There is no point in implementing a detect callback for the LTC4215
and LTC4245, as these devices can't be detected. It was there solely
to handle "force" module parameters to instantiate devices, but now
we have a better sysfs interface that can do the same.

So we can get rid of the ugly module parameters and the detect
callbacks. This shrinks the binary module sizes by 36% and 46%,
respectively.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Ira W. Snyder <iws@ovro.caltech.edu>

[akpm@linux-foundation.org: fix KVM]
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Acked-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When power is applied to the ltc4245 chip it sometimes reports spurious
faults, which are exposed as alarms in the hwmon output. Clear the fault
register when the driver is installed to clear the alarms.
Signed-off-by: NIra W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

When power is applied to the ltc4215 chip it sometimes reports spurious
faults. The faults are not yet exposed via sysfs, however it may be useful
for userspace to read the fault register directly with the i2cget command.
Clear the fault register when the driver is installed so userspace doesn't
have to worry about spurious fault indications.
Signed-off-by: NIra W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Add Lynnfield processor support. Lynnfield is a quad-core Nehalem
based microprocessor for Desktop market, which is introduced in
September 2009.
Signed-off-by: NHuaxu Wan <huaxu.wan@linux.intel.com>
Signed-off-by: NKent Liu <kent.liu@linux.intel.com>
Acked-by: NRudolf Marek <r.marek@assembler.cz>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Following patch adds support for mobile Penryn CPUs. Intel documents this
poorly. I asked the Coretemp author for some help. This is totally untested and
may not work. Please test!
Signed-off-by: NRudolf Marek <r.marek@assembler.cz>
Cc: Huaxu Wan <huaxu.wan@linux.intel.com>
Cc: Kent Liu <kent.liu@linux.intel.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Fix Atom CPUs support. Intel documents TjMax at 90 degrees C but
some Atoms may have 125 degrees C (this is undocumented speculation).
Signed-off-by: NRudolf Marek <r.marek@assembler.cz>
Cc: Huaxu Wan <huaxu.wan@linux.intel.com>
Cc: Kent Liu <kent.liu@linux.intel.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

The legacy fscpos and fscher drivers have been replaced by the unified
fschmd driver. The transition period is over now, we can delete them.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NHans de Goede <hdegoede@redhat.com>

The ADM1030/ADM1031 chips have temperature offset registers, for both the
local and remote temperature sensors. Following the example set forth in
the LM90/ADM1032 driver, expose the offset registers to userspace.
Signed-off-by: NIra W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

This makes it consistent with other buses (platform, i2c, vio, ...).  I'm
not sure why we use the prefixes, but there must be a reason.

This was easy enough to do it, and I did it.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Samuel Ortiz <sameo@openedhand.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Acked-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make the code a little bit nicer, and shorter.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kaiwan N Billimoria <kaiwan@designergraphix.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make the code a little bit nicer, and shorter.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Cc: Marc Pignat <marc.pignat@hevs.ch>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NMarc Pignat <marc.pignat@hevs.ch>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The static code scanner "Parfait" reported this because pwm_config is
only 3 bytes - pwm_config[3] is out of range.

Since this code path is never called with ix == 3 (the device has no PWM4
output) this doesn't change anything in practice.  But to encourage
testing with Parfait, lets make the warning go away...
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

On resume from suspend, the driver currently resets the logical state as
if it was brought up from halt.  This patch uses the
dev_pm_ops.resume/restore methods to synchronize the hardware with the
memorized logical state, in effect bringing back the accelerometer and
backlight to the state prior to suspend.  Works for both suspend to ram
and hibernation.  The patch has zero effect on the running state.
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If already requested, gpio_data and irq should be freed in the case of an
error.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NJonathan Cameron <jic23@cam.ac.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Occasionally it is helpful to be able to turn a temperature sensor off
(for example if it's making unwanted electrical noise).  This patch
adds a sysfs node to put any adm1021 compatible device into low power mode.
Signed-off-by: NMichael Abbott <michael.abbott@diamond.ac.uk>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The ADM1023 temperature sensor supports higher resolution for its external
sensor (sensitivity of 1/8 deg C).  This patch makes this higher
resolution available through the appropriate temperature sysfs nodes.

