Start phylink instance and resume back the PHY to supply
RX clock to MAC before MAC layer initialization by calling
.stmmac_hw_setup(), since DMA reset depends on the RX clock,
otherwise DMA reset cost maximum timeout value then finally
timeout.

Fixes: 74371272 ("net: stmmac: Convert to phylink and remove phylib logic")
Signed-off-by: NFugang Duan <fugang.duan@nxp.com>
Signed-off-by: NJoakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current timeout value is not enough for gmac5 dma reset
on imx8mp platform, increase the timeout range.
Signed-off-by: NFugang Duan <fugang.duan@nxp.com>
Signed-off-by: NJoakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The m250_sel mux clock uses bit 4 in the PRG_ETH0 register. Fix this by
shifting the PRG_ETH0_CLK_M250_SEL_MASK accordingly as the "mask" in
struct clk_mux expects the mask relative to the "shift" field in the
same struct.

While here, get rid of the PRG_ETH0_CLK_M250_SEL_SHIFT macro and use
__ffs() to determine it from the existing PRG_ETH0_CLK_M250_SEL_MASK
macro.

Fixes: 566e8251 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: NJerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20201205213207.519341-1-martin.blumenstingl@googlemail.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

Commit 75792624 ("net: stmmac: add flexible PPS to dwmac
4.10a") was intended to modify the struct dwmac410_ops, but it got
somehow badly merged and modified the struct dwmac4_ops.

Revert the modification in struct dwmac4_ops and re-apply it
properly in struct dwmac410_ops.

Fixes: 75792624 ("net: stmmac: add flexible PPS to dwmac 4.10a")
Signed-off-by: NAntonio Borneo <antonio.borneo@st.com>
Reported-by: NAhmad Fatoum <a.fatoum@pengutronix.de>
Link: https://lore.kernel.org/r/20201124223729.886992-1-antonio.borneo@st.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

Fix an issue where dump stack is printed on suspend resume flow due to
netif_set_real_num_rx_queues() is not called with rtnl_lock held().

Fixes: 686cff3d ("net: stmmac: Fix incorrect location to set real_num_rx|tx_queues")
Reported-by: NChristophe ROULLIER <christophe.roullier@st.com>
Tested-by: NChristophe ROULLIER <christophe.roullier@st.com>
Cc: Alexandre TORGUE <alexandre.torgue@st.com>
Reviewed-by: NOng Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: NWong Vee Khee <vee.khee.wong@intel.com>
Link: https://lore.kernel.org/r/20201115074210.23605-1-vee.khee.wong@intel.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.

Fixes: 9efc9b2b ("net: stmmac: Add dwmac-intel-plat for GBE driver")
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NZhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1605249243-17262-1-git-send-email-zhangchangzhong@huawei.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

If the phy enables power saving technology, the dwmac's software reset
needs more time to complete, enlarge dma reset timeout to 200000us.
Signed-off-by: NJisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20201113090902.5c7aab1a@xhacker.debianSigned-off-by: NJakub Kicinski <kuba@kernel.org>

Commit 0366f7e0 ("net: stmmac: add ethtool support for get/set
channels") refactored channel initialization, but during that operation,
the spinlock initialization got lost. Fix this. This fixes the following
lockdep warning:

