- 06 7月, 2011 2 次提交
-
-
由 Yoshihiro Shimoda 提交于
If the driver didn't set this parameter on the ETHER, the CPU will encounter the "data address error" exception. Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yoshihiro Shimoda 提交于
When link was down, the bit of DM in ECMR was always set. So, we could not use half-duplex mode on the controller. Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 31 3月, 2011 1 次提交
-
-
由 Lucas De Marchi 提交于
Fixes generated by 'codespell' and manually reviewed. Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>
-
- 15 3月, 2011 6 次提交
-
-
由 Yoshihiro Shimoda 提交于
The SH7757's ETHER and GETHER use common MDIO pin. The MDIO pin is selected by specific register. So this patch adds new interface in bb_info, and when the sh_eth driver use the mdio, the register can be changed by the function. Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yoshihiro Shimoda 提交于
The SH7757 have GETHER and ETHER both. This patch supports them. Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yoshihiro Shimoda 提交于
The previous code had hardcoded the PHY_INTERFACE_MODE_MII of phy_connect. So some Gigabit PHYs will not behave correctly. The patch adds the phy_interface in sh_eth_plat_data, so we can select the phy interface. Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yoshihiro Shimoda 提交于
The SH7763 has GETHER. So the specification of some registers differs than other CPUs. This patch removes almost #ifdef of CONFIG_CPU_SUBTYPE_SH7763. Then we are able to add other CPU's GETHER easily. Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yoshihiro Shimoda 提交于
The defination is hardcoded in this driver for some CPUs. This patch modifies to get resource of TSU address from platform_device. Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yoshihiro Shimoda 提交于
The previous code cannot handle the ETHER and GETHER both as same time because the definitions of register was hardcoded. Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 23 2月, 2011 1 次提交
-
-
由 Nobuhiro Iwamatsu 提交于
This commit supports following functions. - get_settings - set_settings - nway_reset - get_msglevel - set_msglevel - get_link - get_strings - get_ethtool_stats - get_sset_count About other function, the device does not support. Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 12 12月, 2010 1 次提交
-
-
由 Tejun Heo 提交于
janz-ican3, sh_eth, skge and vxge don't use workqueue at all and there is no reason to flush the system_wq. Drop flush_scheduled_work() calls and references to workqueue. Signed-off-by: NTejun Heo <tj@kernel.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: Stephen Hemminger <shemminger@linux-foundation.org> Cc: Ramkrishna Vepa <ramkrishna.vepa@exar.com> Cc: Sivakumar Subramani <sivakumar.subramani@exar.com> Cc: Sreenivasa Honnur <sreenivasa.honnur@exar.com> Cc: Jon Mason <jon.mason@exar.com> Cc: netdev@vger.kernel.org
-
- 16 11月, 2010 1 次提交
-
-
由 Paul Mundt 提交于
sh_eth is the last in-tree user of the ctrl_xxx I/O routines. This simply converts them over to regular MMIO accesors. Signed-off-by: NPaul Mundt <lethal@linux-sh.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 03 9月, 2010 1 次提交
-
-
由 Eric Dumazet 提交于
fresh skbs have ip_summed set to CHECKSUM_NONE (0) We can avoid setting again skb->ip_summed to CHECKSUM_NONE in drivers. Introduce skb_checksum_none_assert() helper so that we keep this assertion documented in driver sources. Change most occurrences of : skb->ip_summed = CHECKSUM_NONE; by : skb_checksum_none_assert(skb); Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 26 8月, 2010 1 次提交
-
-
由 Joe Perches 提交于
"foo = &function" is more commonly written "foo = function" Done with coccinelle script: // <smpl> @r@ identifier f; @@ f(...) { ... } @@ identifier r.f; @@ - &f + f // </smpl> drivers/net/tehuti.c used a function and struct with the same name, the function was renamed. Compile tested x86 only. Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 19 8月, 2010 1 次提交
-
-
由 Kuninori Morimoto 提交于
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 04 8月, 2010 1 次提交
-
-
由 Stefan Weil 提交于
Cc: Jiri Kosina <trivial@kernel.org> Cc: linux-kernel@vger.kernel.org Signed-off-by: NStefan Weil <weil@mail.berlios.de> Signed-off-by: NJiri Kosina <jkosina@suse.cz>
-
- 19 7月, 2010 1 次提交
-
-
由 Richard Cochran 提交于
