[why]
The issue is specific for linux, as on timings such as 8K@60
or 4K@144 DSC should be working in combination with ODM Combine
in order to ensure that we can run those timings. The validation
for those timings was passing, but when pipe split was happening
second pipe wasn't being programmed.

[how]
Rebuild mapped resources if we split stream for ODM.
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why] Underflow occurs on some display setups(repro'd on 3x4K HDR) on boot,
mode set, and hot-plugs with. Underflow occurs because mem clk
is not set high after disabling pstate switching. This behaviour occurs
because some calculations assumed displays were synchronized.

[How] Add a condition to check if timing sync is disabled so that
synchronized vblank can be set to false.
Signed-off-by: NJaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: NAlvin Lee <Alvin.Lee2@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
DML diags tests are failing because the struct contents get
clobbered by a memcpy.

[How]
Remove the memcpy call.
Signed-off-by: NIlya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Update bw validation to use prev and next odm pipe pointers
for populating dml inputs.
Signed-off-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: NCharlene Liu <Charlene.Liu@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Currently odm is handled using top_bottom pipe by special casing
the differing opps to differentiate from mpc combine.

Since top/bottom pipe list was made to track mpc muxing this creates
difficulties in adding a 4 pipe odm case support.

Rather than continue using mpc combine list, this change reworks odm
to use it's own linked list to keep track of odm combine pipes. This
also opens up options for using mpo with odm, if a practical use case
is ever found.
Signed-off-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: NCharlene Liu <Charlene.Liu@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]

Previous SOC bounding box firmware loading logic was for NV10, when we
still had it in firmware. Now that it's brought into driver code, and
NV12 BB is in firmware, this logic needs to be repurposed for NV12.

[How]

Set SOC_BOUNDING_BOX_VALID to false, and add the dcn_2_0_nv12_soc BB
struct. In init_soc_bounding_box, load firmware to nv12 BB instead.

In addition, conditionally update and patch the BB, depending on ASIC
REV.
Signed-off-by: NLeo Li <sunpeng.li@amd.com>
Reviewed-by: NHersen Wu <hersenxs.wu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Currently the paremeters are extracted as if dml is calculating
using pipes as we pass them in. in reality, dml internally merges
pipes into planes if pipe split is detected.

This change adds reverse logic to dcn20_calculate_dlg_params so
that the global sync parameters can be correctly extracted for
all the pipes when pipe split is enabled.
Signed-off-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: NCharlene Liu <Charlene.Liu@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
Resource mapping done in dcn20_validate_bandwidth has a flaw:  When a full
update is performed, the HWSS will only update the MPCC tree for the stream
that is updated as opposed to all streams.  This means that when mapping pipes
in validation, care must be taken to not change any existing mapping, otherwise it
leads to partial hw programming

[how]
it's not strictly necessary to track which stream/mpcc tree is being updated, but
rather it's sufficient to compare current and new state and just keep pipes that were
previously already mapped unchanged.
Signed-off-by: NJun Lei <Jun.Lei@amd.com>
Reviewed-by: NEric Yang <eric.yang2@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
Previous "less risky" implemenation of 3 tiered fallback is no longer necessary since
DMLv2 has gone through proper validation.  v2 can now be used as the default and 1
level of fallback can be removed

[how]
remove previous workaround implemenation
Signed-off-by: NJun Lei <Jun.Lei@amd.com>
Reviewed-by: NNicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
DC does not correct account for the fact that DPP DTO is double buffered while DPP ref is not.
This means that when DPP ref clock is lowered when it's "safe to lower", the DPP blocks that need
an increased divider will temporarily have actual DPP clock drop below minimum while DTO
double buffering takes effect.  This results in temporary underflow.

[how]
To fix this, DPP clock cannot be programmed atomically, but rather be broken up into the DTO and the
ref.  Each has a separate "safe to lower" logic.  When doing "prepare" the ref and dividers may only increase.
When doing "optimize", both may decrease.  It is guaranteed that we won't exceed max DPP clock because
we do not use dividers larger than 1.
Signed-off-by: NJun Lei <Jun.Lei@amd.com>
Reviewed-by: NEric Yang <eric.yang2@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This should be 'dce_audio_mask', not 'dce_aduio_mask'.
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
We were previously forcing the uclk for every state to max and reducing
the switch time to prevent uclk switching from occuring. This workaround
was previously needed in order to avoid hangs + underflow under certain
display configurations.

Now that DC has the proper fix complete we can drop the hacks and
improve power for most display configurations.

[How]
We still need the function pointers hooked up to grab the real uclk
states from pplib. The rest of the prior hack can be reverted.

The key requirements here are really just DC support, updated firmware,
and support for disabling p-state support when needed in pplib/smu.

When these requirements are met uclk switching works without underflow
or hangs.