meson8b-dwmac ff3f0000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 1 PID: 331 Comm: kworker/1:2H Not tainted 5.9.0-rc3+ #1858
Hardware name: Hardkernel ODROID-N2 (DT)
Workqueue: kblockd blk_mq_run_work_fn
Call trace:
 dump_backtrace+0x0/0x1d0
 show_stack+0x14/0x20
 dump_stack+0xe8/0x154
 register_lock_class+0x58c/0x590
 __lock_acquire+0x7c/0x1790
 lock_acquire+0xf4/0x440
 _raw_spin_lock_irqsave+0x80/0xb0
 stmmac_tx_timer+0x4c/0xb0 [stmmac]
 call_timer_fn+0xc4/0x3e8
 run_timer_softirq+0x2b8/0x6c0
 efi_header_end+0x114/0x5f8
 irq_exit+0x104/0x110
 __handle_domain_irq+0x60/0xb8
 gic_handle_irq+0x58/0xb0
 el1_irq+0xbc/0x180
 _raw_spin_unlock_irqrestore+0x48/0x90
 mmc_blk_rw_wait+0x70/0x160
 mmc_blk_mq_issue_rq+0x510/0x830
 mmc_mq_queue_rq+0x13c/0x278
 blk_mq_dispatch_rq_list+0x2a0/0x698
 __blk_mq_do_dispatch_sched+0x254/0x288
 __blk_mq_sched_dispatch_requests+0x190/0x1d8
 blk_mq_sched_dispatch_requests+0x34/0x70
 __blk_mq_run_hw_queue+0xcc/0x148
 blk_mq_run_work_fn+0x20/0x28
 process_one_work+0x2a8/0x718
 worker_thread+0x48/0x460
 kthread+0x134/0x160
 ret_from_fork+0x10/0x1c

Fixes: 0366f7e0 ("net: stmmac: add ethtool support for get/set channels")
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20201029185011.4749-1-m.szyprowski@samsung.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

The commit "stmmac: intel: Adding ref clock 1us tic for LPI cntr"
introduced a regression which leads to the kernel panic duing loading
of the dwmac_intel module.

Move the code block after pci resources is obtained.

Fixes: b4c5f83a ("stmmac: intel: Adding ref clock 1us tic for LPI cntr")
Cc: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: NWong Vee Khee <vee.khee.wong@intel.com>
Link: https://lore.kernel.org/r/20201029093228.1741-1-vee.khee.wong@intel.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

Ethtool manual stated that the tx-timer is the "the amount of time the
device should stay in idle mode prior to asserting its Tx LPI". The
previous implementation for "ethtool --set-eee tx-timer" sets the LPI TW
timer duration which is not correct. Hence, this patch fixes the
"ethtool --set-eee tx-timer" to configure the EEE LPI timer.

The LPI TW Timer will be using the defined default value instead of
"ethtool --set-eee tx-timer" which follows the EEE LS timer implementation.

Changelog V2
*Not removing/modifying the eee_timer.
*EEE LPI timer can be configured through ethtool and also the eee_timer
module param.
*EEE TW Timer will be configured with default value only, not able to be
configured through ethtool or module param. This follows the implementation
of the EEE LS Timer.

Fixes: d765955d ("stmmac: add the Energy Efficient Ethernet support")
Signed-off-by: NVineetha G. Jaya Kumaran <vineetha.g.jaya.kumaran@intel.com>
Signed-off-by: NVoon Weifeng <weifeng.voon@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding reference clock (1us tic) for all LPI timer on Intel platforms.
The reference clock is derived from ptp clk. This also enables all LPI
counter.
Signed-off-by: NRusaimi Amira Ruslan <rusaimi.amira.rusaimi@intel.com>
Signed-off-by: NVoon Weifeng <weifeng.voon@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While unloading the dwmac-intel driver, clk_disable_unprepare() is
being called twice in stmmac_dvr_remove() and
intel_eth_pci_remove(). This causes kernel panic on the second call.

Removing the second call of clk_disable_unprepare() in
intel_eth_pci_remove().

Fixes: 09f012e6 ("stmmac: intel: Fix clock handling on error and remove paths")
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: NVoon Weifeng <weifeng.voon@intel.com>
Signed-off-by: NWong Vee Khee <vee.khee.wong@intel.com>
Reviewed-by: NAndy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add option in plat_stmmacenet_data struct to enable VLAN Filter Fail
Queuing. This option allows packets that fail VLAN filter to be routed
to a specific Rx queue when Receive All is also set.

