In DM365 Q0, Q1 and Q2 are used by codecs.
LSP drivers should use Q3.
This patch changes the default queue for DM365.
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This patch adds following changes:-
	1) add sub device configuration data for TVP5146 used by vpfe capture
	2) registers platform devices for vpfe_capture, isif and vpss
	3) defines hardware resources for the devices listed under 2)
	4) defines clock aliase for isif driver
	5) adding setup_pinmux() for isif
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Adds the device_enable function to the DaVinci Keyscan platform data
to setup the PINMUX configuration.

It also removes #ifdef from the DM365 EVM board in order to load it
properly as a module.
Signed-off-by: NMiguel Aguilar <miguel.aguilar@ridgerun.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The general structures are defined at DM365 SoC file and the specific
platform data structure for the EVM is defined at board file.
Signed-off-by: NMiguel Aguilar <miguel.aguilar@ridgerun.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The general structures are defined at DM365 SoC file and the specific
platform data structure for the EVM is defined at board file.
Signed-off-by: NMiguel Aguilar <miguel.aguilar@ridgerun.com>

There have accumulated quite a lot of them after the code reorganizations...

In several cases I had to replace #include <linux/dma-mapping.h> which wasn't
needed directly but happened to #include <linux/err.h> which was needed.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

1) Registers the platform device for McBSP on dm365.
2) Add platform data to DM365 EVM board file.
3) Set i2c address for audio codec at DM365 EVM board file.
Signed-off-by: NMiguel Aguilar <miguel.aguilar@ridgerun.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The parent clock for the USB source clock is actually PLL1 aux clock,
not PLL2 sysclk1.
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This patch adds definitions for some DM365 IRQs that are used by
the codecs. Codecs will also use the IRQs.
Entries are being added to enable/disable IRQ's.
There is no use as such for these entires in the kernel itself.
Instead these will be used by the "linuxutils" package of the DVSDK.

For further information on IRQ muxing refer to
http://focus.ti.com/lit/ug/sprufg5a/sprufg5a.pdfSigned-off-by: NSandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: NSneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

DM365 RBL has been updated. The variant number has changed for this
new revision of silicon. This patch adds support for the
new revision of DM365.
The name fields are also being updated to reflect the version
of the silicon.

Without this minor fix DM365 REV 1.2 will not boot up
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The mask can hold only 8 bit values. This gave a
compilation warning. This patch rectifies the warning.
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

EDMA queues in DM365 are a little different than those
on other DaVinci's. On DM365 Q0 and Q1 have the larger
FIFO size. We want Q0 and Q1 to be used by codecs and
DVSDK demos.
MMC driver is the only driver which uses the flag
'EVENTQ_DEFAULT'. So MMC driver should be using Q2 instead of
Q1 on DM365.
This patch allows us to declare a "default queue" from
SOC specific code. If it is not declared then the EDMA
driver assumes a default of queue 1.
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Support DM365 GPIOs ... primarily by handling non-banked GPIO IRQs:

 - Flag DM365 chips as using non-banked GPIO interrupts, using a
   new soc_info field.

 - Replace the gpio_to_irq() mapping logic.  This now uses some
   runtime infrastructure, keyed off that new soc_info field,
   which doesn't handle irq_to_gpio().

 - Provide a new irq_chip ... GPIO IRQs handled directly by AINTC
   still need edge triggering managed by the GPIO controller.

DM365 chips no longer falsely report 104 GPIO IRQs as they boot.

Intelligence about IRQ muxing is missing, so for the moment this
only exposes the first eight DM365 GPIOs, which are never muxed.
The next eight are muxed, half with Ethernet (which uses most of
those pins anyway).

Tested on DM355 (10 unbanked IRQs _or_ 104 banked ones) and also
on DM365 (16 unbanked ones, only 8 made available).
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Patch updates DM365 PINMUX by adding entries for Video, SPI 1 - 4,
PWM 0 - 3.
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The patch adds Support for EMAC in the DM365 SOC and
the DM365 EVM board.
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The patch adds base support for new TI SOC DM365, which s
similar to the dm355.
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>