imx6q_opp_check_speed_grading() remaps memory to the base variable and
never unmaps it. I can't see how this can be of any use later so here I
unmap it.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

i.MX platform maintainer Shawn Guo is not happy with the such commit as
explained below [1]:

"The GPR difference between SoCs can be encoded in device tree as well.
It's pointless to repeat the same code pattern for every single
platform, that need to set up GPR bits for enabling magic packet wake
up, while the only difference is the register and bit offset.

The platform code will become quite messy and unmaintainable if every
device driver dump their GPR register setup code into platform.

Sorry, but it's NACK from me."

This reverts commit 456062b3 ("ARM: imx: add FEC sleep mode callback
function").

[1] http://www.spinics.net/lists/netdev/msg310922.htmlSigned-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

i.MX6q/dl, i.MX6SX SOCs enet support sleep mode that magic packet can
wake up system in suspend status. For different SOCs, there have some
SOC specifical GPR register to set sleep on/off mode. So add these to
callback function for driver.
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

System restart mechanism has been changed with the introduction
of "kernel restart handler call chain support". The imx2 watchdog
based restart handler has been moved to the driver, and these
restart can be removed from the machine layer.

This patch cleans up the device tree version machine reset init with
mxc_arch_reset_init_dt and removes corresponding .restart handler,
for the .init_machine that can be handled by system default after
removing the mxc_arch_reset_init_dt, the .init_machine is also removed.
Signed-off-by: NJingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Otherwise GCC will mark the .init.rodata section R/W, which causes
a compile error once we add other real R/O data.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

It is only the mx6quad variant that can run up to 1.2GHz, so add the check
accordingly.

This avoids getting the following warning on a mx6solo:

failed to disable 1.2 GHz OPP
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

This is needed so that the IPU framebuffer scanout cannot be
starved by VPU or GPU activity.
Some boards like the SabreLite and SabreSD seem to set this in
the DCD already, but the documented register reset values do not
contain the necessary settings.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The fuse map of speed_grading[1:0] defines the max speed
of ARM, see below the definition:

2b'11: 1200000000Hz;
2b'10: 996000000Hz;
2b'01: 852000000Hz; -- i.MX6Q Only, exclusive with 996MHz.
2b'00: 792000000Hz;

Need to remove all illegal setpoints according to fuse
map.
Signed-off-by: NAnson Huang <b20788@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

On imx6qdl, the ENET RMII and PTP clock can come from either internal
ANATOP/CCM or external clock source through pad GPIO_16.  But in case
of the external clock source, bit IOMUXC_GPR1[21] needs to be cleared.

The patch adds the support for systems that use an external clock source
and distinguishes above two cases by checking if the PTP clock specified
in device tree is the one coming from the internal ANATOP/CCM.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

When system enter suspend, we can set the DDR IO to
high-Z state to save DDR IOs' power consumption, this
operation can save many power(from ~26mA@1.5V to ~15mA@1.5V,
measured on i.MX6Q SabreSD board, R25) of DDR IOs. To
achieve that, we need to copy the suspend code to ocram
and run the low level hardware related code(set DDR IOs
to high-Z state) in ocram.

If there is no ocram space available, then system will
still do suspend in external DDR, hence no DDR IOs will
be set to high-Z.

The OCRAM usage layout is as below,

ocram suspend region(4K currently):
======================== high address ======================
                              .
                              .
                              .
                              ^
                              ^
                              ^
                      imx6_suspend code
             PM_INFO structure(imx6_cpu_pm_info)
======================== low address =======================
Reviewed-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NAnson Huang <b20788@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add support for the SolidRun HummingBoard.  This commit adds support for
the following interfaces on this board:

- Consumer Ir receiver
- S/PDIF output
- Both USB interfaces
- Gigabit Ethernet using AR8035
- UART port
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

0-DAY kernel build testing backend reports the following.

 scripts/checkpatch.pl 0001-ARM-imx-add-support-code-for-IMX50-based-machines.patch
 # many are suggestions rather than must-fix

