Status register and enable register are identical regarding their
layout. Use the bit definitions for both.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The i2c core has per-adapter locks, so no need to protect again.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The old macros made it harder to see what was actually happening.
Replace them with something more readable.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Setting up a read or write message is similar enough to be done in one
function. Also, move a helper function into the new function since it is
only used here.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

We should always check if the bus is free, independently if it is a read
or write. It should be done before the first message, though. After
that, we ourselves keep the bus busy. Remove a 'ret' assignment which
only silenced a build warning.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Remove the seperate functions and use designated constants. As readable
but less overhead. Actually, this is even more readable since the old
function used a mix of "=" and "|=".
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Remove the seperate functions and use designated constants. As readable
but less overhead.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

We use devm, so irq number is only needed during probe.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Very basic operations, just called once, can also go to the caller.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Signed-off-by: NWolfram Sang <wsa@sang-engineering.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Signed-off-by: NWolfram Sang <wsa@sang-engineering.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Switch the device tree to the new compatibles introduced in the i2c drivers
to have a common pattern accross all Allwinner SoCs.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Use devm_gpio_request() to make cleanup paths simpler.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Reviewed-by: NVioleta Menendez <violeta.menendez@codethink.co.uk>
Reviewed-by: NIan Molton <ian.molton@codethink.co.uk>
Tested-by: NVioleta Menendez <violeta.menendez@codethink.co.uk>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The i2c-eg20t driver is for a companion chip to the Intel Atom E600
series processors. These are 32-bit x86 processors so the driver is
only needed on X86_32. Add COMPILE_TEST as an alternative, so that the
driver can still be build-tested elsewhere.
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Newer SoCs have so fast input clocks that the ICCL/H registers only
count every second clock to have a meaningful 9-bit range. The driver
was already prepared for that happening, but didn't use it so far.
Add the proper DT configuration for SoCs that need it.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Due to misconfiguration, it can happen that the calculated timing
parameters are out of range. Bail out if that happens. We can also
simplify some logic later because of the verified value. Also, make the
printouts of the values more precise by adding the hex-prefixes.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

sh_mobile_i2c_init() could detect wrong settings, but didn't bail out,
so it would continue unconfigured. Fix this.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Following the KISS principle, remove unneeded stuff.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

This is what devm was made for. No rollback mechanism needed, remove the
hook parameter from the irq setup function and simplify it. While we are
here change some variables to proper types.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Convert the easy parts to devm. irqs will be converted in a seperate
patch to keep diffs readable.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Reported-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Use standard i2c error codes for i2c failures. Also, don't print
something on timeout since it happens regularly with i2c. Simplify some,
logic, too.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

No functional change, binaries are identical.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

HSI2C module on Exynos5260 differs from current modules in
following ways:
1.  HSI2C on Exynos5260 has fifo_depth of 16bytes
2.  Module needs to be reset as a part of init sequence.

Hence, Following changes are involved.
1. Add a new compatible string and Updates the Documentation dt bindings.
2. Introduce a variant struct to support the changes in H/W
3. Reset the module during init. Thus, bringing the module back
to default state irrespective of what firmware did with it.
Signed-off-by: NNaveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: NPankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

This adds some more warnings to the i2c-arb-gpio-challenge docs to
help encourage people not to use it in their designs unless they have
no choice.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Fixed most checkpatch.pl issues
Signed-off-by: NRichard Leitner <me@g0hl1n.net>
Reviewed-by: NJean Delvare <jdelvare@suse.de>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

For !CONFIG_PM_RUNTIME, the device were never put back into active
state while resuming.

For CONFIG_PM_RUNTIME, we blindly trusted the device to be inactive
while we were about to handle it at suspend late, which is just too
optimistic.

Even if the driver uses pm_runtime_put_sync() after each tranfer to
return it's runtime PM resources, there are no guarantees this will
actually mean the device will inactivated. The reason is that the PM
core will prevent runtime suspend during system suspend, and thus when
a transfer occurs during the early phases of system suspend the device
will be kept active after the transfer.

To handle both issues above, use pm_runtime_force_suspend|resume() from
the system suspend|resume callbacks.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The smbus block read is not currently supported for imx i2c devices.
This patchset adds the support to imx i2c bus so that blocks of data
can be read using SMbus block reads.(using i2c_smbus_read_block_data()
function from the i2c_core.c.). Tested with 3.10.9 kernel.
Reviewed-by: NShawn Guo <shawn.guo@freescale.com>
Signed-off-by: NKaushal Butala <kaushalkernelmailinglist@gmail.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The Allwinner A10 compatibles were following a slightly different compatible
patterns than the rest of the SoCs for historical reasons. Move to the other
pattern for consistency across all Allwinner Socs.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
[wsa: dropped binding OK as per
http://lists.infradead.org/pipermail/linux-arm-kernel/2014-February/229438.html]
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Pull two powerpc fixes from Ben Herrenschmidt:
 "Here are a couple of fixes for 3.15.  One from Anton fixes a nasty
  regression I introduced when trying to fix a loss of irq_work whose
  consequences is that we can completely lose timer interrupts on a
  CPU... not pretty.

