Prevent using uninitialized or negative index when handling
steering entries.

Fixes: b12d93d6 ('mlx4: Add support for promiscuous mode in the new steering model.')
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

zero_gid is not used, so remove this redundant array.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for receiving multicast/unicast traffic with
the don't trap rule.

Sniffing these packets requires a flow steering rule of type NORMAL
at priority 0 with flag IB_FLOW_ATTR_FLAGS_DONT_TRAP set.
Choosing between multicast or unicast is done via ethernet L2 dest_mac
mask and value:
- If mask is all zeros - unicast and multicast are set.
- If mask non zero - only mask with multicast bit 1 and rest 0 is
                     supported, the mac value will choose if it is
                     multicast or unicast rule.

If the mask multicast bit is on and some other bits are on too, it means
a request for specific multicast or unicast, this is not supported,
either receive all multicast or all unicast.

Only when limitations are met registered QP will receive requested type
but other QPs can receive same traffic if registered for it.
Otherwise, if limitations are not met, an error will be returned.

Limitations:
- Rule must be with priority 0.
- A0 mode is not supported.
- Sniffer QP cannot appear in any other flow steering rule.
Signed-off-by: NMarina Varshaver <marinav@mellanox.com>
Reviewed-by: NMatan Barak <matanb@mellanox.com>
Reviewed-by: NYishai Hadas <yishaih@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Both new_steering_entry() and existing_steering_entry() return values
based on their success or failure, but currently they fall through
silently.  This can make troubleshooting difficult, as we were unable
to tell which one of these two functions returned errors or
specifically what code was returned.  This patch remedies that
situation by passing the return codes to err, which is returned by
mlx4_qp_attach_common() itself.

This also addresses a leak in the call to mlx4_bitmap_free() as well.
Signed-off-by: NRobb Manes <rmanes@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When SRIOV commands are executed over the comm-channel and get
a fatal error (e.g. timeout, closing command failure) the VF enters
into error state and reset flow is activated.

To be able to recognize whether the failure was on a closing command, the
operational code for the given VHCR command is used. Once the device entered
into an error state we prevent redundant error messages from being printed.
Signed-off-by: NYishai Hadas <yishaih@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We activate reset flow upon command fatal errors, when the device enters an
erroneous state, and must be reset.

The cases below are assumed to be fatal: FW command timed-out, an error from FW
on closing commands, pci is offline when posting/pending a command.

In those cases we place the device into an error state: chip is reset, pending
commands are awakened and completed immediately. Subsequent commands will
return immediately.

The return code in the above cases will depend on the command. Commands which
free and close resources will return success (because the chip was reset, so
callers may safely free their kernel resources). Other commands will return -EIO.

Since the device's state was marked as error, the catas poller will
detect this and restart the device's software stack (as is done when a FW
internal error is directly detected). The device state is protected by a
persistent mutex lives on its mlx4_dev, as such no need any more for the
hcr_mutex which is removed.
Signed-off-by: NYishai Hadas <yishaih@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a given flow steering rule is invalid in respect to the current
steering configuration, print the correct error message to the system log.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If mlx4_ib_create_flow() attempts to create > 1 rules with the
firmware, and one of these registrations fail, we leaked the
already created flow rules.

One example of the leak is when the registration of the VXLAN ghost
steering rule fails, we didn't unregister the original rule requested
by the user, introduced in commit d2fce8a9 "mlx4: Set
user-space raw Ethernet QPs to properly handle VXLAN traffic".