Fixes: 02316e96 ("drm/amd/display: Force uclk to max for every state")
Signed-off-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
In order to support uclk switching on NV10 the SOC bounding box
needs to be updated.

[How]
We currently read the constants from the gpu info FW, but supporting
workarounds in DC for different versions of the FW adds additional
complexity to the codebase.

NV10 has been released so it's cleanest to keep the bounding box and
source code in sync by embedding the bounding box like we do for
other ASICs.

Fixes: 02316e96 ("drm/amd/display: Force uclk to max for every state")
Signed-off-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
Existing support in DC for pstate only accounts for a single latency.  This is sufficient when the
variance of latency is small, or that pstate support isn't necessary for correct ASIC functionality.

Newer ASICs violate both existing assumptions.  PState support is mandatory of correct ASIC
functionality, but not all latencies have to be supported.  Existing code supports a "full p state" which
allows memory clock to change, but is hard for DCN to support (as it requires very large buffers).
New code will now fall back to a "dummy p state" support when "full p state" cannot be support.
This easy p state support should always be allowed.

[how]
Define a new latency in socBB.  Add fallback logic to support it.  Note DML is also updated to ensure
that fallback will always work.
Signed-off-by: NJun Lei <Jun.Lei@amd.com>
Reviewed-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
update_bounding_box calculates intermediate bb states based on clock relationship
however, the last state doesn't need to maintain a minimum relationship, but should
actually contain maximum of every clock.  otherwise maximum clocks are not usable

[how]
once the calculated bb is built, override the last state with max values
Signed-off-by: NJun Lei <Jun.Lei@amd.com>
Reviewed-by: NAric Cyr <Aric.Cyr@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Add dual plane dcc programming support for
surfaces.

Removes unions from plane size and dcc params as they
serve no practical purpose only making our code
more convoluted. This results in easy dual plane
dcc and surface size programming.

Temporary diags_dm code is used to handle the interface
change without breaking functionality as a diags change
needs to be applied after this one.
Signed-off-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: NCharlene Liu <Charlene.Liu@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This allows to set a minimum display and dpp clock on dcn2+ HW
by adjusting clocks used for dml calculations.
Signed-off-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

add dc_set_clock
add dc_get_clock

this is for testing and diagnostics to get/set DPPCLK and DISPCLK.
Signed-off-by: NCharlene Liu <charlene.liu@amd.com>
Reviewed-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Unintentionally introduced behaviour change from previous refactor,
which causes clks to be 0 in no stream cases, which will cause
divide by 0.

[How]
Skip calculation of clocks when no stream. Which is the same as old
behaviour.
Signed-off-by: NEric Yang <Eric.Yang2@amd.com>
Reviewed-by: NTony Cheng <tong.cheng@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
Due to limitation in SMU/PPLIB, it is not possible to know Fmax @ Vmin for DCFCLK.
This causes issues at high display configurations where extra headroom of DCFCLK
can enable P-state switching

[how]
Use existing override logic.  If override not defined, then force
min = 507
Signed-off-by: NJun Lei <Jun.Lei@amd.com>
Reviewed-by: NEric Yang <eric.yang2@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
For better readability and reusability

[How]
Move snippets of BW calculation code into helpers.
Signed-off-by: NEric Yang <Eric.Yang2@amd.com>
Reviewed-by: NFatemeh Darbehani <Fatemeh.Darbehani@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

not used.
Signed-off-by: NXiaojie Yuan <xiaojie.yuan@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Change the pipes to 5 if the asic is nv14

This is a temp patch, there was some refactor in the dml part of the code.
which is not in this branch. for now this is good, we can implement this
properly once we have an updated branch.
Signed-off-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
Due to limitation in SMU/PPLIB, it is not possible to know Fmax @ Vmin for DCFCLK.
This causes issues at high display configurations where extra headroom of DCFCLK
can enable P-state switching

[how]
Use existing override logic.  If override not defined, then force
min = 507
Signed-off-by: NJun Lei <Jun.Lei@amd.com>
Reviewed-by: NEric Yang <eric.yang2@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Workaround for now to avoid underflow.

The uclk switch time should really be bumped up to 404, but doing so
would expose p-state hang issues for higher bandwidth display
configurations.
Signed-off-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

clang complains that 'false' is a not a pointer:

drivers/gpu/drm/amd/amdgpu/../display/dc/dcn20/dcn20_resource.c:2428:10: error: expression which evaluates to zero treated as a null pointer constant of type 'struct pipe_ctx *' [-Werror,-Wnon-literal-null-conversion]
                return false;

Changing it to 'NULL' looks like the right thing that will shut up
the warning and make it easier to read, while not changing behavior.