The phy_mii_ioctl() function unnecessarily throws away the original ifreq. We need access to the ifreq in order to support PHYs that can perform hardware time stamping. Two maverick drivers filter the ioctl commands passed to phy_mii_ioctl(). This is unnecessary since phylib will check the command in any case. Signed-off-by: NRichard Cochran <richard.cochran@omicron.at> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 08 7月, 2010 1 次提交
-
-
由 Yoshihiro Shimoda 提交于
The SH7757 has 2 Fast Ethernet controller (ETHER) and 2 Gigabit Ethernet Controller (GETHER). This patch supports 2 ETHER only. Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 21 5月, 2010 1 次提交
-
-
由 Denis Kirjanov 提交于
Allocated memory for IRQs should be freed when releasing the mii_bus Signed-off-by: NDenis Kirjanov <dkirjanov@kernel.org> Acked-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 10 5月, 2010 1 次提交
-
-
由 Eric Dumazet 提交于
Now that core network takes care of trans_start updates, dont do it in drivers themselves, if possible. Drivers can avoid one cache miss (on dev->trans_start) in their start_xmit() handler. Exceptions are NETIF_F_LLTX drivers Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 30 3月, 2010 1 次提交
-
-
由 Tejun Heo 提交于
include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h percpu.h is included by sched.h and module.h and thus ends up being included when building most .c files. percpu.h includes slab.h which in turn includes gfp.h making everything defined by the two files universally available and complicating inclusion dependencies. percpu.h -> slab.h dependency is about to be removed. Prepare for this change by updating users of gfp and slab facilities include those headers directly instead of assuming availability. As this conversion needs to touch large number of source files, the following script is used as the basis of conversion. http://userweb.kernel.org/~tj/misc/slabh-sweep.py The script does the followings. * Scan files for gfp and slab usages and update includes such that only the necessary includes are there. ie. if only gfp is used, gfp.h, if slab is used, slab.h. * When the script inserts a new include, it looks at the include blocks and try to put the new include such that its order conforms to its surrounding. It's put in the include block which contains core kernel includes, in the same order that the rest are ordered - alphabetical, Christmas tree, rev-Xmas-tree or at the end if there doesn't seem to be any matching order. * If the script can't find a place to put a new include (mostly because the file doesn't have fitting include block), it prints out an error message indicating which .h file needs to be added to the file. The conversion was done in the following steps. 1. The initial automatic conversion of all .c files updated slightly over 4000 files, deleting around 700 includes and adding ~480 gfp.h and ~3000 slab.h inclusions. The script emitted errors for ~400 files. 2. Each error was manually checked. Some didn't need the inclusion, some needed manual addition while adding it to implementation .h or embedding .c file was more appropriate for others. This step added inclusions to around 150 files. 3. The script was run again and the output was compared to the edits from #2 to make sure no file was left behind. 4. Several build tests were done and a couple of problems were fixed. e.g. lib/decompress_*.c used malloc/free() wrappers around slab APIs requiring slab.h to be added manually. 5. The script was run on all .h files but without automatically editing them as sprinkling gfp.h and slab.h inclusions around .h files could easily lead to inclusion dependency hell. Most gfp.h inclusion directives were ignored as stuff from gfp.h was usually wildly available and often used in preprocessor macros. Each slab.h inclusion directive was examined and added manually as necessary. 6. percpu.h was updated not to include slab.h. 7. Build test were done on the following configurations and failures were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my distributed build env didn't work with gcov compiles) and a few more options had to be turned off depending on archs to make things build (like ipr on powerpc/64 which failed due to missing writeq). * x86 and x86_64 UP and SMP allmodconfig and a custom test config. * powerpc and powerpc64 SMP allmodconfig * sparc and sparc64 SMP allmodconfig * ia64 SMP allmodconfig * s390 SMP allmodconfig * alpha SMP allmodconfig * um on x86_64 SMP allmodconfig 8. percpu.h modifications were reverted so that it could be applied as a separate patch and serve as bisection point. Given the fact that I had only a couple of failures from tests on step 6, I'm fairly confident about the coverage of this conversion patch. If there is a breakage, it's likely to be something in one of the arch headers which should be easily discoverable easily on most builds of the specific arch. Signed-off-by: NTejun Heo <tj@kernel.org> Guess-its-ok-by: NChristoph Lameter <cl@linux-foundation.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
