Extend the OCP_* register offsets in the struct
omap_hwmod_class_sysconfig to 32 bits.  This is required to add the
OMAP4+ GPU hwmod, which uses OCP_* register offsets larger than 16
bits.

Another possible solution may be to simply add a single 16 bit offset
field in this structure, and to add code to factor that offset into
all OCP_* register accesses.  This would save some memory, since
almost no modules need 32 bit offsets.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>

One of the OMAP4 links was missing OCP_USER flags, since it was only
used by the DSP initiator, and we did not have an OCP_USER_DSP flag.
Future patches will switch the hwmod code and data to register
interfaces, rather than hwmods, and it will be mandatory for all
interfaces to have at least one user bit set.  This patch resolves the
issue by adding OCP_USER_DSP and marking the DSP-IVA interface
appropriately.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>

The timer integration code pokes around in hwmod data structures.
Those data structures are about to change.  Define a function,
omap_hwmod_get_resource_byname(), for the timer integration code to
use instead.

The original patch has been changed to use struct resource by Tony's
request, although the caller of this function should not be a driver._
Platform drivers should get their data through the regular platform_*
functions; DT drivers through the appropriate of_* functions.  This a
function is only for use by OMAP core code in arch/arm/*omap*.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>

Due to HW limitation, some IPs should not be accessed just after a
softreset. Since the current hwmod sequence is accessing the sysconfig
register just after the reset, it might lead to OCP bus error in
that case.

Add a new field in the sysconfig structure to specify a delay in usecs
needed after doing a softreset.

In the case of the ISS and FDIF modules, the L3 OCP port will be
disconnected upon a SW reset. That issue was confirmed with HW simulation
and an errata should be available soon. The HW recommendation to avoid
that is to wait for 100 OCP clk cycles, before accessing the IP.

Considering the worse case (OPP50), the L3 bus will run at 100 MHz,
so a 1 usec delay is needed. Add an x2 margin to be safe.
Acked-by: NBenoit Cousson <b-cousson@ti.com>
Signed-off-by: NFernando Guzman Lugo <fernando.lugo@ti.com>
[paul@pwsan.com: dropped FDIF change for now since the hwmod data is not
 yet upstream; the FDIF change will need to be added later once the FDIF
 data is merged]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

In the SYSC_TYPE1_XXX_MASK configuration, SYSC_XXX_SHIFT macro
is used which is not defined anywhere in the kernel.
Until now the build was going through successfully, since it
is not being used anywhere in kernel.

This bug got introduced by the commit
358f0e63 ("OMAP3: hwmod: support
to specify the offset position of various SYSCONFIG register bits.")
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Acked-by: NBenoit Cousson <b-cousson@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

To set sr ntarget values for all volt_domain,
volt_table is retrieved by doing a look_up of 'vdd_name'
field from omap_hwmod but voltage domain pointer does not
belong to omap_hwmod and is not used anywhere else.
As a part of voltage layer and SR Layer clean up volt
pointer is removed from omap_hwmod and added in dev
attributes of SR. The value of the field must match
the voltage domain names for the binding to be effective.

Tested on OMAP3630 SDP, OMAP3530 Beagleboard and
OMAP4430 SDP Board.
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NShweta Gulati <shweta.gulati@ti.com>
Acked by: Nishanth Menon <nm@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: NJean Pihet <j-pihet@ti.com>
Reviewed-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

An hwmod with a 'HWMOD_INIT_NO_IDLE' flag set, is left in
enabled state by the hwmod framework post the initial setup.
Once a real user of the device (a driver) tries to enable it
at a later point, the hwmod framework throws a WARN() about
the device being already in enabled state.

Fix this by introducing a new internal flag '_HWMOD_SKIP_ENABLE' to
identify such devices/hwmods. When the device/hwmod is requested to be
enabled (the first time) by its driver/user, nothing except the
mux-enable is needed. The mux data is board specific and is
unavailable during initial enable() of the device, done by the
framework as part of setup().