 ERROR: Use of const init definition must use __initconst
 #80: arch/arm/mach-imx/mach-imx50.c:26:
 +static const char *imx50_dt_board_compat[] __initdata = {

While at it, fix the error globally for IMX platform.
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Acked-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The PEX860X has GPIO's which are used for PCI Reset lines on the
Gateworks Ventana boards.  The GPIO's need to be set as output
level high so as to allow the PCIe devices to come out of reset.
Signed-off-by: NTim Harvey <tharvey@gateworks.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Since Operating Performance Points (OPP) functions are specific
to device specific power management, be specific and rename opp.h
to pm_opp.h
Reported-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Since Operating Performance Points (OPP) functions are specific to
device specific power management, be specific and rename opp_*
accessors in OPP library with dev_pm_opp_* equivalent.

Affected functions are:
 opp_get_voltage
 opp_get_freq
 opp_get_opp_count
 opp_find_freq_exact
 opp_find_freq_floor
 opp_find_freq_ceil
 opp_add
 opp_enable
 opp_disable
 opp_get_notifier
 opp_init_cpufreq_table
 opp_free_cpufreq_table
Reported-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NNishanth Menon <nm@ti.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

The imx6q_restart() works fine with normal reboot but will run into
problem with emergency reboot like sysrq-b.  In that case, of_iomap()
gets called from interrupt context and hence triggers the BUG_ON in
__get_vm_area_node().

Actually, since commit c1e31d12 (ARM: imx: create
mxc_arch_reset_init_dt() for DT boot), imx6q/dl should try to use
mxc_restart() by calling mxc_arch_reset_init_dt() beforehand, where
things like of_iomap() can be done.

The patch updates mxc_restart() a little bit to get it work for imx6q/dl
and kill imx6q_restart() completely.
Reported-by: NNathan Lynch <nathan_lynch@mentor.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The patch enables soc bus infrastructure and adds a function
imx_soc_device_init() to report soc info via soc device interface for
imx6qdl and imx6sl.  With the support, user space can get soc related
info by looking at sysfs like below.

  $ cat /sys/devices/soc0/machine
  Freescale i.MX6 Quad SABRE Smart Device Board
  $ cat /sys/devices/soc0/family
  Freescale i.MX
  $ cat /sys/devices/soc0/soc_id
  i.MX6Q
  $ cat /sys/devices/soc0/revision
  1.2
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The patch creates a common function imx_init_revision_from_anatop() by
merging imx6q_init_revision() and imx_anatop_get_digprog(), so that any
SoC that encodes revision info in anatop can use it to initialize
revision.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

It calls imx_set_soc_revision() to set up soc revision in
imx6q_init_revision(), and replaces all the occurrences of
imx6q_revision() with common helper imx_get_soc_revision().
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

With arch/arm calling of_clk_init(NULL) from time_init(), we can now
remove custom .init_time hooks.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: NShawn Guo <shawn.guo@linaro.org>

Commit cdc58d60 "cpufreq: imx6q-cpufreq:
remove device tree parsing for cpu nodes" assumed the pdev->dev is set to
cpu0 device in the platform code. But it actually points to the virtual
cpufreq-cpu0 platform device which is not present in the device tree.
Most of the information needed by cpufreq is stored in cpu0 DT node.
So cpu_dev must point to cpu0 device.

This patch fixes the wrong assignment to cpu_dev.
Reported-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NSudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

The CLKO is widely used by imx6q board designs to clock audio codec.
Since most codecs accept 24 MHz frequency, let's initially set up CLKO
with OSC24M (cko <-- cko2 <-- osc).  Then those board specific CLKO
setup for audio codec can be removed.

The board dts files also need an update on cko reference in codec node.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add defines for common Micrel PHY setups so that other platforms
can use them. Update imx61 and sama5 hardware to use the micrel_phy.h
PHY defines.

Also add support for the KSZ9021RLRN PHY.
Signed-off-by: NDinh Nguyen <dinguyen@altera.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
CC: Andrew Victor <linux@maxim.org.za>
CC: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: netdev@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Move anatop related (For USB) from board file to anatop driver
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Now that the cpu device registration initialises the of_node(if available)
appropriately for all the cpus, parsing here is redundant.

