When support for 82577/82578 was added[1] in 2.6.31, PHY wakeup was in-
advertently enabled (even though it does not function properly) on ICH10
LOMs.  This patch makes it so that the ICH10 LOMs use MAC wakeup instead
as was done with the initial support for those devices (i.e. 82567LM-3,
82567LF-3 and 82567V-4).

[1] commit a4f58f54Reported-by: NAurelien Jarno <aurelien@aurel32.net>
Cc: <stable@kernel.org>
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Reported-by: NStephen Hemminger <shemminger@vyatta.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Sparse complains because the e1000 driver is calling ioread on a pointer
not tagged as __iomem.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Reviewed-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This is similar to what we already do in cdc-phonet.c in the same
situation. pskb_pull() refuses to work with HIGHMEM, even if it is
known that the socket buffer is entirely in "low" memory.
Signed-off-by: NRémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The platform_device_id table is supposed to be zero-terminated.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

platform_set_drvdata() was used with argument of incorrect type and
could cause memory corruption. Moreover, because of not setting drvdata
in the correct place not all resources were freed upon module unload.
Signed-off-by: NIlya Yanok <yanok@emcraft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 71d64290 (Driver core: convert platform_{get,set}_drvdata to
static inline functions) now triggers a warning in the macb network
driver:

  CC      drivers/net/macb.o
drivers/net/macb.c: In function ‘macb_mii_init’:
drivers/net/macb.c:263: warning: passing argument 1 of ‘platform_set_drvdata’ from incompatible pointer type
include/linux/platform_device.h:138: note: expected ‘struct platform_device *’ but argument is of type ‘struct net_device *’

Use dev_set_drvdata() on the device embedded in the net_device instead.

Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I just found that the controller hardware name is not set for the Softing
driver. After this patch, "$ ip -d link show" looks nicer.
Signed-off-by: NKurt Van Dijck <kurt.van.dijck@eia.be>
Acked-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The below patch changes a typo "pice" to "piece"
Signed-off-by: NJustin P. Mattock <justinmattock@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fmvj18x_cs:add new id
           Toshiba lan&modem multifuction card (model name:IPC5010A)
Signed-off-by: NKen Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The API for network devices has changed so that setting carrier off at
probe is no longer required.  This should fix the IPv6 addrconf issue.

Addresses https://bugzilla.kernel.org/show_bug.cgi?id=29612Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Reported-by: NGeorge Billios <gbillios@gmail.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The device is very similar to (0x0fe6, 0x8101),
And works well with dm9601 driver.
Signed-off-by: NShahar Havivi <shaharh@redhat.com>
Acked-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- fix the RTL8111DP turn off the power when DASH is enabled.
- RTL_GIGA_MAC_VER_27 must wait for tx finish before reset.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Acked-by: NFrancois Romieu <romieu@fr.zoreil.com>

Adjust and remove certain settings of RTL8102E which are for previous chips.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Acked-off-by: NFrancois Romieu <romieu@fr.zoreil.com>

It results in the wrong point address and influences RTL8168DP.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Acked-by: NFrancois Romieu <romieu@fr.zoreil.com>

DM9000 revision B needs 1 ms delay after PHY power-on.
PHY must be powered on by writing 0 into register DM9000_GPR before
all other settings will change (see Davicom spec and example code).

Remember, that register DM9000_GPR was not changed by reset sequence.

Without this fix the FIFO is out of sync and sends wrong data after
sequence of "ifconfig ethX down ; ifconfig ethX up".
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The spin_lock should hold before reading register.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/sfc/ethtool.c: In function ‘efx_ethtool_self_test’:
drivers/net/sfc/ethtool.c:613: warning: the frame size of 1200 bytes
is larger than 1024 bytes
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Acked-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Documentation/DMA-API-HOWTO.txt states:

"DMA transfers need to be synced properly in order for
the cpu and device to see the most uptodate and correct
copy of the DMA buffer."

Cc: <stable@kernel.org>
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As reported and found by Johannes Stezenbach:
rt2800{pci,usb} do not report the Michael MIC in RXed frames, but do check
the Michael MIC in hardware. Therefore we have to report to mac80211 that the
received frame does not include the Michael MIC.

https://bugzilla.kernel.org/show_bug.cgi?id=16608Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fast channel change fixes:

a) Always set OFDM timings
b) Don't re-activate PHY
c) Enable only NF calibration, not AGC

https://bugzilla.kernel.org/show_bug.cgi?id=27382Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Correct channel setting function must be used for AR2317.
When I tested ahb patch on bullet2 all seemed to work fine,
but it couldn't connect another host (using ibss for example).
During an analysis I observed that it's transmitting on another
channel. I looked into madwifi code and understood that
the problem is in channel setting function. So atheros RF2317 not
fully handled in the current ath5k version and must be patched.
Signed-off-by: NNikolay Ledovskikh <nledovskikh@gmail.com>
Acked-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

taken two RT35XX EDIMAX from DPO_RT3562_3592_3062_LinuxSTA_V2.4.1.1_20101217
Signed-off-by: NXose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch re-enables UIE timer/polling emulation for rtc devices
that do not support alarm irqs.

