As the port speeds grow, the current value of "unlimited shaper",
200000000Kbps, might become lower than the actually supported speeds. Bump
it to the maximum value that fits in the corresponding QEEC field, which is
about 2.1Tbps.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The QEEC register configures scheduling elements. One of the bits of
configuration is the burst size to use for the shaper installed on the
element. Add the necessary fields to support this configuration.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the trap IDs and trap group used to report tunnel drops. Register
tunnel packet traps and associated tunnel trap group with devlink
during driver initialization.
Signed-off-by: NAmit Cohen <amitc@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This register configures the actions that are done during IPinIP
decapsulation based on the ECN bits.
Signed-off-by: NAmit Cohen <amitc@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This register performs mapping from overlay ECN to underlay ECN during
IPinIP encapsulation.
Signed-off-by: NAmit Cohen <amitc@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add QPDP. This register controls the port default Switch Priority and
Color. The default Switch Priority and Color are used for frames where the
trust state uses default values. Currently there are two cases where this
applies: a port is in trust-PCP state, but a packet arrives untagged; and a
port is in trust-DSCP state, but a non-IP packet arrives.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, VRRP packets and packets that hit exceptions during routing
(e.g., MTU error) are policed using the same policer towards the CPU.
This means, for example, that misconfiguration of the MTU on a routed
interface can prevent VRRP packets from reaching the CPU, which in turn
can cause the VRRP daemon to assume it is the Master router.

Fix this by using a dedicated policer for VRRP packets.

Fixes: 11566d34 ("mlxsw: spectrum: Add VRRP traps")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reported-by: NAlex Veber <alexve@mellanox.com>
Tested-by: NAlex Veber <alexve@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These enums want to be named MLXSW_REG_QEEC_HIERARCHY_, but due to a typo
lack the second H. That is confusing and complicates searching.

But actually the enumerators should be named _HR_, because that is how
their enum type is called. So rename them as appropriate.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the trap IDs and trap group used to report layer 3 drops. Register
layer 3 packet traps and associated layer 3 trap group with devlink
during driver initialization.
Signed-off-by: NAmit Cohen <amitc@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PMTM allows query or configuration of module types.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NShalom Toledo <shalomt@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The tx/rx lane fields got extended to 4 bits, update the reg field
description accordingly.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NShalom Toledo <shalomt@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In new firmware versions this register is extended with a sampling rate
for Spectrum-2 and future ASICs.

Increase the size of the register to ensure the field is initialized to
0 which means every packet is mirrored.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Provide a macro for getting QSFP module EEPROM page number from the
optional upper page number row offset, specified in request.
Signed-off-by: NVadim Pasternak <vadimp@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

Extend speed support with 400Gbps
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extend MGPIR - Management General Peripheral Information Register
with new field "num_of_modules" exposing the number of modules
supported by specific system.
Signed-off-by: NVadim Pasternak <vadimp@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 275e928f ("mlxsw: spectrum: Prevent force of 56G") prevented
the driver from setting a speed of 56G when auto-negotiation is off.
This is the only speed supported by mlxsw that cannot be set when
auto-negotiation is off, which makes it difficult to write generic
tests.

Further, the speed is not supported by newer ASICs such as Spectrum-2
and to the best of our knowledge it is not used by current users.

Therefore, remove 56G support from mlxsw.
Signed-off-by: NAmit Cohen <amitc@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Discard trap groups are defined in a different enum so that they could
all share the same policer ID: MLXSW_REG_HTGT_TRAP_GROUP_MAX + 1.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Subsequent patches will add discard traps support in mlxsw. The driver
cannot configure such traps with a normal trap action, but needs to use
exception trap action, which also increments an error counter.

On the other hand, when these traps are initialized or set to drop
action, they should use the default drop action set by the firmware.
This guarantees that when the feature is disabled we get the exact same
behavior as before the feature was introduced.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The QPSC allows advanced configuration of the PTP shapers.
Signed-off-by: NShalom Toledo <shalomt@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PTP Shaper field is used for enabling and disabling of port-rate based
shaper which is slightly lower than port rate.
Signed-off-by: NShalom Toledo <shalomt@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When configured, the Spectrum hardware can recognize PTP packets and
trap them to the CPU using dedicated traps, PTP0 and PTP1.

One reason to get PTP packets under dedicated traps is to have a
separate policer suitable for the amount of PTP traffic expected when
switch is operated as a boundary clock. For this, add two new trap
groups, MLXSW_REG_HTGT_TRAP_GROUP_SP_PTP0 and _PTP1, and associate the
two PTP traps with these two groups.