Curiously, this functionality was available in the 2.4 kernel driver (but
formatted in a less helpful manner).

Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: NMichael Abbott <michael.abbott@diamond.ac.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Acked-by: NPavel Machek <pavel@ucw.cz>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This enabled power management functions for the SPI transport layer of the
lis3 devices.  The device's suspend mode is only entered in case no wakeup
threshold has been given.  In this case, the device is supposed to wake up
the system and must thus not be put to deep sleep.

[randy.dunlap@oracle.com: fix lis3-spi for CONFIG_PM=n]
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Acked-by: NPavel Machek <pavel@ucw.cz>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This offers a way for platforms to define flags and thresholds for the
free-fall/wakeup functions of the lis302d chips.

More registers needed to be seperated as they are specific to the
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Acked-by: NPavel Machek <pavel@ucw.cz>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Enable the coretemp driver on an Intel Atom.

I'm not sure if the readings are correct, however - on my 330, the driver
reports values between 27 and 41 °C (with core1 being about 8°C hotter
than core0, given the same load).  Maybe the maximum temperature of 100 °C
is wrong for Atom CPUs.

Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This driver adds support for the hardware monitoring features of
the WM831x PMICs to the hwmon API. Monitoring is provided for
the system voltages supported natively by the WM831x, the chip
temperature, the battery temperature and the auxiliary inputs
of the WM831x.

Currently no alarms are supported, though digital comparators on
the WM831x devices would allow these to be provided.

Since the auxiliary and battery temperature input scaling depends
on the system configuration the value is reported as a voltage to
userspace.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This driver provides reporting of the status supply voltage rails
of the WM835x series of PMICs via the hwmon API.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The Winbond/Nuvoton WPCD377I is the reduced version of a Super-I/O
which emulates the National Semiconductor LM96000 hardware monitoring
chips, but without the hardware monitoring part. Instead of plain
disabling the emulation, the vendor left the emulated chip visible,
but all monitored values are always zero. This is rather confusing for
the users. So detect this case and refuse to bind to such fake chips.

This fixes lm-sensors ticket #2182:
http://www.lm-sensors.org/ticket/2182Signed-off-by: NJean Delvare <khali@linux-fr.org>

Now that we have ACPI-based hardware monitoring drivers, and we will
start telling users to use them instead of native drivers when I/O
resources conflict, I think it would be good to clearly mark ACPI
drivers as such in Kconfig.

Also, in the case of monolithic kernels, I think the ACPI drivers
should take precedence over native drivers, so they should be listed
first in Makefile.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Luca Tettamanti <kronos.it@gmail.com>

Use the function resource_size, which reduces the chance of introducing
off-by-one errors in calculating the resource size.

The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
struct resource *res;
@@

- (res->end - res->start) + 1
+ resource_size(res)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Drivers should be including <linux/io.h> instead of <asm/io.h>.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Alistair John Strachan <alistair@devzero.co.uk>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: Juerg Haefliger <juergh@gmail.com>
Cc: Frank Seidel <frank@f-seidel.de>
Acked-by: NJim Cromie <jim.cromie@gmail.com>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Roger Lucas <vt8231@hiddenengine.co.uk>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Add support for Texas Instruments TMP421/422/423 temperature sensor IC.

TI's TMP421/422/423 are I2C temperature sensor chips. These chips are
similar to TI's TMP401/411 chips, but with reduced functionality (only
temperature measurement). The chips have one local sensor and up to
three (TMP423) remote sensors.
Signed-off-by: NAndre Prendel <andre.prendel@gmx.de>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

We had a report about a mainboard for AMD family 0Fh processors not
routing the 6th VID pin from the CPU to the hardware monitoring chip.

While the vendor should have wired the pin (or, failing that, should
have hardwired it to level high rather than low), the fact is that
none of these processors are currently known to operate at the lower
voltage levels which require the 6th VID pin. So, as a practical
workaround, I propose to ignore the 6th VID pin for these CPUs.