Fixes: 7ed4e635 ("drm/amd/display: Add DCN2 HW Sequencer and Resource")
Reviewed-by: NNathan Chancellor <natechancellor@gmail.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

On 32-bit architectures, dividing a 64-bit integer in the kernel
leads to a link error:

ERROR: "__udivdi3" [drivers/gpu/drm/amd/amdgpu/amdgpu.ko] undefined!
ERROR: "__divdi3" [drivers/gpu/drm/amd/amdgpu/amdgpu.ko] undefined!

Change the two recently introduced instances to a multiply+shift
operation that is also much cheaper on 32-bit architectures.
We can do that here, since both of them are really 32-bit numbers
that change a few percent.

Fixes: bedbbe6a ("drm/amd/display: Move link functions from dc to dc_link")
Fixes: f18bc4e5 ("drm/amd/display: update calculated bounding box logic for NV")
Acked-by: NSlava Abramov <slava.abramov@amd.com>
Tested-by: NSlava Abramov <slava.abramov@amd.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Inconsistent indentation and mixed use of brackets.
Signed-off-by: NErnst Sjöstrand <ernstp@gmail.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

during navi10 bring up, dwb causes system hang.
to continue debug major issue, disable dwb by
set num-dwb = 0. the hang issue is not reproduced now
by enable num-dwb =1. dc source is shared by all os.
win needs num-dwb = 1.
Signed-off-by: Nhersen wu <hersenxs.wu@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NRoman Li <Roman.Li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
For debugging underflow issues it can be useful to have asserts when the
underflow initially occurs.

[How]
Read the underflow status registers after actions that have a high risk
of causing underflow and assert that no underflow occurred. If underflow
occurred, clear the bit.
Signed-off-by: NThomas Lim <Thomas.Lim@amd.com>
Reviewed-by: NEric Yang <eric.yang2@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Currently vmid is decided internally inside dc. With the introduction
of new asics we are required to coordinate vmid use with external
components.

This change converts vmid logic to a DAL module allowing vmid to be
passed in as a parameter to DC.
Signed-off-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: NCharlene Liu <Charlene.Liu@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Description]
dcn2 use fixed clocks and not program DPP CLK or Disp_CLK.
Signed-off-by: NCharlene Liu <charlene.liu@amd.com>
Reviewed-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
Existing behavior has overlapping ranges resulting in path
dependent SMU selection

[how]
Make ranges non-overlapping, resulting in non-path dependent
selection
Signed-off-by: NJun Lei <Jun.Lei@amd.com>
Reviewed-by: NEric Yang <eric.yang2@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

required for new checks.
Signed-off-by: NCharlene Liu <charlene.liu@amd.com>
Reviewed-by: NCharlene Liu <Charlene.Liu@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
The output_bpp pipe parameter was assigned an incorrect value
(color depth enum), and subsequently used to overwrite
the OutputBpp parameter calculated by DML. Seems like this had no
effect except with DSC enabled, which would make DML produce
bad outputs.

[How]
Removed assignment to OutputBpp, fixed output_bpp assignment,
and properly set ForcedOutputLinkBPP instead of OutputBpp.
Also removed condition in DML that prevented forcing of
Output BPP with DSC enabled.
Signed-off-by: NIlya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
Currently DSC power gating is disabled by default because the power
transition doesn't happen, causing a crash on some systems

[how]
Fix the lack of power state transition and enable DSC power gating
by default.
Signed-off-by: NNikola Cornij <nikola.cornij@amd.com>
Reviewed-by: NMartin Leung <Martin.Leung@amd.com>
Reviewed-by: NNevenko Stupar <Nevenko.Stupar@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
dsc adjustment is allowed via stream update sequence.
dsc enablement is only allowed via commit stream sequence.
with the current unified dsc set function, it is hard
to determine which sequence it is called by.
The solution is to decouple dsc adjustment out of enablement
sequence so we can handle them separately.

[how]
decouple dsc adjustment out of enablement.
Signed-off-by: NWenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: NNikola Cornij <Nikola.Cornij@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
current DML logic uses currently trained setting for number
of dp lanes in DML calculations.  this is obviously flawed since
just because 1 lane is in use doesn't mean only 1 lane can be used

this causes mode validation to fail depending on current state,
which is incorrect

[how]
DML should always assume 4 lanes are available.  validation of
bandwidth is not supposed to be handled by DML, since we do
link validation without DML already

also, DML is expecting there to be a copy of the max state, this
state is removed when update_bounding_box is called to update
actual SKU clocks.  fix this as well by duping last state.
Signed-off-by: NJun Lei <Jun.Lei@amd.com>
Reviewed-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: NEric Yang <eric.yang2@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]
DCN code should make as few references to DCE as possible

[HOW]
Copy DCE110 implementation of find_first_free_match_stream_enc_for_link
into DCN10
Signed-off-by: NWesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]
From DCE110 onward, we have the ability to assign DIG BE and FE
separately for any display connector type; before, we could only do this
for DP.
Signed-off-by: NWesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>