Prevent using uninitialized or negative index when handling
steering entries.

Fixes: b12d93d6 ('mlx4: Add support for promiscuous mode in the new steering model.')
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce support in updating statistics of offloaded TC flower
classifiers. Currently only the DROP action is supported.
Signed-off-by: NAmir Vadai <amirva@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a counter has the aging flag set when created, it is added to a list
of counters that will be queried periodically from a workqueue.  query
result and last use timestamp are cached.
add/del counter must be very efficient since thousands of such
operations might be issued in a second.
There is only a single reference to counters without aging, therefore
no need for locks.
But, counters with aging enabled are stored in a list. In order to make
code as lockless as possible, all the list manipulation and access to
hardware is done from a single context - the periodic counters query
thread.

The hardware supports multiple counters per FTE, however currently we
are using one counter for each FTE.
Signed-off-by: NAmir Vadai <amirva@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When adding a flow steering rule with a counter, need to supply a
destination of type MLX5_FLOW_DESTINATION_TYPE_COUNTER, with a pointer
to a struct mlx5_fc.
Also, MLX5_FLOW_CONTEXT_ACTION_COUNT bit should be set in the action.
Signed-off-by: NAmir Vadai <amirva@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Getting packet/byte statistics on flows is done through flow counters.
Implement the firmware commands to alloc, free and query flow counters.
Signed-off-by: NAmir Vadai <amirva@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use a macro instead of copying the OP name.
Signed-off-by: NAmir Vadai <amirva@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We turn the feature ON, only for servers with PCI BW < MAX LINK BW, as it
helps reducing PCI pressure on weak PCI slots, but it adds some software
overhead.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make the MPWQE/Striding RQ default configuration dynamic and not
statically set at compile time.  Now at driver load we set
stride size and num strides dynamically.

By default we use same values as before, but when CQE compression
is enabled, we set larger stride size to benefit from CQE
compression for larger packets.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CQE compression feature is meant to save PCIe bandwidth by
compressing few CQEs into smaller amount of bytes on PCIe.
CQE compression can be selectively enabled per CQ.  By default
is disabled for now and will be enabled later on.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I accidently let Arnd's VXLAN dependency changes slip into net-next,
they are only appropriate for net.

Also the flow steering structural changes to mlx5e_priv got scrambled
during the merge resolution as well.

Fix that all up.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

VXLAN can be disabled at compile-time or it can be a loadable
module while mlx5 is built-in, which leads to a link error:

drivers/net/built-in.o: In function `mlx5e_create_netdev':
ntb_netdev.c:(.text+0x106de4): undefined reference to `vxlan_get_rx_port'

This avoids the link error and makes the vxlan code optional,
like the other ethernet drivers do as well.

Link: https://patchwork.ozlabs.org/patch/589296/
Fixes: b3f63c3d ("net/mlx5e: Add netdev support for VXLAN tunneling")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 69976fb1.

We cannot select VXLAN when IPv4 support is disabled, that just gives
us additional build errors, including:

warning: (MLX5_CORE_EN) selects VXLAN which has unmet direct dependencies (NETDEVICES && NET_CORE && INET)
In file included from ../drivers/net/vxlan.c:36:0:
include/net/udp_tunnel.h: In function 'udp_tunnel_handle_offloads':
include/net/udp_tunnel.h:112:9: error: implicit declaration of function 'iptunnel_handle_offloads' [-Werror=implicit-function-declaration]
  return iptunnel_handle_offloads(skb, type);
         ^~~~~~~~~~~~~~~~~~~~~~~~

I'm sending a proper fix for the original bug in a separate patch.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes: 0f433fa0 ("mlxsw: spectrum_buffers: Implement shared buffer configuration")
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When we fail to set the flooding configuration for the broadcast and
unregistered multicast traffic, we should revert the flooding
configuration of the unknown unicast traffic.

Fixes: 0293038e ("mlxsw: spectrum: Add support for flood control")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make the leave procedure in the error path symmetric to the join
procedure and first remove the port from the collector before
potentially destroying the LAG.

Fixes: 0d65fc13 ("mlxsw: spectrum: Implement LAG port join/leave")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use htons instead of unconditionally byte swapping nexthdr.  On a little
endian systems shifting the byte is correct behavior, but it results in
incorrect csums on big endian architectures.

Fixes: f8c6455b ('net/mlx4_en: Extend checksum offloading by CHECKSUM COMPLETE')
Signed-off-by: NDaniel Jurgens <danielj@mellanox.com>
Reviewed-by: NCarol Soto <clsoto@us.ibm.com>
Tested-by: NCarol Soto <clsoto@us.ibm.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dma_alloc_coherent() function returns a virtual address which can
be used for coherent access to the underlying memory.  On some
architectures, like arm64, undefined behavior results if this memory is
also accessed via virtual mappings that are not coherent.  Because of
their undefined nature, operations like virt_to_page() return garbage
when passed virtual addresses obtained from dma_alloc_coherent().  Any
subsequent mappings via vmap() of the garbage page values are unusable
and result in bad things like bus errors (synchronous aborts in ARM64
speak).

