Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 13 7月, 2008 3 次提交
  3. 11 7月, 2008 2 次提交
  5. 10 7月, 2008 3 次提交
  7. 07 7月, 2008 2 次提交
  9. 19 5月, 2008 1 次提交
  11. 10 5月, 2008 1 次提交
  13. 30 4月, 2008 1 次提交
  15. 19 4月, 2008 3 次提交
    • J
      [ARM] 4867/1: Adds flash, udc, mci support for gumstix F boards · 90b8fc34
      由 Jaya Kumar 提交于 
      This patch implements support for Gumstix-F flash, udc and mci. Fixes since the last time are:
- Steve Sakoman as maintainer
- cleanup for udc and mci setup
Signed-off-by: NJaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
      90b8fc34
    • E
      [ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x} · 7facc2f9
      由 eric miao 提交于 
      Pin configuration on pxa{25x,27x} has now separated from generic GPIO
into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed
from pxa3xx and is used here to alert the difference between the two
concepts: pin configuration and generic GPIOs.  A GPIO can be called
a "GPIO" _only_ when the corresponding pin is configured so.

A pin configuration on pxa{25x,27x} is composed of:

    - alternate function selection (or pin mux as commonly called)
    - low power state or sleep state
    - wakeup enabling from low power mode

The following MFP_xxx bit definitions in mfp.h are re-used:

    - MFP_PIN(x)
    - MFP_AFx
    - MFP_LPM_DRIVE_{LOW, HIGH}
    - MFP_LPM_EDGE_*

Selecting alternate function on pxa{25x, 27x} involves configuration
of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT}
are introduced. And pin configurations are defined by the following
two macros:

    - MFP_CFG_IN  : for input alternate functions
    - MFP_CFG_OUT : for output alternate functions

Every configuration should provide a low power state if it configured
as output using MFP_CFG_OUT().  As a general guideline, the low power
state should be decided to minimize the overall power dissipation. As
an example, it is better to drive the pin as high level in low power
mode if the GPIO is configured as an active low chip select.

Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid
side effects when it is firstly configured as output.  The actual
direction of the GPIO is configured by gpio_direction_{input, output}

Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus
the device based enable_irq_wake() mechanism is not applicable here.

E.g.  invoking enable_irq_wake() with a GPIO IRQ as in the following
code to enable OTG wakeup is by no means portable and intuitive, and
it is valid _only_ when GPIO35 is configured as USB_P2_1:

    enable_irq_wake( gpio_to_irq(35) );

To make things worse, not every GPIO is able to wakeup the system.
Only a small number of them can, on either rising or falling edge,
or when level is high (for keypad GPIOs).

Thus, another new bit is introduced to indicate that the GPIO will
wakeup the system:

    - MFP_LPM_WAKEUP_ENABLE

The following macros can be used in platform code, and be OR'ed to
the GPIO configuration to enable its wakeup:

    - WAKEUP_ON_EDGE_{RISE, FALL, BOTH}
    - WAKEUP_ON_LEVEL_HIGH

The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is
no edge settings for those GPIOs.

These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case
that platform code author is careless enough.

The tradeoff here is that the wakeup source is fully determined by
the platform configuration, instead of enable_irq_wake().
Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
      7facc2f9
    • E
      [ARM] pxa: rename mfp.c to mfp-pxa3xx.c to indicate it's pxa3xx specific · 06b2666e
      由 eric miao 提交于 
      Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
      06b2666e
  17. 06 2月, 2008 1 次提交
  19. 04 2月, 2008 1 次提交
  21. 28 1月, 2008 6 次提交
  23. 26 1月, 2008 3 次提交
  25. 16 10月, 2007 3 次提交
  27. 21 7月, 2007 1 次提交
  29. 29 6月, 2006 1 次提交
  31. 20 6月, 2006 1 次提交
  33. 29 3月, 2006 1 次提交
  35. 22 3月, 2006 1 次提交
  37. 13 11月, 2005 3 次提交
  39. 11 11月, 2005 1 次提交
    • L
      [ARM] 3098/1: pxa2xx disable ssp irq · b216c018
      由 Liam Girdwood 提交于 
      Patch from Liam Girdwood

This patch allows users of the pxa SSP driver to register their own irq
handlers instead of using the default SSP handler. It also cleans up the
CKEN clock and irq detection as the values are now stored in a table.

This patch replaces 2845/1

Changes:-
o Added flags parameter to ssp_init()
o Added SSP_NO_IRQ flag to disable registering of ssp irq handler (for
drivers that want to register their own handler)
o Cleaned up clock and irq detection, values are now stored in table.
o Added build changes to allow other drivers (e.g audio) to select the
ssp driver.
o corgi_ssp.c changed to use new interface.
Signed-off-by: NLiam Girdwood <liam.girdwood@wolfsonmicro.com>
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
      b216c018
  41. 06 11月, 2005 1 次提交