When this option is enabled:
- Enable VFFQ only when entering promiscuous mode, because Receive All
  will pass up all rx packets that failed address filtering (similar to
  promiscuous mode).
- VLAN-promiscuous mode is never entered to allow rx packet to fail VLAN
  filters and get routed to selected VFFQ Rx queue.
Reviewed-by: NVoon Weifeng <weifeng.voon@intel.com>
Reviewed-by: NOng Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: NChuah, Kim Tatt <kim.tatt.chuah@intel.com>
Signed-off-by: NOng Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As part of the W=1 cleanups for ethernet, a million [*] driver
comments had to be cleaned up to get the W=1 compilation to
succeed. This change finally makes the drivers/net/ethernet tree
compile with W=1 set on the command line. NOTE: The kernel uses
kdoc style (see Documentation/process/kernel-doc.rst) when
documenting code, not doxygen or other styles.

After this patch the x86_64 build has no warnings from W=1, however
scripts/kernel-doc says there are 1545 more warnings in source files, that
I need to develop a script to fix in a followup patch.

The errors fixed here are all kdoc of a few classes, with a few outliers:
In file included from drivers/net/ethernet/qlogic/netxen/netxen_nic_hw.c:10:
drivers/net/ethernet/qlogic/netxen/netxen_nic.h:1193:18: warning: ‘FW_DUMP_LEVELS’ defined but not used [-Wunused-const-variable=]
 1193 | static const u32 FW_DUMP_LEVELS[] = { 0x3, 0x7, 0xf, 0x1f, 0x3f, 0x7f, 0xff };
      |                  ^~~~~~~~~~~~~~
... repeats 4 times...
drivers/net/ethernet/sun/cassini.c:2084:24: warning: suggest braces around empty body in an ‘else’ statement [-Wempty-body]
 2084 |    RX_USED_ADD(page, i);
drivers/net/ethernet/natsemi/ns83820.c: In function ‘phy_intr’:
drivers/net/ethernet/natsemi/ns83820.c:603:6: warning: variable ‘tbisr’ set but not used [-Wunused-but-set-variable]
  603 |  u32 tbisr, tanar, tanlpar;
      |      ^~~~~
drivers/net/ethernet/natsemi/ns83820.c: In function ‘ns83820_get_link_ksettings’:
drivers/net/ethernet/natsemi/ns83820.c:1207:11: warning: variable ‘tanar’ set but not used [-Wunused-but-set-variable]
 1207 |  u32 cfg, tanar, tbicr;
      |           ^~~~~
drivers/net/ethernet/packetengines/yellowfin.c:1063:18: warning: variable ‘yf_size’ set but not used [-Wunused-but-set-variable]
 1063 |   int data_size, yf_size;
      |                  ^~~~~~~

Normal kdoc fixes:
warning: Function parameter or member 'x' not described in 'y'
warning: Excess function parameter 'x' description in 'y'
warning: Cannot understand <string> on line <NNN> - I thought it was a doc line

[*] - ok it wasn't quite a million, but it felt like it.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

EEE should be only be enabled during stmmac_mac_link_up() when the
link are up and being set up properly. set_eee should only do settings
configuration and disabling the eee.

Without this fix, turning on EEE using ethtool will return
"Operation not supported". This is due to the driver is in a dead loop
waiting for eee to be advertised in the for eee to be activated but the
driver will only configure the EEE advertisement after the eee is
activated.

Ethtool should only return "Operation not supported" if there is no EEE
capbility in the MAC controller.

