Add function f2fs_tmpfile() to support O_TMPFILE file creation, and modify logic
of init_inode_metadata to enable linkat temp file.
Signed-off-by: NChao Yu <chao2.yu@samsung.com>
Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>

After we call find_data_page in truncate_partial_data_page, we could not
guarantee this page is updated or not as error may occurred in lower layer.

We'd better check status of the page to avoid this no updated page be
writebacked to device.
Signed-off-by: NChao Yu <chao2.yu@samsung.com>
Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>

We have already set page update in ->write_begin, so we should remove redundant
SetPageUptodate in ->write_end.
Signed-off-by: NChao Yu <chao2.yu@samsung.com>
Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>

Pull f2fs bugfixes from Jaegeuk Kim:
 "This includes a couple of bug fixes found by xfstests.  In addition,
  one critical bug was reported by Brian Chadwick, which is falling into
  the infinite loop in balance_dirty_pages.  And it turned out due to
  the IO merging policy in f2fs, which was newly merged in 3.16.

   - fix normal and recovery path for fallocated regions
   - fix error case mishandling
   - recover renamed fsync inodes correctly
   - fix to get out of infinite loops in balance_dirty_pages
   - fix kernel NULL pointer error"

* tag 'f2fs-fixes-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs:
  f2fs: avoid to access NULL pointer in issue_flush_thread
  f2fs: check bdi->dirty_exceeded when trying to skip data writes
  f2fs: do checkpoint for the renamed inode
  f2fs: release new entry page correctly in error path of f2fs_rename
  f2fs: fix error path in init_inode_metadata
  f2fs: check lower bound nid value in check_nid_range
  f2fs: remove unused variables in f2fs_sm_info
  f2fs: fix not to allocate unnecessary blocks during fallocate
  f2fs: recover fallocated data and its i_size together
  f2fs: fix to report newly allocate region as extent

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=75861

Denis 2014-05-10 11:28:59 UTC reported:
"F2FS-fs (mmcblk0p28): mounting..
 Unable to handle kernel NULL pointer dereference at virtual address 00000018
 ...
 [<c0a2f678>] (_raw_spin_lock+0x3c/0x70) from [<c03a0330>] (issue_flush_thread+0x50/0x17c)
 [<c03a0330>] (issue_flush_thread+0x50/0x17c) from [<c01b4064>] (kthread+0x98/0xa4)
 [<c01b4064>] (kthread+0x98/0xa4) from [<c0108060>] (kernel_thread_exit+0x0/0x8)"

This patch assign cmd_control_info in sm_info before issue_flush_thread is being
created, so this make sure that issue flush thread will have no chance to access
invalid info in fcc.
Signed-off-by: NChao Yu <chao2.yu@samsung.com>
Reviewed-by: NGu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>

If we don't check the current backing device status, balance_dirty_pages can
fall into infinite pausing routine.

This can be occurred when a lot of directories make a small number of dirty
dentry pages including files.
Reported-by: NBrian Chadwick <brianchad@westnet.com.au>
Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>

If an inode is renamed, it should be registered as file_lost_pino to conduct
checkpoint at f2fs_sync_file.
Otherwise, the inode cannot be recovered due to no dent_mark in the following
scenario.

Note that, this scenario is from xfstests/322.

1. create "a"
2. fsync "a"
3. rename "a" to "b"
4. fsync "b"
5. Sudden power-cut

After recovery is done, "b" should be seen.
However, the result shows "a", since the recovery procedure does not enter
recover_dentry due to no dent_mark.

The reason is like below.
- The nid of "a" is checkpointed during #2, f2fs_sync_file.
- The inode page for "b" produced by #3 is written without dent_mark by
sync_node_pages.

So, this patch fixes this bug by assinging file_lost_pino to the "a"'s inode.
If the pino is lost, f2fs_sync_file conducts checkpoint, and then recovers
the latest pino and its dentry information for further recovery.
Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>

This patch correct releasing code of new_page to avoid BUG_ON in error patch of
f2fs_rename.
Signed-off-by: NChao Yu <chao2.yu@samsung.com>
Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>

If we fail in this path:
->init_inode_metadata
  ->make_empty_dir
    ->get_new_data_page
      ->grab_cache_page return -ENOMEM

We will bug on in error path of init_inode_metadata when call remove_inode_page
because i_block = 2 (one inode block will be released later & one dentry block).