CC: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
CC: Thomas Gleixner <tglx@linutronix.de>
Reported-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>

Uwe pointed out that my alarm based UIE emulation is not sufficient
to replace the older timer/polling based UIE emulation on devices
where there is no alarm irq. This causes rtc devices without alarms
to return -EINVAL to UIE ioctls. The fix is to re-instate the old
timer/polling method for devices without alarm irqs.

This patch reverts the following commits:
042620a0 - Remove UIE emulation
1daeddd5 - Cleanup removed UIE emulation declaration
b5cc8ca1 - Remove Kconfig symbol for UIE emulation

The emulation mode will still need to be wired-in with a following
patch before it will work.

CC: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
CC: Thomas Gleixner <tglx@linutronix.de>
Reported-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>

On hardware that doesn't support alarm interrupts, rtc_alarm_irq_enable
could return without releasing the ops_lock mutex.

This was introduced in
	aa0be0f4 (RTC: Propagate error handling via rtc_timer_enqueue properly)

This patch corrects the issue by only returning once the mutex is
released.

[john.stultz: Reworded the commit log]
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>

If management firmware is present and the device is down, the firmware
will assume control of the phy.  If a phy access were allowed from the
host, it will collide with firmware phy accesses, resulting in
unpredictable behavior.  This patch fixes the problem by disallowing phy
accesses during the problematic condition.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Without calling of netif_carrier_off at the end of the probe the operstate
is unknown when the device is initially opened. By default the carrier is
on so when the device is opened and netif_carrier_on is called the link
watch event is not fired and operstate remains zero (unknown).

This patch fixes this behavior in forcedeth and r8169.
Signed-off-by: NIvan Vecera <ivecera@redhat.com>
Acked-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a double completion associated with error handling for RC QPs.

The sequence is:

 - The do_rc_ack() routine fields an RNR nack and there are 0
   rnr_retries configured on the QP.
 - qib_error_qp() stops the pending timer
 - qib_rc_send_complete() is called from sdma_complete()
 - qib_rc_send_complete() starts the timer because the msb of the psn
   just completed says an ack is needed.
 - a bunch of flushes occur as ipoib posts WQEs to an error'ed QP
 - rc_timeout() calls qib_restart_rc()
 - qib_restart_rc() calls qib_send_complete() with a
   IB_WC_RETRY_EXC_ERR on a wqe that has already been completed in the
   past

The fix avoids starting the timer since another packet will never
arrive.
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Otherwise we fail to properly suspend/resume all of the emulated devices.

Something between 2.6.38-rc2 and rc3 appears to have exposed this
issue, but it's always been wrong not to do this.
Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Acked-by: NStefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: NJeremy Fitzhardinge <jeremy@goop.org>

A HW limitation was recently discovered where the last buffer in a DDP offload
cannot be a full buffer size in length. Fix the issue with a work around by
adding another buffer with size = 1.
Signed-off-by: NAmir Hanania <amir.hanania@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Systems containing an 82599EB and running a backported driver from
upstream were panicing on boot.  It turns out hw->mac.ops.setup_sfp is
only set for 82599, so one should check to be sure that pointer is set
before continuing in ixgbe_sfp_config_module_task.  I verified by
inspection that the upstream driver has the same issue and also added a
check before the call in ixgbe_sfp_link_config.
Signed-off-by: NAndy Gospodarek <andy@greyhouse.net>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver was not flushing all writebacks before unloading, possibly
causing memory to be written by the hardware after the driver had
reinitialized the rings.

This adds missing functionality to flush any pending writebacks and is
called in all spots where descriptors should be completed before the driver
begins processing.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is part of a fix to avoid any tasks running while the driver is
exiting and deinitializing resources.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The fixed ref/post dividers are set by the AdjustPll table
rather than the ss info table on dce4+.  Make sure we enable
the fractional feedback dividers when using a fixed post
or ref divider on them as well.

Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=29272Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NMarek Olšák <maraeo@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This has been broken since 2.6.37, and fixes resume on a couple of fermi
boards I have access to.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

We free the temporary binding before leaving this function, so we also have
to wait for the move to actually complete.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Due to the default case handling the older chipsets, a bunch of the newer
ones ended up having the wrong tiling regs used.  This commit switches the
default case to handle the newest chipsets.

This also makes nv4e touch the "extra" tiling regs.  "nv" doesn't touch
them for C51 but traces of the NVIDIA binary driver show it being done
there.

I couldn't find NV41/NV45 traces to confirm the behaviour there, but an
educated guess was taken at each of them.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>