Tested-by: NDarren Etheridge <detheridge@ti.com>
Tested-by: NJohannes Pointner <johannes.pointner@br-automation.com>
Signed-off-by: NEzequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: NDave Airlie <airlied@redhat.com>

One step closer to dropping all the drm_bus_* code:
Add a driver->set_busid() callback and make all drivers use the generic
helpers. Nouveau is the only driver that uses two different bus-types with
the same drm_driver. This is totally broken if both buses are available on
the same machine (unlikely, but lets be safe). Therefore, we create two
different drivers for each platform during module_init() and set the
set_busid() callback respectively.
Signed-off-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Use module_init instead of late_initcall, as is the norm for modular
drivers.

module_init was used until 6e8de0bd
("drm/tilcdc: add encoder slave (v2)") changed it to a late_initcall,
but it does not explain why. Tests show it's working properly with
module_init.
Signed-off-by: NGuido Martínez <guido@vanguardiasur.com.ar>
Tested-by: NDarren Etheridge <detheridge@ti.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The TI tilcdc driver is designed with a notion of submodules. Currently,
at unload time, these submodules are iterated and destroyed.

Now that the tilcdc remove order is fixed, this can be handled perfectly
by the kernel using the device infrastructure, since each submodule
is a kernel driver itself, and they are only destroy()'ed at unload
time. Therefore we move the destroy() functionality to each submodule's
remove().

Also, remove some checks in the unloading process since the new code
guarantees the resources are allocated and need a release.
Signed-off-by: NGuido Martínez <guido@vanguardiasur.com.ar>
Tested-by: NDarren Etheridge <detheridge@ti.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Unregister resources in the correct order on tilcdc_drm_fini, which is
the reverse order they were registered during tilcdc_drm_init.

This also means unregistering the driver before releasing its resources.
Signed-off-by: NGuido Martínez <guido@vanguardiasur.com.ar>
Tested-by: NDarren Etheridge <detheridge@ti.com>
Cc: <stable@vger.kernel.org> #v3.9+
Signed-off-by: NDave Airlie <airlied@redhat.com>

The driver did not unregister the allocated framebuffer, which caused
memory leaks (and memory manager WARNs) when unloading. Also, the
framebuffer device under /dev still existed after unloading.

Add a call to drm_fbdev_cma_fini when unloading the module to prevent
both issues.
Signed-off-by: NGuido Martínez <guido@vanguardiasur.com.ar>
Tested-by: NDarren Etheridge <detheridge@ti.com>
Cc: <stable@vger.kernel.org> #v3.9+
Signed-off-by: NDave Airlie <airlied@redhat.com>