We should release the dentry block in init_inode_metadata to avoid this BUG_ON,
and avoid leak of dentry block resource, because we never have second chance to
release that block in ->evict_inode as in upper error path we make this inode
'bad'.
Signed-off-by: NChao Yu <chao2.yu@samsung.com>
Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>

This patch add lower bound verification for nid in check_nid_range, so nids
reserved like 0, node, meta passed by caller could be checked there.

And then check_nid_range could be used in f2fs_nfs_get_inode for simplifying
code.
Signed-off-by: NChao Yu <chao2.yu@samsung.com>
Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>

Remove unused variables in struct f2fs_sm_info.
Signed-off-by: NChao Yu <chao2.yu@samsung.com>
Signed-off-by: NJaegeuk Kim <jaegeuk@kernel.org>

Pull hwmon fixes from Guenter Roeck:
 "Fix a number of zero-day bugs, mostly found with module test scripts.
  Nothing major, but potentially annoying and worthwhile to fix"

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (adc128d818) Drop write support on inX_input attributes
  hwmon: (emc2103) Clamp limits instead of bailing out
  hwmon: (adm1031) Fix writes to limit registers
  hwmon: (adm1021) Fix cache problem when writing temperature limits
  hwmon: (adm1029) Ensure the fan_div cache is updated in set_fan_div
  hwmon: (amc6821) Fix permissions for temp2_input
  hwmon: (ntc_thermistor) Correct information printed during probe

Pull thermal fixes from Zhang Rui:
 "Specifics:

   - update Email address of Thermal subsystem maintainer Eduardo
     Valentin.

   - fix a problem that unloading thermal module results in kernel crash
     because a non-exist device file is removed on thermal unload.

   - fix a problem that critical trip point is set wrongly on latest
     i.MX6 SOC and results in system critical shutdown.

   - a couple of fixes to Tmon tool, of-thermal code and ti thermal
     driver"

* 'for-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
  tmon: set umask to a reasonable value
  tmon: Check log file for common secuirty issues
  tools/thermal: tmon: fix compilation errors when building statically
  thermal: ti-soc-thermal: ti-bandgap.c: Cleaning up wrong address is checked
  Thermal: imx: correct critical trip temperature setting
  thermal: Bind cooling devices with the correct arguments
  thermal: Add braces around suspect code
  thermal: hwmon: Make the check for critical temp valid consistent
  MAINTAINERS: Update Eduardo Valentin's email address

Pull HID fixes from Jiri Kosina:
 "A few tiny HID subsystem fixes for 3.16"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: use multi input quirk for 22b9:2968
  HID: sensor-hub: fix potential memory leak
  HID: usbhid: quirk for PM1610 and PM1640 Touchscreen.
  HID: rmi: Protect PM-only functions by #ifdef CONFIG_PM
  HID: sensor-hub: introduce Kconfig dependency on IOMEM
  HID: sensor-hub: make dyn_callback_lock IRQ-safe

Pull pin control fixes from Linus Walleij:
 "Two fixes for the pin control subsystem, both relating to the error
  path in probe()

  I'm a bit snowed under by mail but these have boiled in linux-next and
  should propagate to you"

* tag 'pinctrl-v3.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: berlin: fix an error code in berlin_pinctrl_probe()
  pinctrl: sunxi: Fix potential null pointer dereference

Writes into input registers doesn't make sense, even more so since
the writes actually ended up writing into the maximum limit registers.
Drop it.

Cc: stable@vger.kernel.org
Reviewed-by: NJean Delvare <jdelvare@suse.de>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

It is customary to clamp limits instead of bailing out with an error
if a configured limit is out of the range supported by the driver.
This simplifies limit configuration, since the user will not typically
know chip and/or driver specific limits.
Reviewed-by: NJean Delvare <jdelvare@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

This device generates ABS_Z and ABS_RX events instead of ABS_X and
ABS_Y.
Signed-off-by: NWen-chien Jesse Sung <jesse.sung@canonical.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Upper limit for write operations to temperature limit registers
was clamped to a fractional value. However, limit registers do
not support fractional values. As a result, upper limits of 127.5
degrees C or higher resulted in a rounded limit of 128 degrees C.
Since limit registers are signed, this was stored as -128 degrees C.
Clamp limits to (-55, +127) degrees C to solve the problem.

Value on writes to auto_temp[12]_min and auto_temp[12]_max were not
clamped at all, but masked. As a result, out-of-range writes resulted
in a more or less arbitrary limit. Clamp those attributes to (0, 127)
degrees C for more predictable results.

