This is needed if we take over after drivers which use those.
Signed-off-by: NJakub Kicinski <kubakici@wp.pl>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Reviewed-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Don't immediately abort .start if DMA is busy before we
initialize the queues. Some drivers do not deinitialize
queues properly and we would fail to take over after them.

This behaviour is consistent with legacy driver.
Signed-off-by: NJakub Kicinski <kubakici@wp.pl>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Reviewed-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Legacy driver disables DMA before loading firmware.
Signed-off-by: NJakub Kicinski <kubakici@wp.pl>
Reviewed-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Introduce wpdma_disable function to simplify the code.
Signed-off-by: NJakub Kicinski <kubakici@wp.pl>
Reviewed-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Before we send probes in connection monitoring we check if scan is not
pending. But we do that check without locking. Fix that and also do not
start scan if connection monitoring is in progress.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Having the pointer to lib_ops in the config
makes it impossible to split the driver into
different modules. Determine the ops based on
the device family enumeration to get rid of
the direct pointer.

Also move all the opmode specific code from
the iwl-[1256]000.c files into a new file
iwl-agn-devices.c so that the former only
have configuration data now.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Driver doesn't report its supported cipher suites through cfg80211
interface. It still uses wext interface and probably will not work
through nl80211, but will at least correctly advertise supported
features.

Bug was reported by Omar Siam.
https://bugzilla.kernel.org/show_bug.cgi?id=43049Signed-off-by: NStanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJim Cromie <jim.cromie@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJim Cromie <jim.cromie@gmail.com>
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We were sending the LTO TLV as a version TLV instead of the actual link
timeout one.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When buffers on the receiption path exceed 262 bytes, the pn533 uses
a chaining mechanism where the initiator has to send NULL data frames
to fetch the remaining frames.
We do that from a workqueue context while holding the cmd lock. Once the
MI bit is gone, we aggregate the queued received skbs.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is no need for soft IRQ contexts, and workqueues are more flexible.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

dsap and ssap were swapped when sending DN or DISC.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The if logic could lead to zero length TLVs.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

recv_n is set properly when receiving an HDLC frame.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

At KERN_DEBUG level.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some HW/drivers get notifications when a tag moves out of the radio field.
This notification is now forwarded to user space through netlink.
Signed-off-by: NEric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NEric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NEric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The target index can be used by userspace to uniquely identify a target
and thus should be kept unique, per NFC adapter. Moreover, some protocols
do not provide a logical index when discovering new targets, so we have to
generate one for them.
For NCI or pn533 to fetch their logical index, we added a logical_idx field
to the target structure.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NEric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Most NFC HCI chipsets actually use a simplified HDLC link layer to
carry HCI payloads.
This implementation registers itself as an HCI device on behalf of the
NFC driver.
Signed-off-by: NEric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is an implementation of ETSI TS 102 622 specification.
Many NFC chipsets use HCI as the host <-> target protocol on top of a
serial link like i2c.
Signed-off-by: NEric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

NFC drivers will call this routine when they detect that a tag leaves the
RF field. This will eventually lead to the corresponding netlink event
to be sent.
Signed-off-by: NEric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some chips are capable of detecting when a tag is out of the field, so
they could send a netlink event about it to userspace.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Clean up some orphaned code lines containing
* unused variables (not referenced / write-only)
* non-implemented function prototypes
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Record the RANN sender's address only for RANNs that meet the acceptance
criteria (per sections 13.10.12.4.2).
Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com>
Reviewed-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make use of request_firmware_nowait instead of request_firmware
to load FW asynchronously. This fixes timeouts introduced with
recent udev changes.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patches enables setting association request and probe request
IE for station interface. WPS exchange between WPS2.0 AP and mwifiex
STA Enrollee/External Registrar completes successfully.

Tested with wpa_supplicant 1.0 and 2.0 devel.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use "priv->country_code" string to display country information in
debugfs command "info" instead of "adapter->region_code".

"adapter->region_code" contains default region code got from FW while
initialization, whereas "priv->country_code" is updated in reg_notifier
handler whenever there is a change in regulatory domain.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Driver gets region code from FW during initialisation. This patch
makes use of it for settting default regulatory domain using
regulatory_hint() API.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is a copy-n-paste error introduced in recent patch
"mwifiex: add set_cqm_rssi_config handler support".
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This will later be used to dynamically bind
the configuration data for DVM and MVM.

For now, we can use it to get rid of the
additional_nic_config() hook.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The iwl-shared.h header file will be going away
soon. There isn't much left in it that we keep,
other than the device configuration declarations.
Move those out now to a new iwl-config.h header.
iwl-cfg.h seemed like a possible alternative but
those declarations will later live in the PCIe
transport code.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The whole code around eeprom is distributed
across whole bunch of different files, most
of which belong to the to-be-DVM code. As a
result, it is currently very hard to split
out the EEPROM code to be generic. However,
it is also quite unlikely that the current
EEPROM code will be needed by the MVM code
as that has different mechanisms to query
the EEPROM (it does so through the uCode.)

So, at least temporarily, move everything
into priv. If it becomes necessary to use
the code from MVM, we will have to split it
out, but then it's also easier since we'll
know what pieces we need.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Split the force_reset debugfs file into two
different files:
 * "rf_reset" triggers a reset of the RF when
   written to and exposes statistics on RF
   resets when read
 * fw_restart triggers a firmware restart when
   written to and lives in the transport

This cleans up all sources of firmware restart
to originate within the transport layer and
allows us to simplify some code.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This defaults to false, and we don't recommend
to use it anywhere, so just remove it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>