In the driver, specifically for Spectrum-1, event PTP packets will need
to be paired up with their timestamps. Those arrive through a different
set of traps, added later in the patch set. To support this future use,
introduce a new PTP op, ptp_receive.

It is possible to configure which PTP messages should be trapped under
which PTP trap. On Spectrum systems, we will use PTP0 for event
packets (which need timestamping), and PTP1 for control packets (which
do not). Thus configure PTP0 trap with a custom callback that defers to
the ptp_receive op.

Additionally, L2 PTP packets are actually trapped through the LLDP trap,
not through any of the PTP traps. So treat the LLDP trap the same way as
the PTP0 trap. Unlike PTP traps, which are currently still disabled,
LLDP trap is active. Correspondingly, have all the implementations of
the ptp_receive op return true, which the handler treats as a signal to
forward the packet immediately.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This register serves to configure global parameters of certain
monitoring operations. The following patches will use it to configure
that when PTP timestamps are delivered through the PTP FIFO traps, the
FIFO in question is cleared as well.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MTPPTR is used for reading the per port PTP timestamp FIFO.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This register is used for configuring under which trap to deliver PTP
packets depending on type of the packet.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This register serves for configuration of which PTP messages should be
timestamped. This is a global configuration, despite the register name.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extend macros MLXSW_REG_MTMP_TEMP_TO_MC() to allow support of negative
temperature readout, since chip and others thermal components are
capable of operating within the negative temperature.
With no such support negative temperature will be consider as very high
temperature and it will cause wrong readout and thermal shutdown.
For negative values 2`s complement is used.
Tested in chamber.
Example of chip ambient temperature readout with chamber temperature:
-10 Celsius:
temp1:             -6.0C  (highest =  -5.0C)
-5 Celsius:
temp1:             -1.0C  (highest =  -1.0C)

v2 (Andrew Lunn):
* Replace '%u' with '%d' in mlxsw_hwmon_module_temp_show()
Signed-off-by: NVadim Pasternak <vadimp@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MTPPS register provides the device PPS capabilities, configure the PPS
in and out modules and holds the PPS in time stamp.
Signed-off-by: NShalom Toledo <shalomt@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MTUTC register configures the HW UTC counter.
Signed-off-by: NShalom Toledo <shalomt@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When PVID is removed from a bridge port, the Linux bridge drops both
untagged and prio-tagged packets. Align mlxsw with this behavior.

Fixes: 148f472d ("mlxsw: reg: Add the Switch Port Acceptable Frame Types register")
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extend sensor index size for Management Temperature Bulk Register
(MTBR) and Management Temperature Register (MTMP) upto 12 bits in
order to align registers description with new version of PRM document.
Add define for base sensor index for SFP modules temperature reading
for MTMP register.
Signed-off-by: NVadim Pasternak <vadimp@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add MGPIR - Management General Peripheral Information Register, which
allows software to query the hardware and firmware general information
of peripheral entities as Gearboxes etc.
Signed-off-by: NVadim Pasternak <vadimp@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extend the size of sensor_index field of MTMP (Management Temperature
Register), from 8 to 12 bits due to hardware change.
Add define for sensor index for Gear Box (inter-connects) temperature
reading.
Signed-off-by: NVadim Pasternak <vadimp@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PPLR register allows configuration of the port's loopback mode.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add MGIR register. MGIR, Management General Information Register, allows
software to query the hardware and firmware general information.
Signed-off-by: NShalom Toledo <shalomt@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PTYS register introduces a new layout for port type-speed fields. These
fields extend the existing ones in order to handle more types and speeds.
For example, the new 200Gbps speed.
Signed-off-by: NShalom Toledo <shalomt@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

80 columns wrapping change in mlxsw_reg_ptys_eth_unpack function.
Signed-off-by: NShalom Toledo <shalomt@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rename p_eth_proto_adm to p_eth_proto_admin in mlxsw_reg_ptys_eth_unpack
function.
Signed-off-by: NShalom Toledo <shalomt@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of deriving the port connector type from port admin state, query it
from firmware.
Signed-off-by: NShalom Toledo <shalomt@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove eth_proto_lp_advertise field in PTYS register since it is not
supported by the firmware.
Signed-off-by: NShalom Toledo <shalomt@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add FORE (Fan Out of Range Event Register), which is used for fan fault
reading.
Signed-off-by: NVadim Pasternak <vadimp@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>