Some hwmon sysfs attributes have a length of 20 bytes (plus terminating 0).
I2C_NAME_SIZE is defined as 20 and thus can not be used to define the length
of hwmon sysfs attributes. Replace it with PMBUS_NAME_SIZE, set to 24.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: NRobert Coulson <robert.coulson@ericsson.com>

Add ADP4000, NCP4200 and NCP4208 to the list of devices supported by the generic
PMBus driver, and add device IDs to enable explicit instantiation.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: NRobert Coulson <robert.coulson@ericsson.com>
Acked-by: NJean Delvare <khali@linux-fr.org>

In VID mode, output voltages are measured and reported as VID values, and
have to be converted to voltages using VID conversion tables or functions.
Support is added for VR11 only at this time.

This patch enables support for PMBus devices supporting VID VR11 based output
voltage selection such as NCP4200 and NCP4208.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: NRobert Coulson <robert.coulson@ericsson.com>

Since the number of PMBus drivers is getting large, move them into
directory drivers/hwmon/pmbus to improve readability and scalability.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: NRobert Coulson <robert.coulson@ericsson.com>

This patch adds the core and pkg support to coretemp.
These thresholds can be configured via the sysfs interfaces tempX_max
and tempX_max_hyst. An interrupt is generated when CPU temperature reaches
or crosses above tempX_max OR drops below tempX_max_hyst.

This patch is based on the documentation in IA Manual vol 3A, that can be
downloaded from here:
http://download.intel.com/design/processor/manuals/253668.pdfSigned-off-by: NDurgadoss R <durgadoss.r@intel.com>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

LM95231 is fully compatible to LM95241; only necessary change is to add
chip detection.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Acked-by: NJean Delvare <khali@linux-fr.org>

A hwmon driver for the National Semiconductor LM95245 dual temperature
sensors chip.
Signed-off-by: NAlexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

Add support for Philips SA56004, an LM86 compatible temperature sensor.
Signed-off-by: NStijn Devriendt <sdevrien@cisco.com>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

Add support for NTC Thermistor series. In this release, the
following thermistors are supported: NCP15WB473, NCP18WB473, NCP03WB473,
and NCP15WL333. This driver is based on the datasheet of MURATA.

The driver in the patch does conversion from the raw ADC value
(either voltage or resistence) to temperature. In order to use
voltage values as input, the circuit schematics should be provided
with the platform data. A compensation table for each type of thermistor
is provided for the conversion.
Signed-off-by: NDonggeun Kim <dg77.kim@samsung.com>
Signed-off-by: NMyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: NKyungMin Park <kyungmin.park@samsung.com>
Reviewed-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

MAX1668 and compatibles have several external temperature sensors, but only a
single FAULT status bit. If a fault occurs, the temperature reported on the
affected sensors is 127 degrees C. Use this knowledge to report fault on
external sensors.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Acked-by: NJean Delvare <khali@linux-fr.org>

This patch adds support for MAX1668 and compatible temperature sensors.
Signed-off-by: NDavid George <david.george@ska.ac.za>
[guenter.roeck@ericsson.com: minor cleanup of probe error path]
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

Align unfenced buffers on older hardware to the power-of-two object
size.  The docs suggest that it should be possible to align only to a
power-of-two tile height, but using the already computed fence size is
easier and always correct. We also have to make sure that we unbind
misaligned buffers upon tiling changes.

In order to prevent a repetition of this bug, we change the interface
to the alignment computation routines to force the caller to provide
the requested alignment and size of the GTT binding rather than assume
the current values on the object.
Reported-and-tested-by: NSitosfe Wheeler <sitsofe@yahoo.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=36326Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NKeith Packard <keithp@keithp.com>

Kernel bugzilla: 39252
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 726b65ad ("tulip: Convert uses of KERN_DEBUG") enabled
some old previously inactive uses of pr_debug converted by
commit dde7c8ef ("tulip/dmfe.c: Use dev_<level> and pr_<level>").

