Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 19 2月, 2017 1 次提交
  3. 20 1月, 2017 1 次提交
  5. 14 12月, 2016 2 次提交
    • L
      Revert "nvme: add support for the Write Zeroes command" · cdb98c26
      由 Linus Torvalds 提交于 
      This reverts commit 6d31e3ba.

This causes bootup problems for me both on my laptop and my desktop.
What they have in common is that they have NVMe disks with dm-crypt, but
it's not the same controller, so it's not controller-specific.

Jens does not see it on his machine (also NVMe), so it's presumably
something that triggers just on bootup.  Possibly related to dm-crypt
and the fact that I mark my luks volume with "allow-discards" in
/etc/crypttab.

It's 100% repeatable for me, which made it fairly straightforward to
bisect the problem to this commit. Small mercies.

So we don't know what the reason is yet, but the revert is needed to get
things going again.
Acked-by: NJens Axboe <axboe@fb.com>
Cc: Chaitanya Kulkarni <chaitanya.kulkarni@hgst.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      cdb98c26
    • A
      ata: avoid probing NCQ Prio Support if not explicitly requested · 9f56eca3
      由 Adam Manzanares 提交于 
      Previously, when the ata device was being initialized we were
probing for NCQ prio support by checking the identify information
and also checking the log page that holds information about ncq prio
support.

This caused an error on an Intel HBA so the code is now updated to
only probe for NCQ prio support when the sysfs variable controlling
NCQ prio support is enabled.

tj: Update formatting, switch to spin_[un]lock_irq() and update
    locking a bit, use REVALIDATE instead of RESET, and return -EIO
    instead of -EINVAL on config failure.
Signed-off-by: NAdam Manzanares <adam.manzanares@wdc.com>
Signed-off-by: NTejun Heo <tj@kernel.org>
      9f56eca3
  7. 13 12月, 2016 24 次提交
  9. 12 12月, 2016 6 次提交
  11. 11 12月, 2016 6 次提交
    • W
      e1000: use disable_hardirq() for e1000_netpoll() · 31119129
      由 WANG Cong 提交于 
      In commit 02cea395 ("genirq: Provide disable_hardirq()")
Peter introduced disable_hardirq() for netpoll, but it is forgotten
to use it for e1000.

This patch changes disable_irq() to disable_hardirq() for e1000.
Reported-by: NDave Jones <davej@codemonkey.org.uk>
Suggested-by: NSabrina Dubroca <sd@queasysnail.net>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      31119129
    • K
      i40e: don't truncate match_method assignment · 0266ac45
      由 Keller, Jacob E 提交于 
      The .match_method field is a u8, so we shouldn't be casting to a u16,
and because it is only one byte, we do not need to byte swap anything.
Just assign the value directly. This avoids issues on Big Endian
architectures which would have byte swapped and then incorrectly
truncated the value.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Bimmy Pujari <bimmy.pujari@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      0266ac45
    • W
      net: ethernet: ti: netcp: add support of cpts · 6246168b
      由 WingMan Kwok 提交于 
      This patch adds support of the cpts device found in the
gbe and 10gbe ethernet switches on the keystone 2 SoCs
(66AK2E/L/Hx, 66AK2Gx).

Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: NWingMan Kwok <w-kwok2@ti.com>
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      6246168b
    • T
      net: phy: phy drivers should not set SUPPORTED_[Asym_]Pause · 529ed127
      由 Timur Tabi 提交于 
      Instead of having individual PHY drivers set the SUPPORTED_Pause and
SUPPORTED_Asym_Pause flags, phylib itself should set those flags,
unless there is a hardware erratum or other special case.  During
autonegotiation, the PHYs will determine whether to enable pause
frame support.

Pause frames are a feature that is supported by the MAC.  It is the MAC
that generates the frames and that processes them.  The PHY can only be
configured to allow them to pass through.

This commit also effectively reverts the recently applied c7a61319
("net: phy: dp83848: Support ethernet pause frames").

So the new process is:

1) Unless the PHY driver overrides it, phylib sets the SUPPORTED_Pause
and SUPPORTED_AsymPause bits in phydev->supported.  This indicates that
the PHY supports pause frames.

2) The MAC driver checks phydev->supported before it calls phy_start().
If (SUPPORTED_Pause | SUPPORTED_AsymPause) is set, then the MAC driver
sets those bits in phydev->advertising, if it wants to enable pause
frame support.

3) When the link state changes, the MAC driver checks phydev->pause and
phydev->asym_pause,  If the bits are set, then it enables the corresponding
features in the MAC.  The algorithm is:

	if (phydev->pause)
		The MAC should be programmed to receive and honor
                pause frames it receives, i.e. enable receive flow control.

	if (phydev->pause != phydev->asym_pause)
		The MAC should be programmed to transmit pause
		frames when needed, i.e. enable transmit flow control.
Signed-off-by: NTimur Tabi <timur@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      529ed127
    • L
      net: ethernet: stmmac: remove private tx queue lock · 739c8e14
      由 Lino Sanfilippo 提交于 
      The driver uses a private lock for synchronization of the xmit function and
the xmit completion handler, but since the NETIF_F_LLTX flag is not set,
the xmit function is also called with the xmit_lock held.

On the other hand the completion handler uses the reverse locking order by
first taking the private lock and (in case that the tx queue had been
stopped) then the xmit_lock.

Improve the locking by removing the private lock and using only the
xmit_lock for synchronization instead.
Signed-off-by: NLino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      739c8e14
    • L
      net: ethernet: sxgbe: remove private tx queue lock · 980f1404
      由 Lino Sanfilippo 提交于 
      The driver uses a private lock for synchronization of the xmit function and
the xmit completion handler, but since the NETIF_F_LLTX flag is not set,
the xmit function is also called with the xmit_lock held.

On the other hand the completion handler uses the reverse locking order by
first taking the private lock and (in case that the tx queue had been
stopped) then the xmit_lock.

Improve the locking by removing the private lock and using only the
xmit_lock for synchronization instead.
Signed-off-by: NLino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      980f1404