Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>

Scripted with coccinelle.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

This patch (as1453) fixes a long-standing bug in the ehci-hcd driver.

There is no need to set the Halt bit in the overlay region for an
unlinked or blocked QH.  Contrary to what the comment says, setting
the Halt bit does not cause the QH to be patched later; that decision
(made in qh_refresh()) depends only on whether the QH is currently
pointing to a valid qTD.  Likewise, setting the Halt bit does not
prevent completions from activating the QH while it is "stopped"; they
are prevented by the fact that qh_completions() temporarily changes
qh->qh_state to QH_STATE_COMPLETING.

On the other hand, there are circumstances in which the QH will be
reactivated _without_ being patched; this happens after an URB beyond
the head of the queue is unlinked.  Setting the Halt bit will then
cause the hardware to see the QH with both the Active and Halt bits
set, an invalid combination that will prevent the queue from
advancing and may even crash some controllers.

Apparently the only reason this hasn't been reported before is that
unlinking URBs from the middle of a running queue is quite uncommon.
However Test 17, recently added to the usbtest driver, does exactly
this, and it confirms the presence of the bug.

In short, there is no reason to set the Halt bit for an unlinked or
blocked QH, and there is a very good reason not to set it.  Therefore
the code that sets it is removed.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NAndiry Xu <andiry.xu@amd.com>
CC: David Brownell <david-b@pacbell.net>
CC: <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This silences warnings such as

drivers/video/tmiofb.c: In function 'tmiofb_hw_init':
drivers/video/tmiofb.c:270: warning: initialization discards qualifiers from pointer target type

These were added by me in commit 2a79bb1d.
Signed-off-by: NAndres Salomon <dilinger@queued.net>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

No need to explicitly set the cell's platform_data/data_size.

Modify clients to use mfd_get_cell helper function instead of
accessing platform_data directly.
Signed-off-by: NAndres Salomon <dilinger@queued.net>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Use XOR to invert the cycle bit, instead of a more complicated
calculation.  Eliminate a check for the link TRB type in find_trb_seg().
We know that there will always be a link TRB at the end of a segment, so
xhci_segment->trbs[TRBS_PER_SEGMENT - 1] will always have a link TRB type.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: NTakashi Iwai <tiwai@suse.de>

When an endpoint stalls, we need to update the xHCI host's internal
dequeue pointer to move it past the stalled transfer.  This includes
updating the cycle bit (TRB ownership bit) if we have moved the dequeue
pointer past a link TRB with the toggle cycle bit set.

When we're trying to find the new dequeue segment, find_trb_seg() is
supposed to keep track of whether we've passed any link TRBs with the
toggle cycle bit set.  However, this while loop's body

	while (cur_seg->trbs > trb ||
			&cur_seg->trbs[TRBS_PER_SEGMENT - 1] < trb) {

Will never get executed if the ring only contains one segment.
find_trb_seg() will return immediately, without updating the new cycle
bit.  Since find_trb_seg() has no idea where in the segment the TD that
stalled was, make the caller, xhci_find_new_dequeue_state(), check for
this special case and update the cycle bit accordingly.

This patch should be queued to kernels all the way back to 2.6.31.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: NTakashi Iwai <tiwai@suse.de>
Cc: stable@kernel.org

When an endpoint stalls, the xHCI driver must move the endpoint ring's
dequeue pointer past the stalled transfer.  To do that, the driver issues
a Set TR Dequeue Pointer command, which will complete some time later.

Takashi was having issues with USB 1.1 audio devices that stalled, and his
analysis of the code was that the old code would not update the xHCI
driver's ring dequeue pointer after the command completes.  However, the
dequeue pointer is set in xhci_find_new_dequeue_state(), just before the
set command is issued to the hardware.

Setting the dequeue pointer before the Set TR Dequeue Pointer command
completes is a dangerous thing to do, since the xHCI hardware can fail the
command.  Instead, store the new dequeue pointer in the xhci_virt_ep
structure, and update the ring's dequeue pointer when the Set TR dequeue
pointer command completes.