Remove these pr_debugs.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While compiling it with Fedora 15, I noticed this issue:

  inlined from ‘si4713_write_econtrol_string’ at drivers/media/radio/si4713-i2c.c:1065:24:
  arch/x86/include/asm/uaccess_32.h:211:26: error: call to ‘copy_from_user_overflow’ declared with attribute error: copy_from_user() buffer size is not provably correct

Cc: stable@kernel.org
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: NSakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Acked-by: NEduardo Valentin <edubezval@gmail.com>
Reviewed-by: NEugene Teo <eugeneteo@kernel.sg>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

spi_sync call uses its spi_message parameter to keep completion information,
using a drvdata structure is not thread-safe. Use a mutex to prevent
multiple access to shared driver data.
Signed-off-by: NPavel Herrmann <morpheus.ibis@gmail.com>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NPavel Machek <pavel@ucw.cz>
Acked-by: NMarek Vasut <marek.vasut@gmail.com>
Acked-by: NCyril Hrubis <metan@ucw.cz>
Tested-by: NStanislav Brabec <utx@penguin.cz>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org

A copy-and-paste error caused it87_attributes_vid to be referenced
where it87_attributes_label should be. Thankfully the group is only
used for attribute removal, not attribute creation, so the effects of
this bug are limited, but let's fix it still.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
Acked-by: NGuenter Roeck <guenter.roeck@ericsson.com>

The object returned by atk_gitm is dynamically allocated and must be
freed.
Signed-off-by: NLuca Tettamanti <kronos.it@gmail.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org

hpwdt is a PCI driver so it should depend on PCI.
Fixes these build errors:

drivers/watchdog/hpwdt.c:762: error: implicit declaration of function 'pci_iomap'
drivers/watchdog/hpwdt.c:762: warning: assignment makes pointer from integer without a cast
drivers/watchdog/hpwdt.c:797: error: implicit declaration of function 'pci_iounmap'
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
Cc: Thomas Mingarelli <thomas.mingarelli@hp.com>

Remove Kconfig regression caused by commit
a4616153 "watchdog: hpwdt: build hpwdt as
module by default with NMI_DECODING enabled"

With the above change applied, hpwdt will be enabled unconditionally by just
entering the Watchdog subscreen in menuconfig. Since this driver is not
essential to boot any box it should remain disabled until it gets manually
enabled, just like all other drivers.
Signed-off-by: NOlaf Hering <olaf@aepfle.de>
Cc: Tony Camuso <tcamuso@redhat.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>

Only let the rx parser be enabled if it is necessary (if VLAN extraction,
IP or TCP checksumming or the rx queue filer are enabled). Otherwise
disable it.

The new routine gfar_check_rx_parser_mode should be run after every
change on this features and will enable/disable the parser as necessary.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NSebastian Poehn <sebastian.poehn@belden.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

When receiving the first RX interrupt before the internal call
to napi_schedule_prep is successful the RX interrupt gets disabled
and is never enabled again as the poll function never gets executed.
Signed-off-by: NMichael Thalmeier <Michael.Thalmeier@sigmatek.at>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Coefficients to convert chip register values to voltage/current have been
slightly changed in revision B of the chip datasheet. Update driver coefficients
to match the coefficients in the datasheet.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Acked-by: NJean Delvare <khali@linux-fr.org>

There is no software fallback implemented for SCTP or FCoE checksumming,
and so it should not be passed on by software devices like bridge or bonding.

For VLAN devices, this is different. First, the driver for underlying device
should be prepared to get offloaded packets even when the feature is disabled
(especially if it advertises it in vlan_features). Second, devices under
VLANs do not get replaced without tearing down the VLAN first.

This fixes a mess I accidentally introduced while converting bonding to
ndo_fix_features.

NETIF_F_SOFT_FEATURES are removed from BOND_VLAN_FEATURES because they
are unused as of commit 712ae51a.
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We've tried several times to make this machine 'just work', but every
patch that does causes many other machines to fail. This adds a quirk
which special cases this hardware and forces ssc to be
disabled. There's no way to override this from the command line; that
would be a significantly more invasive change.

This patch fixes #36656 on fdo bugzilla:
https://bugs.freedesktop.org/show_bug.cgi?id=36656Signed-off-by: NKeith Packard <keithp@keithp.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=36656Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

The firmware on some machine will report duplicated hardware error
source ID in HEST.  This is considered a firmware bug.  To provide
better warning message, this patch adds duplicated hardware error
source ID detecting and corresponding printk.