While here, add dump of the VXLAN portion of steering rules
so it can actually be seen when flow creation fails.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the function which we use to set VXLAN DMFS (flow-steering) rules
from mlx4_en to mlx4_core. This refactoring will allow the mlx4_ib driver
to call the helper for the use case of user-space RAW Ethernet QPs, such
that they can serve VXLAN traffic too.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In B0 steering mode if promiscuous QP asks to be detached from MCG entry,
and it is the only one in this entry then the entry will never be deleted.
This is a wrong behavior since we don't want to keep those entries after
the promiscuous QP becomes non-promiscuous. Therefore remove steering
entry containing only promiscuous QP.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In current situation host is adding the promiscuous QP to all steering
entries and the default entry as well. In this case when having PV
and SR-IOV on the same setup bridge will receive all traffic that is
targeted to the other VMs. This is bad.
Solution: In SR-IOV mode host can add promiscuous QP to default entry only.
The above problem and fix are relevant for B0 steering mode only.
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In B0 steering mode when adding QPs to the default MCG entry need
to check that maximal number of QPs per MCG entry was not exceeded.
Signed-off-by: NAlexander Guller <alexg@mellanox.com>
Reviewed-by: NAviad Yehezkel <aviadye@mellanox.co.il>
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To make sure that the array index isn't used in the code with
negative value, we stop using the for loop integer iterator
outside of it.
>From now on use members count to swap the last QP with removed one.
Fix also the second occurrence of this flow in mlx4_qp_detach_common().
In mlx4_qp_detach_common() use members_count instead of
loop iterator outside of the for loop.
Signed-off-by: NDotan Barak <dotanb@dev.mellanox.co.il>
Reviewed-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When removing multicast address in B0 steering mode there is
a bug in cases where there is a single QP registered for the address,
and this QP is also promiscuous. In such cases the entry wouldn't be
deleted from the SW structure representing all Ethernet MCG entries,
but would be removed in HW. This way when driver goes to remove it
from SW and HW structures the HW deletion fails.
Moreover the same index could later be used for registering
different address, which can be Infiniband.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adopt the "info: why not propagate 'ret' from parse_trans_rule()..."
suggestion made by the smatch semantic checker on:
drivers/net/ethernet/mellanox/mlx4/mcg.c:867 mlx4_flow_attach()
Signed-off-by: NEyal Perry <eyalpe@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use a more current logging style.

o Coalesce formats
o Add missing spaces for coalesced formats
o Align arguments for modified formats
o Add missing newlines for some logging messages
o Use DRV_NAME as part of format instead of %s, DRV_NAME to
  reduce overall text.
o Use ..., ##__VA_ARGS__ instead of args... in macros
o Correct a few format typos
o Use a single line message where appropriate
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-By: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds support for N-Port VFs, this includes:
1. Adding support in the wrapped FW command
	In wrapped commands, we need to verify and convert
	the slave's port into the real physical port.
	Furthermore, when sending the response back to the slave,
	a reverse conversion should be made.
2. Adjusting sqpn for QP1 para-virtualization
	The slave assumes that sqpn is used for QP1 communication.
	If the slave is assigned to a port != (first port), we need
	to adjust the sqpn that will direct its QP1 packets into the
	correct endpoint.
3. Adjusting gid[5] to modify the port for raw ethernet
	In B0 steering, gid[5] contains the port. It needs
	to be adjusted into the physical port.
4. Adjusting number of ports in the query / ports caps in the FW commands
	When a slave queries the hardware, it needs to view only
	the physical ports it's assigned to.
5. Adjusting the sched_qp according to the port number
	The QP port is encoded in the sched_qp, thus in modify_qp we need
	to encode the correct port in sched_qp.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a fix to a regression introduced by commit:
"982290a7 net/mlx4_core: Check port number for validity
before accessing data"

IPoIB could not attach to multicast group and we get this in dmesg:
[144214.145008] ib0: failed to attach to multicast group, ret = -22
[144214.145016] ib0: couldn't attach QP to multicast group ff12:401b:ffff:0000:0000:0000:ffff:ffff
[144214.145019] ib0: multicast join failed for ff12:401b:ffff:0000:0000:0000:ffff:ffff, status -22

The cause to the problem is because port is extracted from gid[5].
Which is only valid for Ethernet.
Removed this validation in mlx4_qp_attach_common(), which is accessed
from both Ethernet and IB flows.
Error flow for bad port value in Ethernet is already exists in that
function.
Signed-off-by: NMoni Shoua <monis@mellanox.co.il>
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for allocating IB UD QPs that we can steer
traffic from.  We introduce a new firmware command FLOW_STEERING_IB_UC_QP_RANGE
and a capability bit.

This command isn't supported for VFs.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Add the low-level device commands and definitions used for TCP/IP HW offloads
of tunneled/vxlan traffic which are supported by the ConnectX3-pro NIC.