While we're at it, make sure we can't queue another Set TR Dequeue Command
while the first one is still being processed.  This just won't work with
the internal xHCI state code.  I'm still not sure if this is the right
thing to do, since we might have a case where a driver queues multiple
URBs to a control ring, one of the URBs Stalls, and then the driver tries
to cancel the second URB.  There may be a race condition there where the
xHCI driver might try to issue multiple Set TR Dequeue Pointer commands,
but I would have to think very hard about how the Stop Endpoint and
cancellation code works.  Keep the fix simple until when/if we run into
that case.

This patch should be queued to kernels all the way back to 2.6.31.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: NTakashi Iwai <tiwai@suse.de>
Cc: stable@kernel.org

USB_PORT_STAT_SUPER_SPEED is a made up symbol that the USB core used to
track whether USB ports had a SuperSpeed device attached.  This is a
linux-internal symbol that was used when SuperSpeed and non-SuperSpeed
devices would show up under the same xHCI roothub.  This particular
port status is never returned by external USB 3.0 hubs.  (Instead they
have a USB_PORT_STAT_SPEED_5GBPS that uses a completely different speed
mask.)

Now that the xHCI driver registers two roothubs, USB 3.0 devices will only
show up under USB 3.0 hubs.  Rip out USB_PORT_STAT_SUPER_SPEED and replace
it with calls to hub_is_superspeed().
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

When the xHCI host controller is halted, it won't respond to commands
placed on the command ring.  So if an URB is cancelled after the first
roothub is deallocated, it will try to place a stop endpoint command on
the command ring, which will fail.  The command watchdog timer will fire
after five seconds, and the host controller will be marked as dying, and
all URBs will be completed.

Add a flag to the xHCI's internal state variable for when the host
controller is halted.  Immediately return the canceled URB if the host
controller is halted.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Make sure the HCD_FLAG_HW_ACCESSIBLE flag is mirrored by both roothubs,
since it refers to whether the shared hardware is accessible.  Make sure
each bus is marked as suspended by setting usb_hcd->state to
HC_STATE_SUSPENDED when the PCI host controller is resumed.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

When a host controller has lost power during a suspend, we must
reinitialize it.  Now that the xHCI host has two roothubs, xhci_run() and
xhci_stop() expect to be called with both usb_hcd structures.  Be sure
that the re-initialization code in xhci_resume() mirrors the process the
USB PCI probe function uses.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Return early in the roothub control and status functions if the xHCI host
controller is not electrically present in the system (register reads
return all "fs").  This issue only shows up when the xHCI driver registers
two roothubs and the host controller is removed from the system.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

The USB core allocates a USB 2.0 roothub descriptor that has room for 31
(USB_MAXCHILDREN) ports' worth of DeviceRemovable and PortPwrCtrlMask
fields.  Limit the number of USB 2.0 roothub ports accordingly.  I don't
expect to run into this limitation ever, but this prevents a buffer
overflow issue in the roothub descriptor filling code.

Similarly, a USB 3.0 hub can only have 15 downstream ports, so limit the
USB 3.0 roothub to 15 USB 3.0 ports.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Return the correct xHCI roothub descriptor, based on whether the roothub
is marked as USB 3.0 or USB 2.0 in usb_hcd->bcdUSB.  Fill in
DeviceRemovable for the USB 2.0 and USB 3.0 roothub descriptors, using the
Device Removable bit in the port status and control registers.  xHCI is
the first host controller to actually properly set these bits (other hosts
say all devices are removable).

When userspace asks for a USB 2.0-style hub descriptor for the USB 3.0
roothub, stall the endpoint.  This is what real external USB 3.0 hubs do,
and we don't want to return a descriptor that userspace didn't ask for.

The USB core is already fixed to always ask for USB 3.0-style hub
descriptors.  Only usbfs (typically lsusb) will ask for the USB 2.0-style
hub descriptors.  This has already been fixed in usbutils version 0.91,
but the kernel needs to deal with older usbutils versions.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

This patch changes the xHCI driver to allocate two roothubs.  This touches
the driver initialization and shutdown paths, roothub emulation code, and
port status change event handlers.  This is a rather large patch, but it
can't be broken up, or it would break git-bisect.

