Start phylink instance and resume back the PHY to supply
RX clock to MAC before MAC layer initialization by calling
.stmmac_hw_setup(), since DMA reset depends on the RX clock,
otherwise DMA reset cost maximum timeout value then finally
timeout.

Fixes: 74371272 ("net: stmmac: Convert to phylink and remove phylib logic")
Signed-off-by: NFugang Duan <fugang.duan@nxp.com>
Signed-off-by: NJoakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix an issue where dump stack is printed on suspend resume flow due to
netif_set_real_num_rx_queues() is not called with rtnl_lock held().

Fixes: 686cff3d ("net: stmmac: Fix incorrect location to set real_num_rx|tx_queues")
Reported-by: NChristophe ROULLIER <christophe.roullier@st.com>
Tested-by: NChristophe ROULLIER <christophe.roullier@st.com>
Cc: Alexandre TORGUE <alexandre.torgue@st.com>
Reviewed-by: NOng Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: NWong Vee Khee <vee.khee.wong@intel.com>
Link: https://lore.kernel.org/r/20201115074210.23605-1-vee.khee.wong@intel.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

Commit 0366f7e0 ("net: stmmac: add ethtool support for get/set
channels") refactored channel initialization, but during that operation,
the spinlock initialization got lost. Fix this. This fixes the following
lockdep warning:

meson8b-dwmac ff3f0000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 1 PID: 331 Comm: kworker/1:2H Not tainted 5.9.0-rc3+ #1858
Hardware name: Hardkernel ODROID-N2 (DT)
Workqueue: kblockd blk_mq_run_work_fn
Call trace:
 dump_backtrace+0x0/0x1d0
 show_stack+0x14/0x20
 dump_stack+0xe8/0x154
 register_lock_class+0x58c/0x590
 __lock_acquire+0x7c/0x1790
 lock_acquire+0xf4/0x440
 _raw_spin_lock_irqsave+0x80/0xb0
 stmmac_tx_timer+0x4c/0xb0 [stmmac]
 call_timer_fn+0xc4/0x3e8
 run_timer_softirq+0x2b8/0x6c0
 efi_header_end+0x114/0x5f8
 irq_exit+0x104/0x110
 __handle_domain_irq+0x60/0xb8
 gic_handle_irq+0x58/0xb0
 el1_irq+0xbc/0x180
 _raw_spin_unlock_irqrestore+0x48/0x90
 mmc_blk_rw_wait+0x70/0x160
 mmc_blk_mq_issue_rq+0x510/0x830
 mmc_mq_queue_rq+0x13c/0x278
 blk_mq_dispatch_rq_list+0x2a0/0x698
 __blk_mq_do_dispatch_sched+0x254/0x288
 __blk_mq_sched_dispatch_requests+0x190/0x1d8
 blk_mq_sched_dispatch_requests+0x34/0x70
 __blk_mq_run_hw_queue+0xcc/0x148
 blk_mq_run_work_fn+0x20/0x28
 process_one_work+0x2a8/0x718
 worker_thread+0x48/0x460
 kthread+0x134/0x160
 ret_from_fork+0x10/0x1c

Fixes: 0366f7e0 ("net: stmmac: add ethtool support for get/set channels")
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20201029185011.4749-1-m.szyprowski@samsung.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

Ethtool manual stated that the tx-timer is the "the amount of time the
device should stay in idle mode prior to asserting its Tx LPI". The
previous implementation for "ethtool --set-eee tx-timer" sets the LPI TW
timer duration which is not correct. Hence, this patch fixes the
"ethtool --set-eee tx-timer" to configure the EEE LPI timer.

The LPI TW Timer will be using the defined default value instead of
"ethtool --set-eee tx-timer" which follows the EEE LS timer implementation.

Changelog V2
*Not removing/modifying the eee_timer.
*EEE LPI timer can be configured through ethtool and also the eee_timer
module param.
*EEE TW Timer will be configured with default value only, not able to be
configured through ethtool or module param. This follows the implementation
of the EEE LS Timer.

Fixes: d765955d ("stmmac: add the Energy Efficient Ethernet support")
Signed-off-by: NVineetha G. Jaya Kumaran <vineetha.g.jaya.kumaran@intel.com>
Signed-off-by: NVoon Weifeng <weifeng.voon@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add option in plat_stmmacenet_data struct to enable VLAN Filter Fail
Queuing. This option allows packets that fail VLAN filter to be routed
to a specific Rx queue when Receive All is also set.