-
- 04 1月, 2010 1 次提交
-
-
由 roel kluin 提交于
If no break occurred, cnt reaches 0 after the loop. Signed-off-by: NRoel Kluin <roel.kluin@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 30 12月, 2009 1 次提交
-
-
由 H Hartley Sweeten 提交于
Use the %pM kernel extension to display the MAC address. Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 16 12月, 2009 1 次提交
-
-
由 Magnus Damm 提交于
Fix sh_eth for sh7724 by adding NET_IP_ALIGN support V2. Without this patch the receive data is misaligned. Signed-off-by: NMagnus Damm <damm@opensource.se> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 19 11月, 2009 1 次提交
-
-
由 Joe Perches 提交于
Not as fancy as coccinelle. Checkpatch errors ignored. Compile tested allyesconfig x86, not all files compiled. grep -rPl --include=*.[ch] "\brequest_irq\s*\([^,\)]+,\s*\&" drivers/net | while read file ; do \ perl -i -e 'local $/; while (<>) { s@(\brequest_irq\s*\([^,\)]+,\s*)\&@\1@g ; print ; }' $file ;\ done Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 27 10月, 2009 1 次提交
-
-
由 Nobuhiro Iwamatsu 提交于
Add include asm/cacheflush.h, because declaration of __flush_purge_region moved to asm/cacheflush.h. Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 13 10月, 2009 2 次提交
-
-
由 Magnus Damm 提交于
Add Runtime PM support to the sh_eth driver. The clock to the ethernet hardware block will be enabled as long as the network device is up. Signed-off-by: NMagnus Damm <damm@opensource.se> Tested-by: NKuninori Morimoto <morimoto.kuninori@renesas.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Magnus Damm 提交于
Extend the sh_eth driver to allow passing the mac address using the platform data structure. This to simplify board setup code. Signed-off-by: NMagnus Damm <damm@opensource.se> Tested-by: NKuninori Morimoto <morimoto.kuninori@renesas.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 29 8月, 2009 1 次提交
-
-
由 Yoshihiro Shimoda 提交于
The method of ETHER_LINK pin is board dependence. This patch adding paramters are: - no_ether_link : If set to 1, do not use ETHER_LINK - ether_link_active_low : If set to 1, ETHER_LINK is active low. Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 06 7月, 2009 1 次提交
-
-
由 Patrick McHardy 提交于
This patch is the result of an automatic spatch transformation to convert all ndo_start_xmit() return values of 0 to NETDEV_TX_OK. Some occurences are missed by the automatic conversion, those will be handled in a seperate patch. Signed-off-by: NPatrick McHardy <kaber@trash.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 26 6月, 2009 1 次提交
-
-
由 roel kluin 提交于
Unsigned boguscnt cannot be less than 0. Signed-off-by: NRoel Kluin <roel.kluin@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 13 6月, 2009 1 次提交
-
-
由 Patrick McHardy 提交于
Convert magic values 1 and -1 to NETDEV_TX_BUSY and NETDEV_TX_LOCKED respectively. 0 (NETDEV_TX_OK) is not changed to keep the noise down, except in very few cases where its in direct proximity to one of the other values. Signed-off-by: NPatrick McHardy <kaber@trash.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 27 5月, 2009 1 次提交
-
-
由 David S. Miller 提交于
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 26 5月, 2009 5 次提交
-
-
由 Yoshihiro Shimoda 提交于
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yoshihiro Shimoda 提交于
This improves readability by collecting CPU dependency code. Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yoshihiro Shimoda 提交于
Fix the problem that this driver not update rxdesc in sh_eth_rx. Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yoshihiro Shimoda 提交于
Fix the probrem that TX/RX descirptor not set physical memory. Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yoshihiro Shimoda 提交于
Fix the problem that may not work receive process by cache coherency issue. Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 14 4月, 2009 1 次提交
-
-
由 Alexander Beregalov 提交于
Signed-off-by: NAlexander Beregalov <a.beregalov@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 19 3月, 2009 1 次提交
-
-
由 Nobuhiro Iwamatsu 提交于
Handling of IRQ of the SH7763/SH7764 CPU which sh_eth supported was changed. This revises it for this change. Signed-off-by: NNobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-