Make the xHCI driver register its own PCI probe function.  This will call
the USB core to create the USB 2.0 roothub, and then create the USB 3.0
roothub.  This gets the code for registering a shared roothub out of the
USB core, and allows other HCDs later to decide if and how many shared
roothubs they want to allocate.

Make sure the xHCI's reset method marks the xHCI host controller's primary
roothub as the USB 2.0 roothub.  This ensures that the high speed bus will
be processed first when the PCI device is resumed, and any USB 3.0 devices
that have migrated over to high speed will migrate back after being reset.
This ensures that USB persist works with these odd devices.

The reset method will also mark the xHCI USB2 roothub as having an
integrated TT.  Like EHCI host controllers with a "rate matching hub" the
xHCI USB 2.0 roothub doesn't have an OHCI or UHCI companion controller.
It doesn't really have a TT, but we'll lie and say it has an integrated
TT.  We need to do this because the USB core will reject LS/FS devices
under a HS hub without a TT.

Other details:
-------------

The roothub emulation code is changed to return the correct number of
ports for the two roothubs.  For the USB 3.0 roothub, it only reports the
USB 3.0 ports.  For the USB 2.0 roothub, it reports all the LS/FS/HS
ports.  The code to disable a port now checks the speed of the roothub,
and refuses to disable SuperSpeed ports under the USB 3.0 roothub.

The code for initializing a new device context must be changed to set the
proper roothub port number.  Since we've split the xHCI host into two
roothubs, we can't just use the port number in the ancestor hub.  Instead,
we loop through the array of hardware port status register speeds and find
the Nth port with a similar speed.

The port status change event handler is updated to figure out whether the
port that reported the change is a USB 3.0 port, or a non-SuperSpeed port.
Once it figures out the port speed, it kicks the proper roothub.

The function to find a slot ID based on the port index is updated to take
into account that the two roothubs will have over-lapping port indexes.
It checks that the virtual device with a matching port index is the same
speed as the passed in roothub.

There's also changes to the driver initialization and shutdown paths:

 1. Make sure that the xhci_hcd pointer is shared across the two
    usb_hcd structures.  The xhci_hcd pointer is allocated and the
    registers are mapped in when xhci_pci_setup() is called with the
    primary HCD.  When xhci_pci_setup() is called with the non-primary
    HCD, the xhci_hcd pointer is stored.

 2. Make sure to set the sg_tablesize for both usb_hcd structures.  Set
    the PCI DMA mask for the non-primary HCD to allow for 64-bit or 32-bit
    DMA.  (The PCI DMA mask is set from the primary HCD further down in
    the xhci_pci_setup() function.)

 3. Ensure that the host controller doesn't start kicking khubd in
    response to port status changes before both usb_hcd structures are
    registered.  xhci_run() only starts the xHC running once it has been
    called with the non-primary roothub.  Similarly, the xhci_stop()
    function only halts the host controller when it is called with the
    non-primary HCD.  Then on the second call, it resets and cleans up the
    MSI-X irqs.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

xhci_find_slot_id_by_port() tries to map the port index to the slot ID for
the USB device.  In the future, there will be two xHCI roothubs, and their
port indices will overlap.  Therefore, xhci_find_slot_id_by_port() will
need to use information in the roothub's usb_hcd structure to map the port
index and roothub speed to the right slot ID.

Add a new parameter to xhci_find_slot_id_by_port(), in order to pass in
the roothub's usb_hcd structure.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

There are several variables in the xhci_hcd structure that are related to
bus suspend and resume state.  There are a couple different port status
arrays that are accessed by port index.  Move those variables into a
separate structure, xhci_bus_state.  Stash that structure in xhci_hcd.

When we have two roothhubs that can be suspended and resumed separately,
we can have two xhci_bus_states, and index into the port arrays in each
structure with the fake roothub port index (not the real hardware port
index).
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

In the upcoming patches, the roothub emulation code will need to return
port status and port change buffers based on whether they are called with
the xHCI USB 2.0 or USB 3.0 roothub.  To facilitate that, make the roothub
code index into an array of port addresses with wIndex, rather than
calculating the address using the offset and the address of the PORTSC
registers.  Later we can set the port array to be the array of USB 3.0
port addresses, or the USB 2.0 port addresses, depending on the roothub
passed in.