When this option is enabled:
- Enable VFFQ only when entering promiscuous mode, because Receive All
  will pass up all rx packets that failed address filtering (similar to
  promiscuous mode).
- VLAN-promiscuous mode is never entered to allow rx packet to fail VLAN
  filters and get routed to selected VFFQ Rx queue.
Reviewed-by: NVoon Weifeng <weifeng.voon@intel.com>
Reviewed-by: NOng Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: NChuah, Kim Tatt <kim.tatt.chuah@intel.com>
Signed-off-by: NOng Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As part of the W=1 cleanups for ethernet, a million [*] driver
comments had to be cleaned up to get the W=1 compilation to
succeed. This change finally makes the drivers/net/ethernet tree
compile with W=1 set on the command line. NOTE: The kernel uses
kdoc style (see Documentation/process/kernel-doc.rst) when
documenting code, not doxygen or other styles.

After this patch the x86_64 build has no warnings from W=1, however
scripts/kernel-doc says there are 1545 more warnings in source files, that
I need to develop a script to fix in a followup patch.

The errors fixed here are all kdoc of a few classes, with a few outliers:
In file included from drivers/net/ethernet/qlogic/netxen/netxen_nic_hw.c:10:
drivers/net/ethernet/qlogic/netxen/netxen_nic.h:1193:18: warning: ‘FW_DUMP_LEVELS’ defined but not used [-Wunused-const-variable=]
 1193 | static const u32 FW_DUMP_LEVELS[] = { 0x3, 0x7, 0xf, 0x1f, 0x3f, 0x7f, 0xff };
      |                  ^~~~~~~~~~~~~~
... repeats 4 times...
drivers/net/ethernet/sun/cassini.c:2084:24: warning: suggest braces around empty body in an ‘else’ statement [-Wempty-body]
 2084 |    RX_USED_ADD(page, i);
drivers/net/ethernet/natsemi/ns83820.c: In function ‘phy_intr’:
drivers/net/ethernet/natsemi/ns83820.c:603:6: warning: variable ‘tbisr’ set but not used [-Wunused-but-set-variable]
  603 |  u32 tbisr, tanar, tanlpar;
      |      ^~~~~
drivers/net/ethernet/natsemi/ns83820.c: In function ‘ns83820_get_link_ksettings’:
drivers/net/ethernet/natsemi/ns83820.c:1207:11: warning: variable ‘tanar’ set but not used [-Wunused-but-set-variable]
 1207 |  u32 cfg, tanar, tbicr;
      |           ^~~~~
drivers/net/ethernet/packetengines/yellowfin.c:1063:18: warning: variable ‘yf_size’ set but not used [-Wunused-but-set-variable]
 1063 |   int data_size, yf_size;
      |                  ^~~~~~~

Normal kdoc fixes:
warning: Function parameter or member 'x' not described in 'y'
warning: Excess function parameter 'x' description in 'y'
warning: Cannot understand <string> on line <NNN> - I thought it was a doc line

[*] - ok it wasn't quite a million, but it felt like it.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch add support to --show-ring & --set-ring Ethtool functions:
- Adding min, max, power of two check to new ring parameter's value.
- Bring down the network interface before changing the value of ring
  parameters.
- Bring up the network interface after changing the value of ring
  parameters.
Signed-off-by: NSong, Yoong Siang <yoong.siang.song@intel.com>
Signed-off-by: NVoon Weifeng <weifeng.voon@intel.com>
Signed-off-by: NOng Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current implementation of stmmac_stop_all_queues() and
stmmac_start_all_queues() will not work correctly when the value of
tx_queues_to_use is changed through ethtool -L DEVNAME rx N tx M command.

Also, netif_tx_start|stop_all_queues() are only needed in driver open()
and close() only.

Fixes: c22a3f48 net: stmmac: adding multiple napi mechanism
Signed-off-by: NOng Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: NVoon Weifeng <weifeng.voon@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

netif_set_real_num_tx_queues() & netif_set_real_num_rx_queues() should be
used to inform network stack about the real Tx & Rx queue (active) number
in both stmmac_open() and stmmac_resume(), therefore, we move the code
from stmmac_dvr_probe() to stmmac_hw_setup().

Fixes: c02b7a91 net: stmmac: use netif_set_real_num_{rx,tx}_queues
Signed-off-by: NAashish Verma <aashishx.verma@intel.com>
Signed-off-by: NOng Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Restructure NAPI add and delete process so that we can call them
accordingly in open() and ethtool_set_channels() accordingly.

