Some hwmon sysfs attributes have a length of 20 bytes (plus terminating 0).
I2C_NAME_SIZE is defined as 20 and thus can not be used to define the length
of hwmon sysfs attributes. Replace it with PMBUS_NAME_SIZE, set to 24.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: NRobert Coulson <robert.coulson@ericsson.com>

Add ADP4000, NCP4200 and NCP4208 to the list of devices supported by the generic
PMBus driver, and add device IDs to enable explicit instantiation.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: NRobert Coulson <robert.coulson@ericsson.com>
Acked-by: NJean Delvare <khali@linux-fr.org>

In VID mode, output voltages are measured and reported as VID values, and
have to be converted to voltages using VID conversion tables or functions.
Support is added for VR11 only at this time.

This patch enables support for PMBus devices supporting VID VR11 based output
voltage selection such as NCP4200 and NCP4208.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: NRobert Coulson <robert.coulson@ericsson.com>

Since the number of PMBus drivers is getting large, move them into
directory drivers/hwmon/pmbus to improve readability and scalability.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: NRobert Coulson <robert.coulson@ericsson.com>

This patch adds the core and pkg support to coretemp.
These thresholds can be configured via the sysfs interfaces tempX_max
and tempX_max_hyst. An interrupt is generated when CPU temperature reaches
or crosses above tempX_max OR drops below tempX_max_hyst.

This patch is based on the documentation in IA Manual vol 3A, that can be
downloaded from here:
http://download.intel.com/design/processor/manuals/253668.pdfSigned-off-by: NDurgadoss R <durgadoss.r@intel.com>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

LM95231 is fully compatible to LM95241; only necessary change is to add
chip detection.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Acked-by: NJean Delvare <khali@linux-fr.org>

A hwmon driver for the National Semiconductor LM95245 dual temperature
sensors chip.
Signed-off-by: NAlexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

Add support for Philips SA56004, an LM86 compatible temperature sensor.
Signed-off-by: NStijn Devriendt <sdevrien@cisco.com>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

Add support for NTC Thermistor series. In this release, the
following thermistors are supported: NCP15WB473, NCP18WB473, NCP03WB473,
and NCP15WL333. This driver is based on the datasheet of MURATA.

The driver in the patch does conversion from the raw ADC value
(either voltage or resistence) to temperature. In order to use
voltage values as input, the circuit schematics should be provided
with the platform data. A compensation table for each type of thermistor
is provided for the conversion.
Signed-off-by: NDonggeun Kim <dg77.kim@samsung.com>
Signed-off-by: NMyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: NKyungMin Park <kyungmin.park@samsung.com>
Reviewed-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

MAX1668 and compatibles have several external temperature sensors, but only a
single FAULT status bit. If a fault occurs, the temperature reported on the
affected sensors is 127 degrees C. Use this knowledge to report fault on
external sensors.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Acked-by: NJean Delvare <khali@linux-fr.org>

This patch adds support for MAX1668 and compatible temperature sensors.
Signed-off-by: NDavid George <david.george@ska.ac.za>
[guenter.roeck@ericsson.com: minor cleanup of probe error path]
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

spi_sync call uses its spi_message parameter to keep completion information,
using a drvdata structure is not thread-safe. Use a mutex to prevent
multiple access to shared driver data.
Signed-off-by: NPavel Herrmann <morpheus.ibis@gmail.com>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NPavel Machek <pavel@ucw.cz>
Acked-by: NMarek Vasut <marek.vasut@gmail.com>
Acked-by: NCyril Hrubis <metan@ucw.cz>
Tested-by: NStanislav Brabec <utx@penguin.cz>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org

A copy-and-paste error caused it87_attributes_vid to be referenced
where it87_attributes_label should be. Thankfully the group is only
used for attribute removal, not attribute creation, so the effects of
this bug are limited, but let's fix it still.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
Acked-by: NGuenter Roeck <guenter.roeck@ericsson.com>

The object returned by atk_gitm is dynamically allocated and must be
freed.
Signed-off-by: NLuca Tettamanti <kronos.it@gmail.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org

Coefficients to convert chip register values to voltage/current have been
slightly changed in revision B of the chip datasheet. Update driver coefficients
to match the coefficients in the datasheet.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Acked-by: NJean Delvare <khali@linux-fr.org>

Using integer variable types for register to data conversions can cause
overflows especially for power calculations, which are in microwatt.
Use long variables instead.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org # 2.6.39+

It is possible that a PMBus device supports the READ_TEMPERATURE2 and/or
READ_TEMPERATURE3 registers but does not support READ_TEMPERATURE1.
Improve temperature status register detection to address this condition.
Reported-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org # 2.6.39+

Negative temperatures were returned in degrees C instead of milli-Degrees C.
Also, negative temperatures were reported for remote temperature sensors even
if the chip was configured for positive-only results.