Cc: Axel Lin <axel.lin@ingics.com>
Cc: stable@vger.kernel.org
Reviewed-by: NJean Delvare <jdelvare@suse.de>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

Pull devicetree bugfix from Grant Likely:
 "Important bug fix for parsing 64-bit addresses on 32-bit platforms.
  Without this patch the kernel will try to use memory ranges that
  cannot be reached"

* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux:
  of: Check for phys_addr_t overflows in early_init_dt_add_memory_arch

Pull SCSI fixes from James Bottomley:
 "This is a set of 13 fixes, a MAINTAINERS update and a sparse update.
  The fixes are mostly correct value initialisations, avoiding NULL
  derefs and some uninitialised pointer avoidance.

  All the patches have been incubated in -next for a few days.  The
  final patch (use the scsi data buffer length to extract transfer size)
  has been rebased to add a cc to stable, but only the commit message
  has changed"

* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  [SCSI] use the scsi data buffer length to extract transfer size
  virtio-scsi: fix various bad behavior on aborted requests
  virtio-scsi: avoid cancelling uninitialized work items
  ibmvscsi: Add memory barriers for send / receive
  ibmvscsi: Abort init sequence during error recovery
  qla2xxx: Fix sparse warning in qla_target.c.
  bnx2fc: Improve stats update mechanism
  bnx2fc: do not scan uninitialized lists in case of error.
  fc: ensure scan_work isn't active when freeing fc_rport
  pm8001: Fix potential null pointer dereference and memory leak.
  MAINTAINERS: Update LSILOGIC MPT FUSION DRIVERS (FC/SAS/SPI) maintainers Email IDs
  be2iscsi: remove potential junk pointer free
  be2iscsi: add an missing goto in error path
  scsi_error: set DID_TIME_OUT correctly
  scsi_error: fix invalid setting of host byte

Pull drm fixes from Dave Airlie:
 "i915, tda998x and vmwgfx fixes,

  The main one is i915 fix for missing VGA connectors, along with some
  fixes for the tda998x from Russell fixing some modesetting problems.

  (still on holidays, but got a spare moment to find these)"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/vmwgfx: Fix incorrect write to read-only register v2:
  drm/i915: Drop early VLV WA to fix Voltage not getting dropped to Vmin
  drm/i915: only apply crt_present check on VLV
  drm/i915: Wait for vblank after enabling the primary plane on BDW
  drm/i2c: tda998x: add some basic mode validation
  drm/i2c: tda998x: faster polling for edid
  drm/i2c: tda998x: move drm_i2c_encoder_destroy call

Pull ARM SoC fixes from Olof Johansson:
 "This week's arm-soc fixes:

   - A set of of OMAP patches that we had missed Tony's pull request of:
     * Reset fix for am43xx
     * Proper OPP table for omap5
     * Fix for SoC detection of one of the DRA7 SoCs
     * hwmod updates to get SATA and OCP to work on omap5 (drivers
       merged in 3.16)
     * ... plus a handful of smaller fixes
   - sunxi needed to re-add machine specific restart code that was
     removed in anticipation of a watchdog driver being merged for 3.16,
     and it didn't make it in.
   - Marvell fixes for PCIe on SMP and a big-endian fix.
   - A trivial defconfig update to make my capri test board boot with
     bcm_defconfig again.

  ... and a couple of MAINTAINERS updates, one to claim new Keystone
  drivers that have been merged, and one to merge MXS and i.MX (both
  Freescale platforms).

  The largest diffs come from the hwmod code for omap5 and the re-add of
  the restart code on sunxi.  The hwmod stuff is quite late at this
  point but it slipped through cracks repeatedly while coming up the
  maintainer chain and only affects the one SoC so risk is low"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  MAINTAINERS: Add few more Keystone drivers
  MAINTAINERS: merge MXS entry into IMX one
  ARM: sunxi: Reintroduce the restart code for A10/A20 SoCs
  ARM: mvebu: fix cpuidle implementation to work on big-endian systems
  ARM: mvebu: update L2/PCIe deadlock workaround after L2CC cleanup
  ARM: mvebu: move Armada 375 external abort logic as a quirk
  ARM: bcm: Fix bcm and multi_v7 defconfigs
  ARM: dts: dra7-evm: remove interrupt binding
  ARM: OMAP2+: Fix parser-bug in platform muxing code
  ARM: DTS: dra7/dra7xx-clocks: ATL related changes
  ARM: OMAP2+: drop unused function
  ARM: dts: am43x-epos-evm: Add Missing cpsw-phy-sel for am43x-epos-evm
  ARM: dts: omap5: Update CPU OPP table as per final production Manual
  ARM: DRA722: add detection of SoC information
  ARM: dts: Enable twl4030 off-idle configuration for selected omaps
  ARM: OMAP5: hwmod: Add ocp2scp3 and sata hwmods
  ARM: OMAP2+: hwmod: Change hardreset soc_ops for AM43XX