Fixes: 8a7493e5 ("net: stmmac: Fix a race in EEE enable callback")
Signed-off-by: NVoon Weifeng <weifeng.voon@intel.com>
Acked-by: NMark Gross <mgross@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch add support to --show-ring & --set-ring Ethtool functions:
- Adding min, max, power of two check to new ring parameter's value.
- Bring down the network interface before changing the value of ring
  parameters.
- Bring up the network interface after changing the value of ring
  parameters.
Signed-off-by: NSong, Yoong Siang <yoong.siang.song@intel.com>
Signed-off-by: NVoon Weifeng <weifeng.voon@intel.com>
Signed-off-by: NOng Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current implementation of stmmac_stop_all_queues() and
stmmac_start_all_queues() will not work correctly when the value of
tx_queues_to_use is changed through ethtool -L DEVNAME rx N tx M command.

Also, netif_tx_start|stop_all_queues() are only needed in driver open()
and close() only.

Fixes: c22a3f48 net: stmmac: adding multiple napi mechanism
Signed-off-by: NOng Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: NVoon Weifeng <weifeng.voon@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

netif_set_real_num_tx_queues() & netif_set_real_num_rx_queues() should be
used to inform network stack about the real Tx & Rx queue (active) number
in both stmmac_open() and stmmac_resume(), therefore, we move the code
from stmmac_dvr_probe() to stmmac_hw_setup().

Fixes: c02b7a91 net: stmmac: use netif_set_real_num_{rx,tx}_queues
Signed-off-by: NAashish Verma <aashishx.verma@intel.com>
Signed-off-by: NOng Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Restructure NAPI add and delete process so that we can call them
accordingly in open() and ethtool_set_channels() accordingly.

Introduced stmmac_reinit_queues() to handle the transition needed
for changing Rx & Tx channels accordingly.
Signed-off-by: NOng Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We found the following warning when using W=1 to build kernel:

drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:3634:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
int ret, coe = priv->hw->rx_csum;

When digging stmmac_get_rx_header_len(), dwmac4_get_rx_header_len() and
dwxgmac2_get_rx_header_len() return 0 only, without any error code to
report. Therefore, it's better to define get_rx_header_len() as void.
Signed-off-by: NLuo Jiaxing <luojiaxing@huawei.com>
Reviewed-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Because clk_prepare_enable() and clk_disable_unprepare() already checked
NULL clock parameter, so the additional checks are unnecessary, just
remove them.
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NZhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Because clk_prepare_enable() and clk_disable_unprepare() already checked
NULL clock parameter, so the additional checks are unnecessary, just
remove them.
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NZhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Because clk_prepare_enable() and clk_disable_unprepare() already checked
NULL clock parameter, so the additional checks are unnecessary, just
remove them.
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NZhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Create drivers/net/pcs and move the Synopsys DesignWare XPCS into the
new directory. Move the header file into a subdirectory
include/linux/pcs

Start a naming convention of all PCS files use the prefix pcs-, and
rename the XPCS files to fit.

v2:
Add include/linux/pcs

v4:
Fix include path in stmmac.
Remove PCS_DEVICES to avoid new prompts

Cc: Jose Abreu <Jose.Abreu@synopsys.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add dwmac-intel-plat to enable the stmmac driver in Intel Keem Bay.
Also add fix_mac_speed and tx_clk in order to change link speeds.
This is required as mac_speed_o is not connected in the
Intel Keem Bay SoC.
Signed-off-by: NRusaimi Amira Ruslan <rusaimi.amira.rusaimi@intel.com>
Signed-off-by: NVineetha G. Jaya Kumaran <vineetha.g.jaya.kumaran@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.

[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-throughSigned-off-by: NGustavo A. R. Silva <gustavoars@kernel.org>

The IPQ806x does not appear to have a functional multicast ethernet
address filter. This was observed as a failure to correctly receive IPv6
packets on a LAN to the all stations address. Checking the vendor driver
shows that it does not attempt to enable the multicast filter and
instead falls back to receiving all multicast packets, internally
setting ALLMULTI.

Use the new fallback support in the dwmac1000 driver to correctly
achieve the same with the mainline IPQ806x driver. Confirmed to fix IPv6
functionality on an RB3011 router.