Introduced stmmac_reinit_queues() to handle the transition needed
for changing Rx & Tx channels accordingly.
Signed-off-by: NOng Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We found the following warning when using W=1 to build kernel:

drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:3634:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
int ret, coe = priv->hw->rx_csum;

When digging stmmac_get_rx_header_len(), dwmac4_get_rx_header_len() and
dwxgmac2_get_rx_header_len() return 0 only, without any error code to
report. Therefore, it's better to define get_rx_header_len() as void.
Signed-off-by: NLuo Jiaxing <luojiaxing@huawei.com>
Reviewed-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Because clk_prepare_enable() and clk_disable_unprepare() already checked
NULL clock parameter, so the additional checks are unnecessary, just
remove them.
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NZhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

When WoL is enabled and the machine is powered off, the PHY remains
waiting for wakeup events at max speed, which is a waste of energy.

Slow down the PHY speed before stopping the ethernet if WoL is enabled,
Signed-off-by: NJisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the stmmac driver WOL implementation relies on MAC's PMT
feature. We have a case: the MAC HW doesn't enable PMT, instead, we
rely on the phy to support WOL. Implement the support for this case.
Signed-off-by: NJisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is to prepare WOL support with phy. Compared with WOL
implementation which relies on the MAC's PMT features, in phy
supported WOL case, device_may_wakeup() may also be true, but we
should not call mac's pmt() function if HW doesn't enable PMT.

And during resume, we should call phylink_start() if PMT is disabled.
Signed-off-by: NJisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For rx filter 'HWTSTAMP_FILTER_PTP_V2_EVENT', it should be
PTP v2/802.AS1, any layer, any kind of event packet, but HW only
take timestamp snapshot for below PTP message: sync, Pdelay_req,
Pdelay_resp.

Then it causes below issue when test E2E case:
ptp4l[2479.534]: port 1: received DELAY_REQ without timestamp
ptp4l[2481.423]: port 1: received DELAY_REQ without timestamp
ptp4l[2481.758]: port 1: received DELAY_REQ without timestamp
ptp4l[2483.524]: port 1: received DELAY_REQ without timestamp
ptp4l[2484.233]: port 1: received DELAY_REQ without timestamp
ptp4l[2485.750]: port 1: received DELAY_REQ without timestamp
ptp4l[2486.888]: port 1: received DELAY_REQ without timestamp
ptp4l[2487.265]: port 1: received DELAY_REQ without timestamp
ptp4l[2487.316]: port 1: received DELAY_REQ without timestamp

Timestamp snapshot dependency on register bits in received path:
SNAPTYPSEL TSMSTRENA TSEVNTENA 	PTP_Messages
01         x         0          SYNC, Follow_Up, Delay_Req,
                                Delay_Resp, Pdelay_Req, Pdelay_Resp,
                                Pdelay_Resp_Follow_Up
01         0         1          SYNC, Pdelay_Req, Pdelay_Resp

For dwmac v5.10a, enabling all events by setting register
DWC_EQOS_TIME_STAMPING[SNAPTYPSEL] to 2’b01, clearing bit [TSEVNTENA]
to 0’b0, which can support all required events.
Signed-off-by: NFugang Duan <fugang.duan@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 14b41a29 ("net: stmmac: Delete txtimer in suspend") was the
first attempt to fix a race between mod_timer() and setup_timer()
during stmmac_resume(). However the issue still exists as the commit
only addressed half of the issue.

Same race can still happen as stmmac_resume() re-attaches interface
way too early - even before hardware is fully initialized.  Worse,
doing so allows network traffic to restart and stmmac_tx_timer_arm()
being called in the middle of stmmac_resume(), which re-init tx timers
in stmmac_init_coalesce().  timer_list will be corrupted and system
crashes as a result of race between mod_timer() and setup_timer().

  systemd--1995    2.... 552950018us : stmmac_suspend: 4994
  ksoftirq-9       0..s2 553123133us : stmmac_tx_timer_arm: 2276
  systemd--1995    0.... 553127896us : stmmac_resume: 5101
  systemd--320     7...2 553132752us : stmmac_tx_timer_arm: 2276
  (sd-exec-1999    5...2 553135204us : stmmac_tx_timer_arm: 2276
  ---------------------------------
  pc : run_timer_softirq+0x468/0x5e0
  lr : run_timer_softirq+0x570/0x5e0
  Call trace:
   run_timer_softirq+0x468/0x5e0
   __do_softirq+0x124/0x398
   irq_exit+0xd8/0xe0
   __handle_domain_irq+0x6c/0xc0
   gic_handle_irq+0x60/0xb0
   el1_irq+0xb8/0x180
   arch_cpu_idle+0x38/0x230
   default_idle_call+0x24/0x3c
   do_idle+0x1e0/0x2b8
   cpu_startup_entry+0x28/0x48
   secondary_start_kernel+0x1b4/0x208