Pull irq fixes from Thomas Gleixner:
 "A few minor fixlets in ARM SoC irq drivers and a fix for a memory leak
  which I introduced in the last round of cleanups :("

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq: Fix memory leak when calling irq_free_hwirqs()
  irqchip: spear_shirq: Fix interrupt offset
  irqchip: brcmstb-l2: Level-2 interrupts are edge sensitive
  irqchip: armada-370-xp: Mask all interrupts during initialization.

Fixes for 3.16-rc3; most importantly Jesse brings back VGA he took away
on a bunch of machines. Also a vblank fix for BDW and a power workaround
fix for VLV.

* tag 'drm-intel-fixes-2014-07-03' of git://anongit.freedesktop.org/drm-intel:
  drm/i915: Drop early VLV WA to fix Voltage not getting dropped to Vmin
  drm/i915: only apply crt_present check on VLV
  drm/i915: Wait for vblank after enabling the primary plane on BDW

fix to a 3.15 commit.

* 'vmwgfx-fixes-3.16' of git://people.freedesktop.org/~thomash/linux:
  drm/vmwgfx: Fix incorrect write to read-only register v2:

mode fixes for tda998x.

* 'tda998x-fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-cubox:
  drm/i2c: tda998x: add some basic mode validation
  drm/i2c: tda998x: faster polling for edid
  drm/i2c: tda998x: move drm_i2c_encoder_destroy call

irq_free_hwirqs() always calls irq_free_descs() with a cnt == 0
which makes it a no-op since the interrupt count to free is
decremented in itself.

Fixes: 7b6ef126Signed-off-by: NKeith Busch <keith.busch@intel.com>
Acked-by: NDavid Rientjes <rientjes@google.com>
Link: http://lkml.kernel.org/r/1404167084-8070-1-git-send-email-keith.busch@intel.comSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

Pull ARM64 fixes from Catalin Marinas:
 - Exception level check at boot time (for completeness, not triggering
   any bug before)
 - I/D-cache synchronisation logic for huge pages
 - Config symbol typo

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: fix el2_setup check of CurrentEL
  arm64: mm: Make icache synchronisation logic huge page aware
  arm64: mm: Fix horrendous config typo

Update MAINTAINERS file for recently added reset controller, AEMIF
and clocksource driver for Keystone SOCs.

The EMIF memory controller driver is also added along with AEMIF.

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The mach-mxs platform is actually co-maintained by myself and
pengutronix folks.  Also it's hosted in the same kernel tree as IMX.
So let's merge the entry into IMX one.
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NOlof Johansson <olof@lixom.net>

mvebu fixes for v3.16 (round #2)

 - mvebu
    - Fix PCIe deadlock now that SMP is enabled
    - Fix cpuidle for big-endian systems

* tag 'mvebu-fixes-3.16-2' of git://git.infradead.org/linux-mvebu:
  ARM: mvebu: fix cpuidle implementation to work on big-endian systems
  ARM: mvebu: update L2/PCIe deadlock workaround after L2CC cleanup
  ARM: mvebu: move Armada 375 external abort logic as a quirk
Signed-off-by: NOlof Johansson <olof@lixom.net>

This partly reverts commits 55360050 (ARM: sunxi: Remove reset code from
the platform) and 5e669ec5 (ARM: sunxi: Remove init_machine callback) for
the sun4i, sun5i and sun7i families.

This is needed because the watchdog counterpart of these commits was dropped,
and didn't make it into 3.16. In order to still be able to reboot the board, we
need to reintroduce that code. Of course, the long term view is still to get
rid of that code in mach-sunxi.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'omap-for-v3.16/fixes-against-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Merge OMAP fixes from Tony Lindgren:

Fixes for omaps for issues discovered during the merge window and
enabling of a few features that had to wait for the driver
dependencies to clear.