  The other one is a change to our PCIe reset hook to use a firmware
  call instead of direct config space accesses to trigger a fundamental
  reset on the root port.  This is necessary so that the FW gets a
  chance to disable the link down error monitoring, which would
  otherwise trip and cause subsequent fatal EEH error"

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc: irq work racing with timer interrupt can result in timer interrupt hang
  powerpc/powernv: Reset root port in firmware

Pull two btrfs fixes from Chris Mason:
 "This has two fixes that we've been testing for 3.16, but since both
  are safe and fix real bugs, it makes sense to send for 3.15 instead"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: send, fix incorrect ref access when using extrefs
  Btrfs: fix EIO on reading file after ioctl clone works on it

Pull two ceph fixes from Sage Weil:
 "The first patch fixes a problem when we have a page count of 0 for
  sendpage which is triggered by zfs.  The second fixes a bug in CRUSH
  that was resolved in the userland code a while back but fell through
  the cracks on the kernel side"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  crush: decode and initialize chooseleaf_vary_r
  libceph: fix corruption when using page_count 0 page in rbd

Pull xfs fixes from Dave Chinner:
 "Code inspection of the XFS error number sign translations found a
  bunch of issues, including returning incorrectly signed errors for
  some data integrity operations.

  These leak to userspace and result in applications not getting the
  errors correctly reported.  Hence they need fixing sooner rather than
  later.

  A couple of the bugs are in data integrity operations, a couple more
  are in the new COLLAPSE_RANGE code.  One of these came in through a
  recent ext4 merge and so I had to update the base tree to 3.15-rc5
  before fixing the issues"

* tag 'xfs-for-linus-3.15-rc6' of git://oss.sgi.com/xfs/xfs:
  xfs: list_lru_init returns a negative error
  xfs: negate xfs_icsb_init_counters error value
  xfs: negate mount workqueue init error value
  xfs: fix wrong err sign on xfs_set_acl()
  xfs: fix wrong errno from xfs_initxattrs
  xfs: correct error sign on COLLAPSE_RANGE errors
  xfs: xfs_commit_metadata returns wrong errno
  xfs: fix incorrect error sign in xfs_file_aio_read
  xfs: xfs_dir_fsync() returns positive errno

Pull renameat2 arch support from Miklos Szeredi:
 "I've collected architecture patches for the renameat2 syscall that
  maintainers acked and/or asked me to queue.

  This adds architecture support for the renameat2 syscall to m68k,
  parisc, ia64 and through asm-generic to arc, arm64, c6x, hexagon,
  metag, openrisc, score, tile, unicore32"

* 'renameat2' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
  scripts/checksyscalls.sh: Make renameat optional
  asm-generic: Add renameat2 syscall
  ia64: add renameat2 syscall
  parisc: add renameat2 syscall
  m68k: add renameat2 syscall

Pull iommu fixes from Joerg Roedel:
 "Three fixes for the AMD IOMMU driver:
   - fix a locking issue around get_user_pages()
   - fix two issues with device aliasing and exclusion range handling"

* tag 'iommu-fixes-v3.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu/amd: fix enabling exclusion range for an exact device
  iommu/amd: Take mmap_sem when calling get_user_pages
  iommu/amd: Fix interrupt remapping for aliased devices

Merge tag 'stable/for-linus-3.15-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/ibft

Pull iscsi_ibft fix from Konrad Rzeszutek Wilk:
 "Fix iBFT regression on Broadcom NICs introduced in 3.2"

* tag 'stable/for-linus-3.15-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/ibft:
  iscsi_ibft: Fix finding Broadcom specific ibft sign

Merge tag 'renesas-sh-drivers-for-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas

Pull SH driver fix from Simon Horman:
 "Compile drivers/sh/pm_runtime.c if ARCH_SHMOBILE_MULTI

  This resolves a regression introduced in v3.14 by commit bf98c1ea
  ("ARM: Rename ARCH_SHMOBILE to ARCH_SHMOBILE_LEGACY")"

* tag 'renesas-sh-drivers-for-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  drivers: sh: compile drivers/sh/pm_runtime.c if ARCH_SHMOBILE_MULTI

Pull media fixes from Mauro Carvalho Chehab:
 "Most of the changes are drivers fixes (rtl28xuu, fc2580, ov7670,
  davinci, gspca, s5p-fimc and s5c73m3).

  There is also a compat32 fix and one infoleak fixup at the media
  controller"

* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  [media] V4L2: fix VIDIOC_CREATE_BUFS in 64- / 32-bit compatibility mode
  [media] V4L2: ov7670: fix a wrong index, potentially Oopsing the kernel from user-space
  [media] media-device: fix infoleak in ioctl media_enum_entities()
  [media] fc2580: fix tuning failure on 32-bit arch
  [media] Prefer gspca_sonixb over sn9c102 for all devices
  [media] media: davinci: vpfe: make sure all the buffers unmapped and released
  [media] staging: media: davinci: vpfe: make sure all the buffers are released
  [media] media: davinci: vpbe_display: fix releasing of active buffers
  [media] media: davinci: vpif_display: fix releasing of active buffers
  [media] media: davinci: vpif_capture: fix releasing of active buffers
  [media] s5p-fimc: Fix YUV422P depth
  [media] s5c73m3: Add missing rename of v4l2_of_get_next_endpoint() function
  [media] rtl28xxu: silence error log about disabled rtl2832_sdr module
  [media] rtl28xxu: do not hard depend on staging SDR module