Fix this by deferring netif_device_attach() to the end of
stmmac_resume().
Signed-off-by: NLeon Yu <leoyu@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There's no caller in-tree since
commit 2af6106a ("net: stmmac: Introducing support for Page Pool")
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The paranoidal pointer check in IRQ handler looks very strange - it
really protects us only against bogus drivers which request IRQ line
with null pointer dev_id. However, the code fragment is incorrect
because the dev pointer is used before the actual check which leads
to undefined behavior. Remove the check to avoid confusing people
with incorrect code.
Signed-off-by: NMaxim Petrov <mmrmaximuzz@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Unfortunately sometimes ->probe() may fail. The commit b9663b7c
("net: stmmac: Enable SERDES power up/down sequence")
messed up with error handling and thus:

[   12.811311] ------------[ cut here ]------------
[   12.811993] kernel BUG at net/core/dev.c:9937!

Fix this by properly crafted error path.

Fixes: b9663b7c ("net: stmmac: Enable SERDES power up/down sequence")
Cc: Voon Weifeng <weifeng.voon@intel.com>
Cc: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Unfortunately sometimes ->probe() may fail. The commit b9663b7c
("net: stmmac: Enable SERDES power up/down sequence")
messed up with error handling and thus:

[   12.811311] ------------[ cut here ]------------
[   12.811993] kernel BUG at net/core/dev.c:9937!

Fix this by properly crafted error path.

Fixes: b9663b7c ("net: stmmac: Enable SERDES power up/down sequence")
Cc: Voon Weifeng <weifeng.voon@intel.com>
Cc: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is to enable Intel SERDES power up/down sequence. The SERDES
converts 8/10 bits data to SGMII signal. Below is an example of
HW configuration for SGMII mode. The SERDES is located in the PHY IF
in the diagram below.

<-----------------GBE Controller---------->|<--External PHY chip-->
+----------+         +----+            +---+           +----------+
|   EQoS   | <-GMII->| DW | < ------ > |PHY| <-SGMII-> | External |
|   MAC    |         |xPCS|            |IF |           | PHY      |
+----------+         +----+            +---+           +----------+
       ^               ^                 ^                ^
       |               |                 |                |
       +---------------------MDIO-------------------------+

PHY IF configuration and status registers are accessible through
mdio address 0x15 which is defined as mdio_adhoc_addr. During D0,
The driver will need to power up PHY IF by changing the power state
to P0. Likewise, for D3, the driver sets PHY IF power state to P3.
Signed-off-by: NVoon Weifeng <weifeng.voon@intel.com>
Signed-off-by: NOng Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If we don't have any filters available we can't rely upon the return
code of stmmac_add_hw_vlan_rx_fltr() / stmmac_del_hw_vlan_rx_fltr(). Add
a check for this.

Fixes: ed64639b ("net: stmmac: Add support for VLAN Rx filtering")
Signed-off-by: NJose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for VLAN ID-based filtering by the MAC controller for MAC
drivers that support it. Only the 12-bit VID field is used.
Signed-off-by: NChuah Kim Tatt <kim.tatt.chuah@intel.com>
Signed-off-by: NOng Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: NWong Vee Khee <vee.khee.wong@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add XLGMII support for stmmac including the list of speeds and defines
for them.
Signed-off-by: NJose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds all the necessary logic so that stmmac can be used with Synopsys
DesignWare XPCS.
Signed-off-by: NJose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert the stmmac ethernet driver to use the finalised link parameters
in mac_link_up() rather than the parameters in mac_config().
Suggested-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NJose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When CONFIG_OF is not enabled, of_fwnode_handle() will return NULL, even
though we can have a FW handle from a given device.

Fallback to dev_fwnode() helper if needed.
Signed-off-by: NJose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the linkmode_and()/linkmode_andnot() helpers to simplify the code.
Signed-off-by: NJose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Propagate the resolved link parameters via the mac_link_up() call for
MACs that do not automatically track their PCS state. We propagate the
link parameters via function arguments so that inappropriate members
of struct phylink_link_state can't be accessed, and creating a new
structure just for this adds needless complexity to the API.
Tested-by: NAndre Przywara <andre.przywara@arm.com>
Tested-by: NAlexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We cannot register the same netdev notifier multiple times when probing
stmmac devices. Register the notifier only once in module init, and also
make debugfs creation/deletion safe against simultaneous notifier call.