This patch fixes #37412 on kernel bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=37412

Reported-by: marconifabio@ubuntu-it.org
Signed-off-by: NHuang Ying <ying.huang@intel.com>
Tested-by: NMathias <janedo.spam@gmail.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

As Simon reported, digital TV broke with mt20xx tuner due to
commit ad020dc2.

The mt20xx tuner passes V4L2_TUNER_DIGITAL_TV to tuner core. However, the
check_mode code now doesn't handle it well. Change the logic there to
avoid the breakage, and fix a test for analog-only at g_tuner.
Reported-by: NSimon Arlott <simon@fire.lp0.eu>
Tested-by: NSimon Arlott <simon@fire.lp0.eu>
Cc: stable@kernel.org
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Attached is a patch which addresses a race condition in the DVB core
related to closing/reopening the DVB frontend device in quick
succession.  This is the reason that devices such as the HVR-1300,
HVR-3000, and HVR-4000 have been failing to scan properly under MythTV
and w_scan.

The gory details of the race are described in the patch.

Devin

There is a race condition exhibited when channel scanners such as w_scan and
MythTV quickly close and then reopen the frontend device node.

Under normal conditions, the behavior is as follows:

1.  Application closes the device node
2.  DVB frontend ioctl calls dvb_frontend_release which sets
    fepriv->release_jiffies
3.  DVB frontend thread *eventually* calls dvb_frontend_is_exiting() which
    compares fepriv->release_jiffies, and shuts down the thread if timeout has
    expired
4.  Thread goes away
5.  Application opens frontend device
6.  DVB frontend ioctl() calls ts_bus_ctrl(1)
7.  DVB frontend ioctl() creates new frontend thread, which calls
    dvb_frontend_init(), which has demod driver init() routine setup initial
    register state for demod chip.
8.  Tuning request is issued.

The race occurs when the application in step 5 performs the new open() call
before the frontend thread is shutdown.  In this case the ts_bus_ctrl() call
is made, which strobes the RESET pin on the demodulator, but the
dvb_frontend_init() function never gets called because the frontend thread
hasn't gone away yet.  As a result, the initial register config for the demod
is *never* setup, causing subsequent tuning requests to fail.

If there is time between the close and open (enough for the dvb frontend
thread to be torn down), then in that case the new frontend thread is created
and thus the dvb_frontend_init() function does get called.

The fix is to set the flag which forces reinitialization if we did in fact
call ts_bus_ctrl().

This problem has been seen on the HVR-1300, HVR-3000, and HVR-4000, and is
likely occuring on other designs as well where ts_bus_ctrl() actually strobes
the reset pin on the demodulator.

Note that this patch should supercede any patches submitted for the
1300/3000/4000 which remove the code that removes GPIO code in
cx8802_dvb_advise_acquire(), which have been circulating by users for some
time now...

Canonical tracking this issue in Launchpad 439163:

Thanks to Jon Sayers from Hauppauge and Florent Audebert from Anevia S.A. for
providing hardware to test/debug with.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Cc: Jon Sayers <j.sayers@hauppauge.co.uk>
Cc: Florent Audebert <florent.audebert@anevia.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

When CONFIG_SND is not enabled, radio-sf16fmr2 build fails with:

so make this driver depend on SND.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: linux-media@vger.kernel.org
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

On reading the ext_csd for the first time (in 1 bit mode), save the
ext_csd information needed for bus width compare.

On every pass we make re-reading the ext_csd, compare the data
against the saved ext_csd data.

This fixes a regression introduced in 3.0-rc1 by 08ee80cc
("mmc: core: eMMC bus width may not work on all platforms"), which
incorrectly assumed we would be re-reading the ext_csd at resume-
time.
Signed-off-by: NPhilip Rakity <prakity@marvell.com>
Tested-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

All ACPICA locks are allocated by the same function,
acpi_os_create_lock(), with the help of a local variable called
"lock".  Thus, when lockdep is enabled, it uses "lock" as the
name of all those locks and regards them as instances of the same
lock, which causes it to report possible locking problems with them
when there aren't any.

To work around this problem, define acpi_os_create_lock() as a macro
and make it pass its argument to spin_lock_init(), so that lockdep
uses it as the name of the new lock.  Define this macron in a
Linux-specific file, to minimize the resulting modifications of
the OS-independent ACPICA parts.