The fixes included are:

- Fix am43xx hard reset flags
- Fix SoC detection for DRA722
- Fix CPU OPP table for omap5
- Fix legacy mux parser bug if requested muxname is a prefix of
  multiple mux entries
- Fix qspi interrupt binding that relies on the irq crossbar
  that has not yet been enabled
- Add missing phy_sel for am43x-epos-evm
- Drop unused gic_init_irq() that is no longer needed

And the enabling of features that had driver dependencies are:

- Change dra7 to use Audio Tracking Logic clock instead of a fixed
  clock now that the clock driver for it has been merged

- Enable off idle configuration for selected omaps as all the kernel
  dependencies for device tree based booting are finally merged as
  this is needed to get the automated PM tests working finally with
  device tree based booting

- Add hwmod entry for ocp2scp3 for omap5 to get sata working as
  all the driver dependencies are now in the kernel and this patch
  fell through the cracks during the merge window

* tag 'omap-for-v3.16/fixes-against-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: dra7-evm: remove interrupt binding
  ARM: OMAP2+: Fix parser-bug in platform muxing code
  ARM: DTS: dra7/dra7xx-clocks: ATL related changes
  ARM: OMAP2+: drop unused function
  ARM: dts: am43x-epos-evm: Add Missing cpsw-phy-sel for am43x-epos-evm
  ARM: dts: omap5: Update CPU OPP table as per final production Manual
  ARM: DRA722: add detection of SoC information
  ARM: dts: Enable twl4030 off-idle configuration for selected omaps
  ARM: OMAP5: hwmod: Add ocp2scp3 and sata hwmods
  ARM: OMAP2+: hwmod: Change hardreset soc_ops for AM43XX

We are returning success here because PTR_ERR(NULL) is zero.  We should
be returning -ENODEV.

Fixes: 3de68d33 ('pinctrl: berlin: add the core pinctrl driver for Marvell Berlin SoCs')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Pull md bugfixes from Neil Brown:
 "Two minor bugfixes for md in 3.16"

* tag 'md/3.16-fixes' of git://neil.brown.name/md:
  md: flush writes before starting a recovery.
  md: make sure GET_ARRAY_INFO ioctl reports correct "clean" status

Pull sound fixes from Takashi Iwai:
 "This contains a few fixes for HD-audio: yet another Dell headset pin
  quirk, a fixup for Thinkpad T540P, and an improved fix for
  Haswell/Broadwell HDMI clock setup"

* tag 'sound-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda - restore BCLK M/N value as per CDCLK for HSW/BDW display HDA controller
  drm/i915: provide interface for audio driver to query cdclk
  ALSA: hda - Add a fixup for Thinkpad T540p
  ALSA: hda - Add another headset pin quirk for some Dell machines

Pull btrfs fixes from Chris Mason:
 "We've queued up a few fixes in my for-linus branch"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: fix crash when starting transaction
  Btrfs: fix btrfs_print_leaf for skinny metadata
  Btrfs: fix race of using total_bytes_pinned
  btrfs: use E2BIG instead of EIO if compression does not help
  btrfs: remove stale comment from btrfs_flush_all_pending_stuffs
  Btrfs: fix use-after-free when cloning a trailing file hole
  btrfs: fix null pointer dereference in btrfs_show_devname when name is null
  btrfs: fix null pointer dereference in clone_fs_devices when name is null
  btrfs: fix nossd and ssd_spread mount option regression
  Btrfs: fix race between balance recovery and root deletion
  Btrfs: atomically set inode->i_flags in btrfs_update_iflags
  btrfs: only unlock block in verify_parent_transid if we locked it
  Btrfs: assert send doesn't attempt to start transactions
  btrfs compression: reuse recently used workspace
  Btrfs: fix crash when mounting raid5 btrfs with missing disks
  btrfs: create sprout should rename fsid on the sysfs as well
  btrfs: dev replace should replace the sysfs entry
  btrfs: dev add should add its sysfs entry
  btrfs: dev delete should remove sysfs entry
  btrfs: rename add_device_membership to btrfs_kobj_add_device

The CurrentEL system register reports the Current Exception Level
of the CPU. It doesn't say anything about the stack handling, and
yet we compare it to PSR_MODE_EL2t and PSR_MODE_EL2h.

It works by chance because PSR_MODE_EL2t happens to match the right
bits, but that's otherwise a very bad idea. Just check for the EL
value instead.
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
[catalin.marinas@arm.com: fixed arch/arm64/kernel/efi-entry.S]
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>