Fixes: 481a7d15 ("stmmac: debugfs entry name is not be changed when udev rename device name.")
Signed-off-by: NAaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Functions starting with __ usually indicate those which are exported,
but should not be called directly. Update some of those declared in the
API and make it more readable.

page_pool_unmap_page() and page_pool_release_page() were doing
exactly the same thing calling __page_pool_clean_page().  Let's
rename __page_pool_clean_page() to page_pool_release_page() and
export it in order to show up on perf logs and get rid of
page_pool_unmap_page().

Finally rename __page_pool_put_page() to page_pool_put_page() since we
can now directly call it from drivers and rename the existing
page_pool_put_page() to page_pool_put_full_page() since they do the same
thing but the latter is trying to sync the full DMA area.

This patch also updates netsec, mvneta and stmmac drivers which use
those functions.
Suggested-by: NJonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: NToke Høiland-Jørgensen <toke@redhat.com>
Acked-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NIlias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When running v5.5 with a rootfs on NFS, memory abort may happen in
the system resume stage:
 Unable to handle kernel paging request at virtual address dead00000000012a
 [dead00000000012a] address between user and kernel address ranges
 pc : run_timer_softirq+0x334/0x3d8
 lr : run_timer_softirq+0x244/0x3d8
 x1 : ffff800011cafe80 x0 : dead000000000122
 Call trace:
  run_timer_softirq+0x334/0x3d8
  efi_header_end+0x114/0x234
  irq_exit+0xd0/0xd8
  __handle_domain_irq+0x60/0xb0
  gic_handle_irq+0x58/0xa8
  el1_irq+0xb8/0x180
  arch_cpu_idle+0x10/0x18
  do_idle+0x1d8/0x2b0
  cpu_startup_entry+0x24/0x40
  secondary_start_kernel+0x1b4/0x208
 Code: f9000693 a9400660 f9000020 b4000040 (f9000401)
 ---[ end trace bb83ceeb4c482071 ]---
 Kernel panic - not syncing: Fatal exception in interrupt
 SMP: stopping secondary CPUs
 SMP: failed to stop secondary CPUs 2-3
 Kernel Offset: disabled
 CPU features: 0x00002,2300aa30
 Memory Limit: none
 ---[ end Kernel panic - not syncing: Fatal exception in interrupt ]---

It's found that stmmac_xmit() and stmmac_resume() sometimes might
run concurrently, possibly resulting in a race condition between
mod_timer() and setup_timer(), being called by stmmac_xmit() and
stmmac_resume() respectively.

Since the resume() runs setup_timer() every time, it'd be safer to
have del_timer_sync() in the suspend() as the counterpart.
Signed-off-by: NNicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

snps databook noted that physical coding sublayer (PCS) interface
that can be used when the MAC is configured for the TBI, RTBI, or
SGMII PHY interface. we have RGMII and SGMII in a SoC and it also
has the PCS block. it needs stmmac_init_phy and stmmac_mdio_register
function for initializing phy when it used RGMII interface.
Signed-off-by: NDejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds more information regarding HW Capabilities in the corresponding
DebugFS file.

Changes from v2:
- Remove the TX/RX queues in use (Jakub)
Signed-off-by: NJose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Adds the support for ETF scheduler using TBS feature which is available
in XGMAC and QoS IPs.

Changes from v2:
- Fix checkpatch issues (Jakub)
- Use the TBS bitfield
Signed-off-by: NJose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Adds the initial hooks for TBS support. This needs a 32 byte descriptor
in order for it to work with current HW. Adds all the logic for Enhanced
Descriptors in main core but no HW related logic for now.

Changes from v2:
- Use bitfield for TBS status / support (Jakub)
- Remove unneeded cache alignment (Jakub)
- Fix checkpatch issues
Signed-off-by: NJose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Add one notifier for udev changes net device name.
Fixes: b6601323ef9e ("net: stmmac: debugfs entry name is not be changed when udev rename")
Signed-off-by: NJiping Ma <jiping.ma2@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that we have the EST code for XGMAC and QoS we can use it with the
TAPRIO scheduler. Integrate it into the main driver and use the API to
configure the EST feature.
Signed-off-by: NJose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When we have pending packets we re-arm the TX timer with a magic value.

This changes the re-arm of the timer from 10us to the user-defined
coalesce value. As we support different speeds, having a magic value of
10us can be either too short or to large depending on the speed so we
let user configure it. The default value of the timer is 1ms but it can
be reconfigured by ethtool.

Changes from v1:
- Reword commit message (Jakub)
Signed-off-by: NJose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>