The mlx4 driver contains code that does the equivalent of:
vmap(virt_to_page(dma_alloc_coherent)), this results in an OOPs when the
device is opened.

Prevent Ethernet driver to run this problematic code by forcing it to
allocate contiguous memory. As for the Infiniband driver, at first we
are trying to allocate contiguous memory, but in case of failure roll
back to work with fragmented memory.
Signed-off-by: NHaggai Abramovsky <hagaya@mellanox.com>
Signed-off-by: NYishai Hadas <yishaih@mellanox.com>
Reported-by: NDavid Daney <david.daney@cavium.com>
Tested-by: NSinan Kaya <okaya@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Add support to configure trusted vf attribute through trust_vf_ndo.

- Upon VF trust setting change we update vport context to refresh
 allmulti/promisc or any trusted vf attributes that we didn't trust the
 VF for before.

- Lock the eswitch state lock on vport event in order to synchronise the
 vport context updates , this will prevent contention with vport trust
 setting change which will trigger vport mac list update.
Signed-off-by: NMohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add promisc_change as a trigger to vport context change event.
Add set vport promisc/allmulti functions to add vport to promiscuous
flowtable rules.
Upon promisc/allmulti rx mode vf request add the vport to
the relevant promiscuous group (Allmulti/Promisc group) so the relevant
traffic will be forwarded to it.
Upon allmulti vf request add the vport to each existing multicast fdb
rule.
Upon adding/removing mcast address from a vport, update all other
allmulti vports.
Signed-off-by: NMohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add promiscuous and allmulti steering groups in FDB table.
Besides the full match L2 steering rules group, we added
two more groups to catch the "miss" rules traffic:
* Allmulti group: One rule that forwards any mcast traffic coming from
either uplink or VFs/PF vports
* Promisc group: One rule that forwards all unmatched traffic coming
from uplink.

Needed for downstream privileged VF promisc and allmulti support.
Signed-off-by: NMohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the usage of explicit cleanup function and use existing vport
change handler. Calling vport change handler while vport
is disabled will cleanup the vport resources.
Signed-off-by: NMohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable ingress/egress ACL tables only when we need to configure ACL
rules.
Disable ingress/egress ACL tables once all ACL rules are removed.

All VF outgoing/incoming traffic need to go through the ingress/egress ACL
tables.
Adding/Removing these tables on demand will save unnecessary hops in the
flow steering when the ACL tables are empty.
Signed-off-by: NMohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Configure ingress and egress vport ACL rules according to spoofchk
admin parameters.

Ingress ACL flow table rules:
if (!spoofchk && !vst) allow all traffic.
else :
1) one of the following rules :
* if (spoofchk && vst) allow only untagged traffic with smac=original
mac sent from the VF.
* if (spoofchk && !vst) allow only traffic with smac=original mac sent
from the VF.
* if (!spoofchk && vst) allow only untagged traffic.
2) drop all traffic that didn't hit #1.

Add support for set vf spoofchk ndo.

Add non zero mac validation in case of spoofchk to set mac ndo:
when setting new mac we need to validate that the new mac is
not zero while the spoofchk is on because it is illegal
combination.
Signed-off-by: NMohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Configure ingress and egress vport ACL rules according to
vlan and qos admin parameters.

Ingress ACL flow table rules:
1) drop any tagged packet sent from the VF
2) allow other traffic (default behavior)

Egress ACL flow table rules:
1) allow only tagged traffic with vlan_tag=vst_vid.
2) drop other traffic.
Signed-off-by: NMohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Create egress/ingress ACLs per VF vport at vport enable.

Ingress ACL:
	- one flow group to drop all tagged traffic in VST mode.

Egress ACL:
	- one flow group that allows only untagged traffic with
          smac that is equals to the original mac (anti-spoofing).
        - one flow group that allows only untagged traffic.
        - one flow group that allows only  smac that is equals
          to the original mac (anti-spoofing).
        (note: only one of the above group has active rule)
	- star rule will be used to drop all other traffic.

By default no rules are generated, unless VST is explicitly requested.
Signed-off-by: NMohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix memory leak in case query nic vport command failed.

Fixes: 81848731 ('net/mlx5: E-Switch, Add SR-IOV (FDB) support')
Signed-off-by: NMohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Vport spin lock can be replaced with synchronize_irq() in the right
place, this will remove the need of locking inside irq context.
Locking in esw_enable_vport is not required since vport events are yet
to be enabled, and at esw_disable_vport it is sufficient to
synchronize_irq() to guarantee no further vport events handlers will be
scheduled.
Signed-off-by: NMohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update the relevant flow steering device structs and commands to
support vport.
Update the flow steering core API to receive vport number.
Add ingress and egress ACL flow table name spaces.
Add ACL flow table support:
* ACL (Access Control List) flow table is a table that contains
only allow/drop steering rules.

* We have two types of ACL flow tables - ingress and egress.

* ACLs handle traffic sent from/to E-Switch FDB table, Ingress refers to
traffic sent from Vport to E-Switch and Egress refers to traffic sent
from E-Switch to vport.