This is done through the following elements:

 - read tunneling device caps in QUERY_DEV_CAP
 - add helper function to do SET_PORT for tunneling
 - add DMFS VXLAN steering rule definitions
 - add CQE and WQE checksum offload field definitions
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Need to validate port number at mlx4_promisc_qp() before use.
Since port number is extracted from gid, as a cooked or corrupted gid
could lead to a crash.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit f4ec9e95 "mlx4_core: Change bitmap allocator to work in round-robin fashion"
introduced round-robin allocation (via bitmap) for all resources which allocate
via a bitmap.

Round robin allocation is desirable for mcgs, counters, pd's, UARs, and xrcds.
These are simply numbers, with no involvement of ICM memory mapping.

Round robin is required for QPs, since we had a problem with immediate
reuse of a 24-bit QP number (commit f4ec9e95).

However, for other resources which use the bitmap allocator and involve
mapping ICM memory -- MPTs, CQs, SRQs -- round-robin is not desirable.

What happens in these cases is the following:

ICM memory is allocated and mapped in chunks of 256K.

Since the resource allocation index goes up monotonically, the allocator
will eventually require mapping a new chunk. Now, chunks are also unmapped
when their reference count goes back to zero.  Thus, if a single app is
running and starts/exits frequently we will have the following situation:

When the app starts, a new chunk must be allocated and mapped.

When the app exits, the chunk reference count goes back to zero, and the
chunk is unmapped and freed. Therefore, the app must pay the cost of allocation
and mapping of ICM memory each time it runs (although the price is paid only when
allocating the initial entry in the new chunk).

For apps which allocate MPTs/SRQs/CQs and which operate as described above,
this presented a performance problem.

We therefore roll back the round-robin allocator modification for MPTs, CQs, SRQs.
Reported-by: NMatthew Finlay <matt@mellanox.com>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To guarantee that all unused fields in all FW commands for both inboxes
and outboxes are zeroed out, initialize the mailbox buffer to all zeroes.

This is especially important for SRIOV comm-channel virtual commands
(such as QUERY_FUNC_CAP), where if new fields are added to support new
features, the driver can depend on older kernels passing zeroes in these
fields.

In addition to zeroing out the mailbox buffer at allocation time, all
(now unnecessary) calls to memset by the callers of
mlx4_alloc_cmd_mailbox() are removed.
Signed-off-by: NMajd Dibbiny <majd@mellanox.com>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove code that triggers trivial build warnings.

drivers/net/ethernet/mellanox/mlx4/cmd.c: In function ‘mlx4_set_vf_vlan’:
drivers/net/ethernet/mellanox/mlx4/cmd.c:2256: warning: variable ‘vf_oper’ set but not used
drivers/net/ethernet/mellanox/mlx4/mcg.c: In function ‘mlx4_map_sw_to_hw_steering_mode’:
drivers/net/ethernet/mellanox/mlx4/mcg.c:648: warning: comparison of unsigned expression < 0 is always false
drivers/net/ethernet/mellanox/mlx4/mcg.c: In function ‘mlx4_map_sw_to_hw_steering_id’:
drivers/net/ethernet/mellanox/mlx4/mcg.c:685: warning: comparison of unsigned expression < 0 is always false
drivers/net/ethernet/mellanox/mlx4/mcg.c: In function ‘mlx4_hw_rule_sz’:
drivers/net/ethernet/mellanox/mlx4/mcg.c:712: warning: comparison of unsigned expression < 0 is always false
drivers/net/ethernet/mellanox/mlx4/fw.c: In function ‘mlx4_opreq_action’:
drivers/net/ethernet/mellanox/mlx4/fw.c:1732: warning: variable ‘type_m’ set but not used
drivers/net/ethernet/mellanox/mlx4/srq.c:302: warning: no previous prototype for ‘mlx4_srq_lookup’
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit adds new firmware command and new firmware event.  The firmware
raises the MLX4_EVENT_TYPE_OP_REQUIRED event in order to signal the driver it
needs to perform an administrative operation throughout the MLX4_CMD_GET_OP_REQ
command. At the moment the supported operation is adding/removing multicast
entries which are used by the firmware for handling NCSI traffic in B0
steering mode.