Create a temporary (statically sized) port array and fill it in with both
USB 3.0 and USB 2.0 port addresses.  This is inefficient to do for every
roothub call, but this is needed for git bisect compatibility.  The
temporary port array will be deleted in a subsequent patch.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

The hcd->flags are in a sorry state.  Some of them are clearly specific to
the particular roothub (HCD_POLL_RH, HCD_POLL_PENDING, and
HCD_WAKEUP_PENDING), but some flags are related to PCI device state
(HCD_HW_ACCESSIBLE and HCD_SAW_IRQ).  This is an issue when one PCI device
can have two roothubs that share the same IRQ line and hardware.

Make sure to set HCD_FLAG_SAW_IRQ for both roothubs when an interrupt is
serviced, or an URB is unlinked without an interrupt.  (We can't tell if
the host actually serviced an interrupt for a particular bus, but we can
tell it serviced some interrupt.)

HCD_HW_ACCESSIBLE is set once by usb_add_hcd(), which is set for both
roothubs as they are added, so it doesn't need to be modified.
HCD_POLL_RH and HCD_POLL_PENDING are only checked by the USB core, and
they are never set by the xHCI driver, since the roothub never needs to be
polled.

The usb_hcd's state field is a similar mess.  Sometimes the state applies
to the underlying hardware: HC_STATE_HALT, HC_STATE_RUNNING, and
HC_STATE_QUIESCING.  But sometimes the state refers to the roothub state:
HC_STATE_RESUMING and HC_STATE_SUSPENDED.

Alan Stern recently made the USB core not rely on the hcd->state variable.
Internally, the xHCI driver still checks for HC_STATE_SUSPENDED, so leave
that code in.  Remove all references to HC_STATE_HALT, since the xHCI
driver only sets and doesn't test those variables.  We still have to set
HC_STATE_RUNNING, since Alan's patch has a bug that means the roothub
won't get registered if we don't set that.

Alan's patch made the USB core check a different variable when trying to
determine whether to suspend a roothub.  The xHCI host has a split
roothub, where two buses are registered for one PCI device.  Each bus in
the xHCI split roothub can be suspended separately, but both buses must be
suspended before the PCI device can be suspended.  Therefore, make sure
that the USB core checks HCD_RH_RUNNING() for both roothubs before
suspending the PCI host.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Instead of allocating space for the whole xhci_hcd structure at the end of
usb_hcd, make the USB core allocate enough space for a pointer to the
xhci_hcd structure.  This will make it easy to share the xhci_hcd
structure across the two roothubs (the USB 3.0 usb_hcd and the USB 2.0
usb_hcd).

Deallocate the xhci_hcd at PCI remove time, so the hcd_priv will be
deallocated after the usb_hcd is deallocated.  We do this by registering a
different PCI remove function that calls the usb_hcd_pci_remove()
function, and then frees the xhci_hcd.  usb_hcd_pci_remove() calls
kput() on the usb_hcd structure, which will deallocate the memory that
contains the hcd_priv pointer, but not the memory it points to.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Make sure to call into the USB core's link, unlink, and giveback URB
functions with the usb_hcd pointer found by using urb->dev->bus.  This
will avoid confusion later, when the xHCI driver will deal with URBs from
two separate buses (the USB 3.0 roothub and the faked USB 2.0 roothub).

Assume xhci_urb_dequeue() will be called with the proper usb_hcd.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Commit d199c96d by Alan Stern ensured that low speed and full speed
devices below a high speed hub without a transaction translator (TT) would
never get enumerated.  Simplify the check for a TT in the xHCI virtual
device allocation to only check if the usb_device references a parent's
TT.