* Ingress ACL flow table allow/drop rules is checked against traffic
sent from VF.

* Egress ACL flow table allow/drop rules is checked against traffic sent
to VF.
Signed-off-by: NMohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

en_arfs.o should be compiled only if both CONFIG_MLX5_CORE_EN
and CONFIG_RFS_ACCEL are enabled. en_arfs calls to rps_may_expire_flow
which is compiled only if CONFIG_RFS_ACCEL is defined.

Move en_arfs.o compilation dependency to be under CONFIG_MLX5_CORE_EN
and wrap the en_arfs.c content with ifdef of CONFIG_RFS_ACCEL.

Fixes: 1cabe6b0 ('net/mlx5e: Create aRFS flow tables')
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Reported-by: NAlexei Starovoitov <alexei.starovoitov@gmail.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mlx5 driver exposes support for TSO6 but not IPv6 csum for hardware
encapsulated tunnels.  This leads to issues as it triggers warnings in
skb_checksum_help as it ends up being called as we report supporting the
segmentation but not the checksumming for IPv6 frames.

This patch corrects that and drops 2 features that don't actually need to
be supported in hw_enc_features since they are Rx features and don't
actually impact anything by being present in hw_enc_features.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch assumes that the mlx5 hardware will ignore existing IPv4/v6
header fields for length and checksum as well as the length and checksum
fields for outer UDP headers.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

>From what I can tell the ConnectX-3 will support an inner IPv6 checksum and
segmentation offload, however it cannot support outer IPv6 headers.  This
assumption is based on the fact that I could see the checksum being
offloaded for inner header on IPv4 tunnels, but not on IPv6 tunnels.

For this reason I am adding the feature to the hw_enc_features and adding
an extra check to the features_check call that will disable GSO and
checksum offload in the case that the encapsulated frame has an outer IP
version of that is not 4.  The check in mlx4_en_features_check could be
removed if at some point in the future a fix is found that allows the
hardware to offload segmentation/checksum on tunnels with an outer IPv6
header.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch assumes that the mlx4 hardware will ignore existing IPv4/v6
header fields for length and checksum as well as the length and checksum
fields for outer UDP headers.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The vxlan add/delete port NDOs are called under rcu lock.
The current mlx5e implementation can potentially block in these
calls, which is not allowed.  Move to using the mlx5e workqueue
to handle these NDOs.

Fixes: b3f63c3d ('net/mlx5e: Add netdev support for VXLAN tunneling')
Signed-off-by: NMatthew Finlay <matt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement a mlx5e workqueue to handle all mlx5e specific tasks.  Move
all tasks currently using the system workqueue to the new workqueue.
This is in preparation for vxlan using the mlx5e workqueue in order to
schedule port add/remove operations.
Signed-off-by: NMatthew Finlay <matt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When MLX5_EN=y MLX5_CORE=y and VXLAN=m there is a linker error for
vxlan_get_rx_port() due to the fact that VXLAN is a module. Change Kconfig
to select VXLAN when MLX5_CORE=y. When MLX5_CORE=m there is no dependency
on the value of VXLAN.

Fixes: b3f63c3d ('net/mlx5e: Add netdev support for VXLAN tunneling')
Signed-off-by: NMatthew Finlay <matt@mellanox.com>
Reported-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When freeing UAR the driver tries to unmap uar->map and uar->bf_map
which are mutually exclusive thus always unmapping a NULL pointer.
Make sure we only call iounmap() once, for the actual mapping.

Fixes: 0ba42241 ('net/mlx5: Fix global UAR mapping')
Signed-off-by: NGal Pressman <galp@mellanox.com>
Reported-by: NDoron Tsur <doront@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Accelerated RFS requires that ntuple filtering is enabled via
ethtool and driver supports ndo_rx_flow_steer.
When the ntuple filtering is enabled, we modify the l3_l4 ttc
rules to point on the aRFS flow tables and when the filtering
is disabled, we modify the l3_l4 ttc rules to point on the RSS
TIRs.
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement ndo_rx_flow_steer ndo.
A new flow steering rule will be composed from the
skb 4-tuple and added to the hardware aRFS flow table.

Each rule is stored in an internal hash table, if such
skb 4-tuple rule already exists we update the corresponding
hardware steering rule with the new destination.

For garbage collection rps_may_expire_flow will be
invoked for a limited amount of old rules upon any
ndo_rx_flow_steer invocation.
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Create the following four flow tables for aRFS usage:
1. IPv4 TCP - filtering 4-tuple of IPv4 TCP packets.
2. IPv6 TCP - filtering 4-tuple of IPv6 TCP packets.
3. IPv4 UDP - filtering 4-tuple of IPv4 UDP packets.
4. IPv6 UDP - filtering 4-tuple of IPv6 UDP packets.

Each flow table has two flow groups: one for the 4-tuple
filtering (full match)  and the other contains * rule for miss rule.

Full match rule means a hit for aRFS and packet will be forwarded
to the dedicated RQ/Core, miss rule packets will be forwarded to
default RSS hashing.
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>