This change is based on an earlier patch from Andrea Righi and it
addresses a regression from 2.6.39 tracked as
https://bugzilla.kernel.org/show_bug.cgi?id=38152Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Reported-and-tested-by: NBorislav Petkov <bp@alien8.de>
Tested-by: NAndrea Righi <andrea@betterlinux.com>
Reviewed-by: NFlorian Mickler <florian@mickler.org>
Signed-off-by: NLen Brown <len.brown@intel.com>

Compute drivers may change this, so make sure to emit it to
avoid errors in bo blits.

Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=39119Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Konstantin Belousov found an error in the define of G4x_GMCH_SIZE_VT_2M
relative to the GMCH specs, and confirmed that indeed one of his users
with a Q45 reports 0xb not 0xc for a 2/2MiB GATT.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Konstantin Belousov <kostikbel@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

sound/isa/es18xx.c: In function ‘snd_es18xx_playback1_prepare’:
sound/isa/es18xx.c:501:9: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
sound/isa/es18xx.c: In function ‘snd_es18xx_playback_pointer’:
sound/isa/es18xx.c:818:3: error: implicit declaration of function ‘snd_dma_pointer’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[2]: *** [sound/isa/es18xx.o] Error 1
sound/isa/sscape.c: In function ‘upload_dma_data’:
sound/isa/sscape.c:481:3: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[2]: *** [sound/isa/sscape.o] Error 1
sound/isa/ad1816a/ad1816a_lib.c: In function ‘snd_ad1816a_playback_prepare’:
sound/isa/ad1816a/ad1816a_lib.c:244:2: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
sound/isa/ad1816a/ad1816a_lib.c: In function ‘snd_ad1816a_playback_pointer’:
sound/isa/ad1816a/ad1816a_lib.c:302:2: error: implicit declaration of function ‘snd_dma_pointer’ [-Werror=implicit-function-declaration]
sound/isa/ad1816a/ad1816a_lib.c: In function ‘snd_ad1816a_free’:
sound/isa/ad1816a/ad1816a_lib.c:544:3: error: implicit declaration of function ‘snd_dma_disable’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [sound/isa/ad1816a/ad1816a_lib.o] Error 1
make[3]: Target `__build' not remade because of errors.
make[2]: *** [sound/isa/ad1816a] Error 2
sound/isa/es1688/es1688_lib.c: In function ‘snd_es1688_playback_prepare’:
sound/isa/es1688/es1688_lib.c:417:2: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
sound/isa/es1688/es1688_lib.c: In function ‘snd_es1688_playback_pointer’:
sound/isa/es1688/es1688_lib.c:509:2: error: implicit declaration of function ‘snd_dma_pointer’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [sound/isa/es1688/es1688_lib.o] Error 1
make[3]: Target `__build' not remade because of errors.
make[2]: *** [sound/isa/es1688] Error 2
sound/isa/gus/gus_dma.c: In function ‘snd_gf1_dma_program’:
sound/isa/gus/gus_dma.c:79:2: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
sound/isa/gus/gus_dma.c: In function ‘snd_gf1_dma_done’:
sound/isa/gus/gus_dma.c:177:3: error: implicit declaration of function ‘snd_dma_disable’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [sound/isa/gus/gus_dma.o] Error 1
sound/isa/gus/gus_pcm.c: In function ‘snd_gf1_pcm_capture_prepare’:
sound/isa/gus/gus_pcm.c:591:2: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
sound/isa/gus/gus_pcm.c: In function ‘snd_gf1_pcm_capture_pointer’:
sound/isa/gus/gus_pcm.c:619:2: error: implicit declaration of function ‘snd_dma_pointer’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [sound/isa/gus/gus_pcm.o] Error 1
make[3]: Target `__build' not remade because of errors.
make[2]: *** [sound/isa/gus] Error 2
sound/isa/sb/sb16_csp.c: In function ‘snd_sb_csp_ioctl’:
sound/isa/sb/sb16_csp.c:228:227: error: case label does not reduce to an integer constant
make[3]: *** [sound/isa/sb/sb16_csp.o] Error 1
sound/isa/sb/sb16_main.c: In function ‘snd_sb16_playback_prepare’:
sound/isa/sb/sb16_main.c:276:2: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
sound/isa/sb/sb16_main.c: In function ‘snd_sb16_playback_pointer’:
sound/isa/sb/sb16_main.c:456:2: error: implicit declaration of function ‘snd_dma_pointer’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [sound/isa/sb/sb16_main.o] Error 1
sound/isa/sb/sb8_main.c: In function ‘snd_sb8_playback_prepare’:
sound/isa/sb/sb8_main.c:172:3: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
sound/isa/sb/sb8_main.c: In function ‘snd_sb8_playback_pointer’:
sound/isa/sb/sb8_main.c:425:2: error: implicit declaration of function ‘snd_dma_pointer’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [sound/isa/sb/sb8_main.o] Error 1
make[3]: Target `__build' not remade because of errors.
make[2]: *** [sound/isa/sb] Error 2
sound/isa/wss/wss_lib.c: In function ‘snd_wss_playback_prepare’:
sound/isa/wss/wss_lib.c:1025:2: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
sound/isa/wss/wss_lib.c: In function ‘snd_wss_playback_pointer’:
sound/isa/wss/wss_lib.c:1160:2: error: implicit declaration of function ‘snd_dma_pointer’ [-Werror=implicit-function-declaration]
sound/isa/wss/wss_lib.c: In function ‘snd_wss_free’:
sound/isa/wss/wss_lib.c:1695:3: error: implicit declaration of function ‘snd_dma_disable’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [sound/isa/wss/wss_lib.o] Error 1
warning: (RADIO_MIROPCM20) selects SND_ISA which has unmet direct dependencies (SOUND && !M68K && SND && ISA && ISA_DMA_API)

