On bf518-ezbrd with DSA Ethernet switch enabled, on chip MAC is
connecting to phy at address 3.  If allowing the netdevice framework to
probe both 3 phys of the switch when registering MAC phy, phy at address
1 is checked for link active status other than phy at address 3.  If
connecting a cable to port 2 and leave port 1 open, link status in phy
2 and 3 are online, while that in phy 1 is offline.  So, the phy layer
sets wrong offline status to net device on port 3.  In this case, no data
can be transferred via ethernet port 2.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The SPORT/UART driver doesn't use the secondary channel pins, so don't
try and request them thus keeping other drivers from using them.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Move all the pin settings out of the Kconfig and into the platform
resources (MII vs RMII).  This clean up also lets us push out the
phy settings so that board porters may control the layout.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

This board has a SSM2603 codec, so make sure we have the right resources
declared for it.
Signed-off-by: NBob Liu <lliubbo@gmail.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The num_chipselect field for on-chip Blackfin SPI buses is supposed to
be 1 larger than the number of actual CSs available.  This is because
the hardware starts counting at 1 and not 0.  There is a field for "CS0",
but it is marked as "reserved" everywhere.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NHarald Krapfenbauer <harald.krapfenbauer@bluetechnix.at>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

This lets people easily select the UART/SPORT consoles for early printk
while leveraging the pins declared in the boards file.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Rather than keeping the pins in the actual driver and worrying about a
mess of Kconfig options, declare all the desired pin resources in the
boards file.  This lets people easily select the specific pins/ports for
the normal emulated UART as well as GPIOs for CTS/RTS.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Rather than keeping the pins in the actual driver and worrying about a
mess of Kconfig options, declare all the desired pin resources in the
boards file.  This lets people easily select the specific pins/ports for
the normal UART as well as GPIOs for CTS/RTS.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The simple-gpio has been replaced by the gpio sysfs interface, so drop the
unused simple-gpio resources from all Blackfin boards.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Bill Gatliff & David Brownell pointed out we were missing some
copyrights, and licensing terms in some of the files in
./arch/blackfin, so this fixes things, and cleans them up.

It also removes:
 - verbose GPL text(refer to the top level ./COPYING file)
 - file names (you are looking at the file)
 - bug url (it's in the ./MAINTAINERS file)
 - "or later" on GPL-2, when we did not have that right

It also allows some Blackfin-specific assembly files to be under a BSD
like license (for people to use them outside of Linux).
Signed-off-by: NRobin Getz <robin.getz@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

These hardware devices are dead and the drivers never cleaned up/merged,
so punt the useless board resource info.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The "TWI_KEYPAD" driver was renamed to "INPUT_PCF8574", so update the
defines in the board resources accordingly.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The sed used to rename the bfin-twi-lcd only replaced the first instance
rather than all which led to the resources not being enabled when the
driver was built as a module.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The common DSA code changed structure layout, so update the BF518F-EZBRD
resources accordingly.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The SPI flash on the BF518F-EZBRD board is actually hooked up to CS2,
not CS1, so make sure the resources are correct.

URL: http://blackfin.uclinux.org/gf/tracker/5220Signed-off-by: NGraf Yang <graf.yang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The Blackfin SPI driver can be driven by an IRQ now, so declare it in
the board resources.
Signed-off-by: NYi Li <yi.li@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Try to keep the naming conventions consistent, so:
	SPI_ADC_BF533 -> BFIN_SPI_ADC
	TWI_LCD       -> BFIN_TWI_LCD
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The two high address lines on the BF51x are not dedicated which means we
need to handle them like any other peripheral pin if we want to access the
upper 2MB of parallel flash.
Signed-off-by: NGraf Yang <graf.yang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Signed-off-by: NGraf Yang <graf.yang@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Blackfin arch: add platform device bfin_mii-bus and KSZ8893M switch driver platform resources to board files
Signed-off-by: NGraf Yang <graf.yang@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Drop CONFIG_I2C_BOARDINFO ifdefs as the common i2c header handles this
already by stubbing things out
Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

[Mike Frysinger <vapier.adi@gmail.com>:
 - setup P_DEFAULT_BOOT_SPI_CS  for every arch based on
   the default bootrom behavior and convert all our boards
   to it
 - revert previous anomaly change ... bf51x is not affected
   by anomaly 05000353]
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Signed-off-by: NCliff Cai <cliff.cai@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Signed-off-by: NGraf Yang <graf.yang@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Cc: Graf Yang <graf.yang@analog.com>
Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Signed-off-by: NBryan Wu <cooloney@kernel.org>