1. 26 3月, 2008 2 次提交
  2. 14 3月, 2008 7 次提交
  3. 01 3月, 2008 10 次提交
    • I
      rt2x00: Cleanup mode registration · 31562e80
      Ivo van Doorn 提交于
      Don't wildly pass any number for num_rates to rt2x00lib,
      instead pass which type of rates are supported (CCK, OFDM).
      Same for num_modes but then for the 2GHZ and 5GHZ band.
      
      This makes the interface look much nicer and makes
      extending it later easier.
      Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
      Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
      31562e80
    • I
      rt2x00: Remove reset_tsf() · ef8f66cd
      Ivo van Doorn 提交于
      Specifications indicate the TSF registers are read-only,
      so there is no point in writing 0 to those registers.
      
      As far as I know there isn't another way to reset the
      TSF registers. So removing these callbacks will notify
      mac80211 about the lack of support.
      Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
      Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
      ef8f66cd
    • I
      rt2x00: Fix Descriptor DMA initialization · 30b3a23c
      Ivo van Doorn 提交于
      As Adam Baker reported the DMA address for the
      descriptor base was incorrectly initialized in
      the PCI drivers.
      
      Instead of the DMA base for the descriptor, the
      DMA base for the data was passed resulting in a
      broken TX/RX state for PCI drivers.
      Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
      Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
      30b3a23c
    • I
      rt2x00: Don't report driver generated frames to tx_status() · baf26a7e
      Ivo van Doorn 提交于
      This adds a new flag for the skb_frame_desc structure which is used to tag
      rts/cts frames that are generated by the driver. Through the tag we can
      recognize frames we have generated ourselves, so we don't report their tx
      status to mac80211.
      
      This patch is based on the original patch by
      Mattias Nissler <mattias.nissler@gmx.de>.
      Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
      Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
      baf26a7e
    • I
      rt2x00: Make rt2x00 less verbose · 25fd893d
      Ivo van Doorn 提交于
      Remove the debug messages regarding initialization from
      EEPROM. The values are vendor specific, and are not really
      needed for debug purposes. If they ever become usefull we
      still have access to them through debugfs which also
      prints the exact same values...
      Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
      Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
      25fd893d
    • I
      rt2x00: Make use of MAC80211_LED_TRIGGERS · a9450b70
      Ivo van Doorn 提交于
      Make use of the led triggers provided by mac80211 to control
      the led status. This can be enabled through a per-driver
      configuration option which will automatically enable the
      generic handler in rt2x00lib.
      
      This has been enabled for rt2500usb and rt73usb for the moment
      since the led class will call set_brightness in irq context which
      will not work correctly with the usb drivers who need to sleep.
      Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
      Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
      a9450b70
    • I
      rt2x00: Move beacon and atim queue defines into rt2x00 · 5957da4c
      Ivo van Doorn 提交于
      As Johannes Berg indicated the BEACON and AFTER_BEACON
      queue indeces in mac80211 should be removed because they
      are too hardware specific. This patch adds the queue index
      defines into rt2x00queue.h and removes the dependency of
      the defines inside mac80211.h.
      
      Also move rt2x00pci_beacon_update() into rt2400pci and
      rt2500pci individually since it is no longer a generic
      function since rt61 and rt2800 no longer use that.
      Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
      Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
      5957da4c
    • I
      rt2x00: Add per-interface structure · 6bb40dd1
      Ivo van Doorn 提交于
      Rework the interface handling. Delete the interface structure
      and replace it with a per-interface structure. This changes the
      way rt2x00 handles the active interface drastically.
      
      Copy ieee80211_bss_conf to the this rt2x00_intf structure during
      the bss_info_changed() callback function. This will allow us to
      reference it later, and removes the requirement for the device flag
      SHORT_PREAMBLE flag which is interface specific.
      
      Drivers receive the option to give the maximum number of virtual
      interfaces the device can handle. Virtual interface support:
      rt2400pci: 1 sta or 1 ap, * monitor interfaces
      rt2500pci: 1 sta or 1 ap, * monitor interfaces
      rt2500usb: 1 sta or 1 ap, * monitor interfaces
      rt61pci: 1 sta or 4 ap, * monitor interfaces
      rt73usb: 1 sta or 4 ap, * monitor interfaces
      
      At the moment none of the drivers support AP and STA interfaces
      simultaneously, this is a hardware limitation so future support
      will be very unlikely.
      
      Each interface structure receives its dedicated beacon entry,
      with this we can easily work with beaconing while multiple master
      mode interfaces are currently active.
      
      The configuration handlers for the MAC, BSSID and type are
      often called together since they all belong to the interface
      configuration. Merge the 3 configuration calls and cleanup
      the API between rt2x00lib and the drivers. While we are cleaning
      up the interface configuration anyway, we might as well clean up
      the configuration handler as well.
      Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
      Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
      6bb40dd1
    • I
      rt2x00: Queue handling overhaul · 181d6902
      Ivo van Doorn 提交于
      This introduces a big queue handling overhaul, this also
      renames "ring" to "queues".
      
      Move queue handling into rt2x00queue.c and the matching header,
      use Kerneldoc to improve rt2x00 library documentation.
      
      Access to the queues is now protected under a spinlock, this
      to prevent race conditions which could corrupt the indexing
      system of the queue.
      
      Each queue entry allocates x bytes for driver/device specific data,
      this cleans up the queue structure significantly and improves
      code readability.
      
      rt2500usb no longer needs 2 entries in the beacon queue to correctly
      send out the guardian byte. This is now handled in the entry specific
      structure.
      
      rt61 and rt73 now use the correct descriptor size for beacon frames,
      since this data is written into the registers not the entire TXD
      descriptor was used but instead of a subset of it named TXINFO.
      
      Finally this also fixes numerous other bugs related to incorrect
      beacon handling or beacon related code.
      Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
      Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
      181d6902
    • I
      rt2x00: Update copyright notice · 811aa9ca
      Ivo van Doorn 提交于
      Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
      Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
      811aa9ca
  4. 28 2月, 2008 1 次提交
  5. 29 1月, 2008 16 次提交
  6. 11 10月, 2007 4 次提交