Cc: stable@vger.kernel.org
Signed-off-by: NJonathan McDowell <noodles@earth.li>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If we don't have a hardware multicast filter available then instead of
silently failing to listen for the requested ethernet broadcast
addresses fall back to receiving all multicast packets, in a similar
fashion to other drivers with no multicast filter.

Cc: stable@vger.kernel.org
Signed-off-by: NJonathan McDowell <noodles@earth.li>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With the latest net-next tree, if test suspend/resume after enabling
WOL, we get error as below:

[  487.086365] dpm_run_callback(): mdio_bus_suspend+0x0/0x30 returns -16
[  487.086375] PM: Device stmmac-0:00 failed to suspend: error -16

-16 means -EBUSY, this is because I didn't enable wakeup of the correct
device when implementing phy based WOL feature. To be honest, I caught
the issue when implementing phy based WOL and then fix it locally, but
forgot to amend the phy based wol patch. Today, I found the issue by
testing net-next tree.
Signed-off-by: NJisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When WoL is enabled and the machine is powered off, the PHY remains
waiting for wakeup events at max speed, which is a waste of energy.

Slow down the PHY speed before stopping the ethernet if WoL is enabled,
Signed-off-by: NJisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the stmmac driver WOL implementation relies on MAC's PMT
feature. We have a case: the MAC HW doesn't enable PMT, instead, we
rely on the phy to support WOL. Implement the support for this case.
Signed-off-by: NJisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is to prepare WOL support with phy. Compared with WOL
implementation which relies on the MAC's PMT features, in phy
supported WOL case, device_may_wakeup() may also be true, but we
should not call mac's pmt() function if HW doesn't enable PMT.

And during resume, we should call phylink_start() if PMT is disabled.
Signed-off-by: NJisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If !device_can_wakeup(), there's no need to futher check. And return
-EOPNOTSUPP rather than -EINVAL if !device_can_wakeup().
Signed-off-by: NJisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove WAKE_MAGIC from supported modes if the HW capability register
shows no support for pmt_magic_frame.
Signed-off-by: NJisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simplify meson8b_init_rgmii_tx_clk() by using struct clk_parent_data to
initialize the clock parents. No functional changes intended.
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Amlogic Meson G12A, G12B and SM1 have the same (at least as far as we
know at the time of writing) PRG_ETHERNET glue register implementation.
This implementation however is slightly different from AXG as it now has
an undocument "auto cali idx val" register in PRG_ETH1[17:16] which
seems to be related to RGMII Ethernet.

Add a new compatible string for G12A SoCs so the logic for this new
register can be implemented in the future.
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.

This code was detected with the help of Coccinelle and, audited and
fixed manually.
Signed-off-by: NGustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit 84af7a61 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.

This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.

There are a variety of indentation styles found.

  a) 4 spaces + '---help---'
  b) 7 spaces + '---help---'
  c) 8 spaces + '---help---'
  d) 1 space + 1 tab + '---help---'
  e) 1 tab + '---help---'    (correct indentation)
  f) 1 tab + 1 space + '---help---'
  g) 1 tab + 2 spaces + '---help---'

In order to convert all of them to 1 tab + 'help', I ran the
following commend:

  $ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: NMasahiro Yamada <masahiroy@kernel.org>

The code is return PTR_ERR(NULL) which is zero or success.  We should
return -ENOMEM instead.

Fixes: 94abdad6 ("net: ethernet: dwmac: add ethernet glue logic for NXP imx8 chip")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NFugang Duan <fugang.duan@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NXP imx8 family like imx8mp/imx8dxl chips support Synopsys MAC 5.10a IP.
This patch adds settings for NXP imx8 glue layer:
- clocks
- dwmac address width
- phy interface mode selection
- adjust rgmii txclk rate

v2:
- adjust code sequences in order to have reverse christmas
  tree local variable ordering.
Signed-off-by: NFugang Duan <fugang.duan@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>