This patch removes all DT parsing and uses cpu->of_node instead.
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NSudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>

Move imx6q L2 initialization function imx6q_init_l2cache() into
system.c, and rename it imx_init_l2cache(), so that other platforms
other than imx6q can also use the function.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NDirk Behme <dirk.behme@de.bosch.com>

Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The KSZ9031 is used on the i.MX6 based Data Modul eDM-QMX6
board. It needs the same fixup to the rx/tx delays as other
i.MX6 boards.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The AR8031 is used on the i.MX6 based sabreSD, sabreauto and wandboard.
All need the same fixup, so add it for all i.MX6.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

In current U-Boot the sabrelite, nitrogen6x and titanium all need
the same fixup for the ksz9021 phy. Instead of limiting the fixup
to a single board apply them for all.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Preparing to move the parsing of reboot= to generic kernel code forces
the change in reboot_mode handling to use the enum.

[akpm@linux-foundation.org: fix arch/arm/mach-socfpga/socfpga.c]
Signed-off-by: NRobin Holt <holt@sgi.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Russ Anderson <rja@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

WM8962 needs 24MHz clock for its MCLK, so choose PLL4 as the parent of clko1.
Signed-off-by: NNicolin Chen <b42378@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Instead of explicitly calling clock initialization functions, we can
declare the functions with CLK_OF_DECLARE() and then call common
of_clk_init() to have them invoked properly.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

To improve the performance and power consumption add an i.MX6
specific L2 cache initialization.

This configuration is taken from Freescale's kernel patch

"ENGR00153601 [MX6]Adjust L2 cache parameter" [1]

with two additional improvements:

a) The L2X0_POWER_CTRL has only the two bits we set. So no need
   to read the register before. Remove the register read done
   in Freescale's patch.

b) In the L2X0_PREFETCH_CTRL register, besides the double linefill (bit[30]),
   additionally enable the instruction and data prefetch (bit[29-28]).
Signed-off-by: NDirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

[1] http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/commit/arch/arm/mach-mx6/mm.c?h=imx_3.0.35_12.09.01&id=814656410b40c67a10b25300e51b0477b2bb96d1

The i.MX6 DualLite/Solo is another i.MX6 family SoC, which is highly
compatible with i.MX6 Quad/Dual.  And that's why we choose to support
it using imx6q code with cpu_is_imx6dl() check when necessary.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Function imx_anatop_get_digprog() that reads register ANADIG_DIGPROG is
called to identify silicon version.  Users might query silicon version
earlier than regmap subsystem is ready.  For example, imx6q clock driver
query revision in mx6q_clocks_init(), where regmap is not initialized
yet.

Change imx_anatop_get_digprog() to map anatop block and read
ANADIG_DIGPROG in the native way, so that the function can work at very
early stage.

While at it, let's move imx_print_silicon_rev() back to
imx6q_timer_init() to have the message show up a little earlier.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

So it can be used in clk-imx6q.c for revision dependent clock tree setup.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Anatop module have sereval configurations for user
to reduce the power consumption in suspend, provide
suspend/resume interface for further use and enable
fet_odrive to reduce CORE LDO leakage during suspend.

As we have a common anatop file, remove all the operations
of anatop module in other files, use anatop interfaces to
do that.
Signed-off-by: NAnson Huang <b20788@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Fix the following sparse warnings:

arch/arm/mach-imx/mach-imx6q.c:60:6: warning: symbol 'imx6q_restart' was not declared. Should it be static?
arch/arm/mach-imx/mach-imx6q.c:223:24: warning: symbol 'imx6q_cpufreq_pdev' was not declared. Should it be static?
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Now that we have OF based init with CLKSRC_OF, convert smp_twd init
function to use it and covert all callers of
twd_local_timer_of_register.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-omap@vger.kernel.org
Cc: spear-devel@list.st.com
Reviewed-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>