Make sure not to set the TT information on LS/FS devices directly
connected to the roothub.  The xHCI host doesn't really have a TT, and the
host will throw an error when those virtual device TT fields are set for a
device connected to the roothub.  We need this check because the xHCI
driver will shortly register two roothubs: a USB 2.0 roothub and a USB 3.0
roothub.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Update the USB core to deal with USB 3.0 hubs.  These hubs have a slightly
different hub descriptor than USB 2.0 hubs, with a fixed (rather than
variable length) size.  Change the USB core's hub descriptor to have a
union for the last fields that differ.  Change the host controller drivers
that access those last fields (DeviceRemovable and PortPowerCtrlMask) to
use the union.

Translate the new version of the hub port status field into the old
version that khubd understands.  (Note: we need to fix it to translate the
roothub's port status once we stop converting it to USB 2.0 hub status
internally.)

Add new code to handle link state change status.  Send out new control
messages that are needed for USB 3.0 hubs, like Set Hub Depth.

This patch is a modified version of the original patch submitted by John
Youn.  It's updated to reflect the removal of the "bitmap" #define, and
change the hub descriptor accesses of a couple new host controller
drivers.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: Tony Olech <tony.olech@elandigitalsystems.com>
Cc: "Robert P. J. Day" <rpjday@crashcourse.ca>
Cc: Max Vozeler <mvz@vozeler.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Rodolfo Giometti <giometti@linux.it>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Anton Vorontsov <avorontsov@mvista.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Lothar Wassmann <LW@KARO-electronics.de>
Cc: Olav Kongas <ok@artecdesign.ee>
Cc: Martin Fuzzey <mfuzzey@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <dbrownell@users.sourceforge.net>

The USB core will set hcd->state to HC_STATE_RUNNING before calling
xhci_run, so there's no point in setting it twice.  The USB core also
doesn't pay attention to HC_STATE_RUNNING on the resume path anymore; it
uses HCD_RH_RUNNING(), which looks at hcd->flags & (1U <<
HCD_FLAG_RH_RUNNING.  Therefore, it's safe to remove the state set in
xhci_bus_resume().
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

The xHCI driver doesn't ever test hcd->state for HC_STATE_HALT.  The USB
core recently stopped using it internally, so there's no point in setting
it in the driver.  We still need to set HC_STATE_RUNNING in order to make
it past the USB core's hcd->state check in register_roothub().
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

xHCI 1.0 spec specifies the xHC shall halt within 16ms after software clears
Run/Stop bit. In xHCI 0.96 spec the time limit is 16 microframes (2ms), it's
too short and often cause dmesg shows "Host controller not halted, aborting
reset." message when rmmod xhci-hcd.

Modify the time limit to comply with xHCI 1.0 specification and prevents the
warning message showing when remove xhci-hcd.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Set hcd->state = HC_STATE_SUSPENDED if there is a power loss during system
resume or the system is hibernated, otherwise leave it be. The variable
old_state is redundant and made an unreachable code path, so remove it.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

The xhci_bus_suspend() and xhci_bus_resume() functions are a bit hard to
read, because they have an ambiguously named variable "port".  Rename it
to "port_index".  Introduce a new temporary variable, "max_ports" that
holds the maximum number of roothub ports the host controller supports.
This will reduce the number of register reads, and make it easy to change
the maximum number of ports when there are two roothubs.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

The USB core only allows up to 31 (USB_MAXCHILDREN) ports under a roothub.
The xHCI driver keeps track of which ports are suspended, which ports have
a suspend change bit set, and what time the port will be done resuming.
It keeps track of the first two by setting a bit in a u32 variable,
suspended_ports or port_c_suspend.  The xHCI driver currently assumes we
can have up to 256 ports under a roothub, so it allocates an array of 8
u32 variables for both suspended_ports and port_c_suspend.  It also
allocates a 256-element array to keep track of when the ports will be done
resuming.