A build with ISA && ISA_DMA && !ISA_DMA_API results in:
  CC      sound/isa/es18xx.o
  CC      sound/isa/sscape.o
  CC      sound/isa/ad1816a/ad1816a_lib.o
  CC      sound/isa/es1688/es1688_lib.o
  CC      sound/isa/gus/gus_dma.o
  CC      sound/isa/gus/gus_pcm.o
  CC      sound/isa/sb/sb16_csp.o
  CC      sound/isa/sb/sb16_main.o
  CC      sound/isa/sb/sb8_main.o
  CC      sound/isa/wss/wss_lib.o

The root cause for this is hidden in this Kconfig warning:

Adding a dependency on ISA_DMA_API to RADIO_MIROPCM20 fixes these issues.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Acked-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

...which is measured by the size and not the amount of space remaining.

Waiting upon size-8, did one of two things. In the common case with more
than 8 bytes available to write into the ring, it would return
immediately. Otherwise, it would timeout given the impossible condition
of waiting for more space than is available in the ring, leading to
warnings such as:

[drm:intel_cleanup_ring_buffer] *ERROR* failed to quiesce render ring
whilst cleaning up: -16
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NKeith Packard <keithp@keithp.com>

This reverts commit a51f7a66.

We still have a few Ironlake and Sandybridge machines which fail when
RC6 is enabled. Better luck next release?
Signed-off-by: NKeith Packard <keithp@keithp.com>

i915_driver_load adds a write-combining MTRR region for the GTT
aperture to improve memory speeds through the aperture. If
i915_driver_load fails after this, it would not have cleaned up the
MTRR. This shouldn't cause any problems, except for consuming an MTRR
register. Still, it's best to clean up completely in the failure path,
which is easily done by calling mtrr_del if the mtrr was successfully
allocated.

i915_driver_load calls i915_gem_load which register
i915_gem_inactive_shrink. If i915_driver_load fails after calling
i915_gem_load, the shrinker will be left registered. When called, it
will access freed memory and crash. The fix is to unregister the shrinker in the
failure path using code duplicated from i915_driver_unload.

i915_driver_load also has some incorrect gotos in the error cleanup
paths:

 * After failing to initialize the GTT (which cannot happen, btw,
   intel_gtt_get returns a fixed (non-NULL) value), it tries to
   free the uninitialized WC IO mapping. Fixed this by changing the
   target from out_iomapfree to out_rmmap
Signed-off-by: NKeith Packard <keithp@keithp.com>
Tested-by: NLin Ming <ming.m.lin@intel.com>

Using integer variable types for register to data conversions can cause
overflows especially for power calculations, which are in microwatt.
Use long variables instead.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org # 2.6.39+

BUS_CNTL reg and bits moved between pre-PCIE and PCIE asics.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>