If this decision ever causes problems, we'll reconsider.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Frank Myhr <fmyhr@fhmtech.com>
Tested-by: NHleb Valoshka <375gnu@gmail.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>

Most known Abit motherboards have unique uguru chip IDs. However,
some "refresh" boards keep the same chip ID but have a different
DMI string. As our DMI board string matching is (necessarily)
strict, some boards were failing DMI detection, and as the old
probe method was also failing, the driver would not load.

The only known boards affected by this problem are the IP35 Pro XE
(vs IP35 Pro) and the AB9 Pro (vs AB9). Is it not sufficient to
relax the match criteria, as some boards (e.g. the AB9 Quad GT)
have different uguru chip IDs.

This patch replaces the dmi_name string with a NULL terminated
array of strings to be matched per uguru chip ID. It has been
compile and runtime tested (thanks Rune).

References: https://bugs.launchpad.net/bugs/298798Signed-off-by: NAlistair John Strachan <alistair@devzero.co.uk>
Tested-by: NRune Svendsen <runesvend@gmail.com>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

On newer Asus boards the "upper" limit of a sensor is encoded as
delta from the "lower" limit. Fix the driver to correctly handle
this case.
Signed-off-by: NLuca Tettamanti <kronos.it@gmail.com>
Tested-by: NAlex Macfarlane Smith <nospam@archifishal.co.uk>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

The SMSC LPC47M233 and LPC47M292 chips have the same device ID but
are not compatible.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Juerg Haefliger <juergh@gmail.com>
Acked-by: NHans de Goede <hdegoede@redhat.com>

Add support for the ADC controller on the S3C series of processors to
drivers/hwmon for use with hardware monitoring systems.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Switch the AB9, AB9 QuadQT and IX38 QuadGT over from port
probing to the preferred DMI probe method.
Signed-off-by: NAlistair John Strachan <alistair@devzero.co.uk>
Tested-by: Ndan <dan@deeog.com>
Tested-by: NNygel Lyndley <nygel.lyndley@gmail.com>
Tested-by: NDmitriy Fedchenko <dmitriy-fedc@yandex.ru>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Add omitted update_lock to one switch/case in set_div.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Acked-by: NHans J. Koch <hjk@linutronix.de>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

The LIS302DL accelerometer chip has a 'click' feature which can be used to
detect sudden motion on any of the three axis.  Configuration data is
passed via spi platform_data and no action is taken if that's not
specified, so it won't harm any existing platform.

To make the configuration effective, the IRQ lines need to be set up
appropriately.  This patch also adds a way to do that from board support
code.

The DD_* definitions were factored out to an own enum because they are
specific to LIS3LV02D devices.
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Acked-by: NPavel Machek <pavel@ucw.cz>
Acked-by: NEric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Separate the 6710 and 6715, and set the right axis information for the
6715.
Reported-by: NIsaac702 <isaac702@gmail.com>

Add the 6930.
Reported-by: NChristian Weidle <slateroni@gmail.com>

Add the 2710.
Reported-by: NPavel Herrmann <morpheus.ibis@gmail.com>
Signed-off-by: NEric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Now that there is no need to hookup on the open/close of the joystick,
it's possible to use the simplified interface input_polled_device, instead
of creating our own kthread.

[randy.dunlap@oracle.com: fix Kconfig]
[randy.dunlap@oracle.com: fix Kconfig some more]
Signed-off-by: NEric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

After measurement on my laptop, it seems that turning off the device does
not bring any energy saving (within 0.1W precision).  So let's keep the
device always on.  It simplifies the code, and it avoids the problem of
reading a wrong value sometimes just after turning the device on.

Moreover, since commit ef2cfc79 had been
too zealous, the device was actually never turned off anyway.  This patch
also restores the damages done by this commit concerning the
initialisation/poweroff.

Also do more clean up with the usage of the lis3_dev global variable.
Signed-off-by: NEric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>