Fix by detecting temperature modes, and by treating negative temperatures
similar to positive temperatures, with appropriate sign extension.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org # 2.6.30+

The LM95241 driver accepts every chip ID equal to or larger than 0xA4 as its
own, and other chips such as LM95245 use chip IDs in the accepted ID range.
This results in false chip detection.

Fix problem by accepting only the known LM95241 chip ID.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org # 2.6.30+

It's Nehemiah, not Nemiah.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NGuenter Roeck <guenter.roeck@ericsson.com>

The F71869A is almost the same as the F71869F/E, except that it has
the normal number of temp and pwm zones for a F71882FG derived chip,
rather then the limited number of the F71869F/E.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Tested-by: NMax Baldwin <archerseven@gmail.com>
Acked-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Handle errors on 8-bit register reads and writes too. Also use likely
and unlikely to make the functions faster on success.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NGuenter Roeck <guenter.roeck@ericsson.com>

Additional temperature attribute support is easy to detect, so do it.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: NRobert Coulson <robert.coulson@ericsson.com>
Cc: stable.kernel.org # 2.6.39

Some PMBus devices return no error when reading fan speed registers, but don't
really support fans. Strengthen fan detection by also checking if fan
configuration registers exist.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: NRobert Coulson <robert.coulson@ericsson.com>
Cc: stable.kernel.org # 2.6.39

Probe function did not free allocated memory if it failed. Fix it.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: NRobert Coulson <robert.coulson@ericsson.com>

Some PMBus devices do not support the PMBus revision register, so don't check
if it exists.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: NRobert Coulson <robert.coulson@ericsson.com>
Cc: stable.kernel.org # 2.6.39

Initialize dynamically allocated sysfs attributes before device_create_file()
call to suppress lockdep_init_map() warning if lockdep debugging is enabled.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org # 2.6.34+

Initialize dynamically allocated sysfs attributes before device_create_file()
call to suppress lockdep_init_map() warning if lockdep debugging is enabled.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org # 2.6.34+

Initialize dynamically allocated sysfs attributes before device_create_file()
call to suppress lockdep_init_map() warning if lockdep debugging is enabled.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org # 2.6.34+

Call sysfs_attr_init() from atk_init_attribute() to handle sysfs attribute
initialization in a single function.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Cc: Luca Tettamanti <kronos.it@gmail.com>
Acked-by: NJean Delvare <khali@linux-fr.org>

pdev_entry.cpu and pdev_entry.cpu_core_id aren't used anywhere in the
driver code so we can drop these struct members.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

Improve detection of MAX6642 by reading non existing registers (0x04, 0x06
and 0xff). Reading those registers returns the previously read value.
Signed-off-by: NPer Dalen <per.dalen@appeartv.com>
[guenter.roeck@ericsson.com: added second set of register reads]
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

Further relax temperature range checks after reading the IA32_TEMPERATURE_TARGET
register. If the register returns a value other than 0 in bits 16..32, assume
that the returned value is correct.

This change applies to both packet and core temperature limits.

Cc: Carsten Emde <C.Emde@osadl.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Acked-by: NFenghua Yu <fenghua.yu@intel.com>

Commit a321cedb excludes CPU models 0xe, 0xf,
0x16, and 0x1a from TjMax temperature adjustment, even though several of those
CPUs are known to have TiMax other than 100 degrees C, and even though the code
in adjust_tjmax() explicitly handles those CPUs and points to a Web document
listing several of the affected CPU IDs.

Reinstate original TjMax adjustment if TjMax can not be determined using the
IA32_TEMPERATURE_TARGET register.

https://bugzilla.kernel.org/show_bug.cgi?id=32582Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Cc: Huaxu Wan <huaxu.wan@linux.intel.com>
Cc: Carsten Emde <C.Emde@osadl.org>
Cc: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Yong Wang <yong.y.wang@linux.intel.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Tested-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NFenghua Yu <fenghua.yu@intel.com>
Cc: <stable@kernel.org> # .35.x .36.x .37.x .38.x .39.x

The current temperature range check of MSR_IA32_TEMPERATURE_TARGET
seems too strict to me, some TjMax values documented in
Documentation/hwmon/coretemp wouldn't pass. Relax the check so that
all the documented values pass.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Carsten Emde <C.Emde@osadl.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

The temp_fault sysfs attribute is wrong, it should be temp2_fault instead.
Reported-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: NPer Dalen <per.dalen@appeartv.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

chk_ucode_version() is only called from coretemp_probe() which is
__devinit, so it can be marked __devinit too.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Durgadoss R <durgadoss.r@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

Initialize sysfs attrs before device_create_file() call to suppress
lockdep_init_map() warning:

WARNING: at kernel/lockdep.c:2701 lockdep_init_map+0x12d/0x140()
Reviewed-by: NRobert Coulson <robert.coulson@ericsson.com>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@kernel.org # .39.x

Update comments describing the handling of HT CPUs based on review feedback.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Acked-by: NJean Delvare <khali@linux-fr.org>