Also, had to swap the order of mlx4_init_mcg_table() and
mlx4_init_eq_table() to make sure that driver will get events only after
resources are initialized to handle it.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.com>
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Re-arrange some of code which fills DMFS HW structures so we can use
it from within the core driver and from the IB driver too, e.g when
verbs DMFS structures are transformed into mlx4 hardware structs.

Also, add struct mlx4_flow_handle struct which will be of use by the
DMFS verbs flow in the IB driver.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Some of struct mlx4_net_trans_rule_hw_ctrl fields were packed into u32
and accessed through bit field operations.  Expose and access them
directly as u8 or u16.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Change struct mlx4_net_trans_rule_hw_eth :: vlan_id name to vlan_tag

Change struct mlx4_net_trans_rule_hw_ib :: r_u_qpn name to l3_qpn

The patch doesn't introduce any functional change or API change
towards the firmware.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Align the names used by enum mlx4_net_trans_promisc_mode with the
actual firmware specification.  The patch doesn't introduce any
functional change or API change towards the firmware.

Remove MLX4_FS_PROMISC_FUNCTION_PORT which isn't of use.  Add new
enums MLX4_FS_{UC/MC}_SNIFFER as a preparation step for sniffer
support.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

A pre-step for supporting guests that use B0 steering over a hypervisor
that runs in DMFS (device managed flow steering mode). Add helper function
which allows to translate L2 attachments / detachments provided in B0 mode
to DMFS rules.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The allow_loopback flag was wrongly set using arithmetic bit operation, change
the code to use logical bit operation.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some of the fields for struct mlx4_net_trans_rule_hw_ctrl were packed into u32
and accessed through bit field operations. Expose and access them directly as
u8.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Device managed flow steering will be enabled only under administrator
directive provided through setting the existing module parameter
log_num_mgm_entry_size to -1 (if the device actually supports flow
steering).  If flow steering isn't requested or not available, the
driver will use the value of log_num_mgm_entry_size and B0 steering.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

The search for promisc entries was always done on the first port,
While the addition is done on the correct port.
This lead to resource leackage of promisc entries on the second
port and brought to a state where we could no longer enter to
promiscuous mode after enough iterations of "ifconfig promisc"
on the second port.
Fix that by using the correct port when searching.
Reported-by: NMarcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: NAviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To allow for usage of the flow steering Firmware structures in more locations over the driver,
such as the resource tracker, move them from mcg.c to common header files.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert a 0 error return code to a negative one, as returned elsewhere in the
function.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
identifier ret;
expression e,e1,e2,e3,e4,x;
@@

(
if (\(ret != 0\|ret < 0\) || ...) { ... return ...; }
|
ret = 0
)
... when != ret = e1
*x = \(kmalloc\|kzalloc\|kcalloc\|devm_kzalloc\|ioremap\|ioremap_nocache\|devm_ioremap\|devm_ioremap_nocache\)(...);
... when != x = e2
    when != ret = e3
*if (x == NULL || ...)
{
  ... when != ret = e4
*  return ret;
}
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Define this macro is one common place instead of duplicating it over the code
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This should be ">=" here instead of ">".  MLX4_NET_TRANS_RULE_NUM is 6.
We use "spec->id" as an array offset into the __rule_hw_sz[] and
__sw_id_hw[] arrays which have 6 elements.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NHadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The device managed flow steering API has three promiscuous modes:

1. Uplink - captures all the packets that arrive to the port.
2. Allmulti - captures all multicast packets arriving to the port.
3. Function port - for future use, this mode is not implemented yet.

Use these modes with the flow_attach and flow_detach firmware commands
according to the promiscuous state of the netdevice.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver is modified to support three operation modes.

If supported by firmware use the device managed flow steering
API, that which we call device managed steering mode. Else, if
the firmware supports the B0 steering mode use it, and finally,
if none of the above, use the A0 steering mode.

When the steering mode is device managed, the code is modified
such that L2 based rules set by the mlx4_en driver for Ethernet
unicast and multicast, and the IB stack multicast attach calls
done through the mlx4_ib driver are all routed to use the device
managed API.

When attaching rule using device managed flow steering API,
the firmware returns a 64 bit registration id, which is to be
provided during detach.

Currently the firmware is always programmed during HCA initialization
to use standard L2 hashing. Future work should be done to allow
configuring the flow-steering hash function with common, non
proprietary means.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>