Continue the clearout of plat-s3c by moving audio-simtec.h to plat-s3c24xx
as there are no current implementations outside of this platform.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Move the Kconfig entries from plat-s3c to plat-samsung and plat-s3c24xx
as necessary. The S3C_BOOT entries and the DMA configuration can go to
plat-samsung. The low-level UART configurations are currently S3C2XX
specific and can go to plat-s3c24xx.

Eliminating plat-s3c from the build process will be submitted seperately.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Move the init.c and time.c files to plat-samsung from plat-s3c, thus
clearing the last files that are being built in here.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Move the core of the DMA support to plat-samsung for everyone to use.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Move pm.c to plat-samsung, it should be usable by all Samsung systems
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Move the map-base file to plat-samsung. To make the move easier, we do not
change the S3C_ prefix on many of the items as this would involve going
through altering all the dependencies.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Move common headers from plat-s3c's include/plat directory into plat-samsung.

No need to fix any files, these are still included via <plat/>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Merge branch 'next-samsung-s3c64xx-platdeletion' into next-samsung

Conflicts:

	arch/arm/mach-s3c64xx/Makefile (fixed)

Now we've move the support out of plat-s3c64xx for everything, eliminate
the platform directory arch/arm/plat-s3c64xx and remove it from the ARM
build configuration.

Note, PLAT_S3C64XX is kept around for the moment until the drivers that
depend on it can be updated, so it is moved to the mach-s3c64xx Kconfig.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

dma-plat.h is the last file left in plat-s3c64xx, but to remove it we
must also change the use of dma-plat.h by the core code and the s3c24xx
implementation.

Rename the s3c24xx dma-plat.h in the common plat-samsung directory as it
may be used for other ports. Move the specific dma bits into the
mach-s3c64xx directory and update the build as needed.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Move the pm-core.h to the machine include directory in the process of
eliminating the plat-s3c64xx.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Remove the Kconfig and PLAT_S3C64XX defines for the previous S3C64XX
directory structure now that the code is moved into mach-s3c64xx.

Note, we cannot currently remove plat-s3c64xx directory as we have a
pair of include files used within plat-s3c and plat-samsung that need
to find a new home.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Turn the init sequence of
	s3c24xx_register_baseclocks(xtal);
	s3c64xx_register_clocks();
	s3c6400_register_clocks(S3C6410_CLKDIV0_ARM_MASK);

into a single call as this is now contained within one file.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Merge plat-s3c64xx/s3c6400-clock.c mach-s3c64xx/clock.c placing all the
clock code into one place.

Note, no effort is made in this patch to squash the init functions
together.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Since this file is small, and is compiled for both systems in this
architecture merge it into the cpu support file and remove the original
instead of moving it.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Move the core S3C64XX support to mach-s3c64xx as it is unlikely to be used
outside of this directory. Also move the SoC header files in with it.

This includes the clock, cpu, cpufreq, dma, gpiolib and pll support.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Move the S3C64XX specific device and setup files into mach-s3c64xx as
they are unlikely to be used outside of this code.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Move IRQ support to mach-s3c64xx as it is unlikely to be re-used outside
this machine.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Move the register and GPIO definition files from plat-s3c64xx into the
machine include direcotry as they are unlikely to be reused outside
mach-s3c64xx.

This move includes removing the empty <mach/regs-clock.h> and replacing
it with the <plat/regs-clock.h> implementation.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Merge branch 'next-samsung-s3c244x-merge' into next-samsung

Merge branch 'next-samsung-devupdates2' into next-samsung

The S3C64XX SoC series support 12bit ADC data, enable this and
mask the data accordingly.
Signed-off-by: NMaurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Making the code depend on CONFIG_SND_S3C24XX_SOC means that if the ASoC
code is build modularily, the boards will fail to link due to the device
code also being built as a module.

As per Mark Brown's suggestions, just compile this always as it is expected
many machines will have audio.

Also move the obj-y line out of the device setup area into a new area just
for devices.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

As part of the development process, it is hoped PLAT_S3C is either removed
from all of the PLAT_SAMSUNG derived platforms or removed entirely. It is
also better to use PLAT_SAMSUNG as this is the current base of all Samsung
devices.

Change the two places that use PLAT_S3C to use PLAT_SAMSUNG
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add SERIAL_SAMSUNG_UARTS_4 to mop up the number of cases currently using
four Samsung compatible UARTS.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The S3C2412 has a fractional baud rate register, this patch adds the
corresponding flag to the UART definition to allow generation of more
precise baud rates for the various clock combinations.
Signed-off-by: NMichel Pollet <buserror@gmail.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The SPI controller platform devices should be compiled in
independent of the driver support, otherwise we might end
up with dev-spi built as kernel module.
Change this to make every machine select if it has some SPI
device and wants to build device definitions.
Signed-off-by: NJassi Brar <jassi.brar@samsung.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add the required DMA masks to the hs-otg device definition to allow DMA
to work with it.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Merge these two headers into one, these two SoCs are so similar.

Note, correct fault in mach-smdk2443.h including the wrong header.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Remove the old common S3C2440 and S3C2442 SoC support from plat-s3c24xx
into mach-s3c2440 now this directory is serving both SoCs.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Remove the old mach-s3c2442 directory now all is merged into mach-s3c2440
and remove it from the arch/arm build process.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Move the remaining S3C2442 code into mach-s3c2440 as there is only one
file currently in there and these two SoCs are very similar.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Fix the entries for SMDK2440 should have allowed for S3C2440 or S3C2440
SoC selection but this depended on ARCH_S3C2440 which has not been around
for a while.

Remove the dependency to allow this to be selected.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Merge s3c2442.c and clock.c as the s3c242.c does not contain much and
the clock parts are always built for s3c2442 anyway.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Move the pair of machines in arch/arm/mach-s3c2442 into the mach-s3c2440
directory as the S3C2440 and S3C2442 are very close.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Currently, S5P_TIMER_IRQ is based at the end of VICs. This patch changes
the S5P_TIMER_IRQ base from end of VICs to 11 in ISA IRQ space.
No of VICs varies between SOCs. This causes an exception on S5P6442.
Signed-off-by: NAtul Dahiya <atul.dahiya@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

1. Moved common memory map definitions for S5P such as S5P_VA_XXX
   into plat-s5p/include/mach/map-s5p.h from mach-s5p6440/include/mach.
2. Removed unnecessary definitions in the map.h and irq.c
3. Removed the unnecessary support for unaligned UART address
4. Renamed S5P_VA_VICx definitions as VA_VICx
5. Moved the definitons of VIC_BASE to plat-s5p/include/plat/irqs.h
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The s5p6440-clock.c and s5p6440-init.c code in the plat-s5p is specific to
s5p6440 SoC based systems. So these files are being moved to the machine
directory of s5p6440. And these files are renamed in the machine directory.
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Merge branch 'next-smdk6410-defconfig' into next-samsung

Add an error print to s3c24xx_register_clocks to provide more useful
information when failing to register the clock.

I belive this was originally left out due to the possibility of a
problem with low-level debugging code. However, if the low-level
debug code is not functional by now there will be a whole other set of
problems being presented to the system.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>