Since we can only have 31 roothub ports, we only need to use one u32 for
each of the suspend state and change variables.  We simplify the bit math
that's trying to index into those arrays and set the correct bit, if we
assume wIndex never exceeds 30.  (wIndex is zero-based after it's
decremented from the value passed in from the USB core.)  Finally, we
change the resume_done array to only hold 31 elements.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Andiry Xu <andiry.xu@amd.com>

Using a #define to redefine a common variable name is a bad thing,
especially when the #define is in a header.  include/linux/usb/hcd.h
redefined bitmap to DeviceRemovable to avoid typing a long field in the
hub descriptor.  This has unintended side effects for files like
drivers/usb/core/devio.c that include that file, since another header
included after hcd.h has different variables named bitmap.

Remove the bitmap #define and replace instances of it in the host
controller code.  Cleanup the spaces around function calls and square
brackets while we're at it.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: Tony Olech <tony.olech@elandigitalsystems.com>
Cc: "Robert P. J. Day" <rpjday@crashcourse.ca>
Cc: Max Vozeler <mvz@vozeler.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Rodolfo Giometti <giometti@linux.it>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Anton Vorontsov <avorontsov@mvista.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Lothar Wassmann <LW@KARO-electronics.de>
Cc: Olav Kongas <ok@artecdesign.ee>
Cc: Martin Fuzzey <mfuzzey@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <dbrownell@users.sourceforge.net>

The test of placing a number of command no-ops on the command ring and
counting the number of no-op events that were generated was only used
during the initial xHCI driver bring up.  This test is no longer used, so
delete it.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

The Tegra2 USB controller doesn't properly deal with misaligned DMA
buffers, causing corruption.  This is especially prevalent with USB
network adapters, where skbuff alignment is often in the middle of a
4-byte dword.

To avoid this, allocate a temporary buffer for the DMA if the provided
buffer isn't sufficiently aligned.
Signed-off-by: NRobert Morell <rmorell@nvidia.com>
Signed-off-by: NBenoit Goby <benoit@android.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The Tegra 2 SoC has 3 EHCI compatible USB controllers. This patch adds
the necessary glue to allow the ehci-hcd driver to work on Tegra 2
SoCs.

The platform data is used to configure board-specific phy settings and
to configure the operating mode, as one of the ports may be used as a otg
port. For additional power saving, the driver supports powering down the
phy on bus suspend when it is used, for example, to connect an internal
device that use an out-of-band remote wakeup mechanism (e.g. a gpio).
Signed-off-by: NBenoit Goby <benoit@android.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix the following section mismatch warning:

WARNING: drivers/usb/built-in.o(.data+0x74c): Section mismatch in reference from the variable ehci_atmel_driver to the function .init.text:ehci_atmel_drv_probe()
The variable ehci_atmel_driver references
the function __init ehci_atmel_drv_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Signed-off-by: NHubert Feurstein <h.feurstein@gmail.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Commit ab1666c1 (USB: quirk PLL power down mode)
added code that reads the revision ID from the PCI configuration register while
it's stored by PCI subsystem in the 'revision' field of 'struct pci_dev'...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This driver is used across all MSM SoCs.  Hence give a generic name.
All Functions and strutures are also using "msm_otg" as prefix.
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This fixes a problem with my previous patch series where there's a great
risk that the kernel will crash when unplugging interrupt devices from
the USB port. These lines must have got missing when I rebased the
patches from the older kernel I was working with to 2.6.37 and 2.6-next:

This fixes a bug where the kernel may crash if you unplug a USB device
that has active interrupt transfers.
Signed-off-by: NArvid Brodin <arvid.brodin@enea.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Build log:
In file included from drivers/usb/host/ehci-hcd.c:1208:
drivers/usb/host/ehci-xilinx-of.c: In function 'ehci_hcd_xilinx_of_probe':
drivers/usb/host/ehci-xilinx-of.c:168: error: implicit declaration of function 'of_address_to_resource'
Signed-off-by: NJohn Williams <john.williams@petalogix.com>
Signed-off-by: NMichal Simek <monstr@monstr.eu>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The SH EHCI/OHCI driver hardcoded the CPU type in {ehci,ohci}-hcd.c.
So if we will add the new CPU, we had to add to the hcd driver each time.
The patch adds the CONFIG_USB_{EHCI,OHCI}_SH configuration. So if we
want to use the SH EHCI/OHCI, we only enable the configuration.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>