A good example of a such a device is an UART used as debug console.
The UART module needs to be kept enabled through the boot, until the
UART driver takes control of it, for debug prints to appear on
the console.
Acked-by: NKevin Hilman <khilman@ti.com>
Acked-by: NBenoit Cousson <b-cousson@ti.com>
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: use a flag rather than a state; updated commit message;
 edited some documentation]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

By default all registered pads will trigger mpu_irqs[0]. Now there is
an API for selecting used mpu_irq on pad basis, which can be used to
trigger different irq handlers for different pads in the same hwmod.
Each pad that requires its interrupt to be re-routed this way must
have a separate call to omap_hwmod_pad_route_irq(hwmod, pad, irq).
Signed-off-by: NTero Kristo <t-kristo@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Tested-by: NKevin Hilman <khilman@ti.com>
Reviewed-by: NKevin Hilman <khilman@ti.com>
[paul@pwsan.com: moved fn to omap_hwmod.c; separated fn from mux scan_wakeups
 changes; added kerneldoc]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

OMAP mux now parses active wakeup events from pad registers and calls
corresponding hwmod ISRs once a wakeup is detected. This is
accomplished by registering an interrupt handler for PRCM IO event,
which is raised every time the HW detects wakeups.

[paul@pwsan.com: This patch is a merge of Govindraj R's "ARM: OMAP2+:
hwmod: Add API to check IO PAD wakeup status" patch, Tero Kristo's
"ARM: OMAP2+: mux: add support for PAD wakeup interrupts" patch, and
part of Tero's "ARM: OMAP: mux: add support for selecting mpu_irq for
each wakeup pad" patch.]
Signed-off-by: NTero Kristo <t-kristo@ti.com>
Cc: Govindraj.R <govindraj.raja@ti.com>
Tested-by: NKevin Hilman <khilman@ti.com>
Reviewed-by: NKevin Hilman <khilman@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
[paul@pwsan.com: reduced indentation level; renamed omap_hwmod function;
 improved function documentation; modified to iterate only through dynamic
 pads; modified to skip pads where idle mode doesn't enable wakeups; split
 patches]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

get_context_loss_count functions return context loss count as u32, and
zero means an error. However, zero is also returned when context has
never been lost and could also be returned when the context loss count
has wrapped and goes to zero.

Change the functions to return an int, with negative value meaning an
error.

OMAP HSMMC code uses omap_pm_get_dev_context_loss_count(), but as the
hsmmc code handles the returned value as an int, with negative value
meaning an error, this patch actually fixes hsmmc code also.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NKevin Hilman <khilman@ti.com>
Acked-by: NPaul Walmsley <paul@pwsan.com>
[tony@atomide.com: updated to fix a warning with recent dmtimer changes]
Signed-off-by: NTony Lindgren <tony@atomide.com>

The voltage domain pointer currently in struct omap_hwmod is not used
and does not belong here.  Instead, voltage domains will be associated
with powerdomains in forthcoming patches.
Acked-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

At Tony's request, remove the OMAP_CHIP* flags from the hwmod data, and
replace it instead with chip family, variant, and ES level-specific lists
of hwmods to register.

Thanks to Gražvydas Ignotas <notasas@gmail.com> for finding a bug in the
AM3517/3505 support, and for other review comments.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Gražvydas Ignotas <notasas@gmail.com>

Add a new field to provide the mode supported by the module.
The mode will control the way mandatory clocks are managed by the PRCM.

  0 : Module is temporarily disabled by SW. OCP access to module are stalled.
      Can be used to change timing parameter of GPMC module.
  1 : Module is managed automatically by HW according to clock domain
      transition. A clock domain sleep transition put module into idle.
      A wakeup domain transition put it back into function.
      If CLKTRCTRL=3, any OCP access to module is always granted.
      Module clocks may be gated according to the clock domain state.
  2 : Module is explicitly enabled. Interface clock (if not used for
      functions) may be gated according to the clock domain state.
      Functional clocks are guarantied to stay present. As long as
      in this configuration, power domain sleep transition cannot happen.

Some modules will have a modulemode initialized at 1 (HWCTRL) by default.
This is the case for interconnect and simple module like GPIO, WDT, MAILBOX.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Add a 'context_offs' entry in the prcm.omap4 structure to all
IPs when applicable.
The offset will be used to retrieve the per module context lost
information now available on OMAP4.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

The RSTCTRL register was accessed using an absolute address.
The usage of hardcoded macros to calculate virtual address from physical
one should be avoided as much as possible.
The usage of an offset will allow future improvement like migration from
the current architecture code toward a module driver.

Update prm_xxx accessors, move definition to the proper header file and
update copyrights.
Change the s16 register offset parameter to u16.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: use '_prminst_' in function names that are part of the
 prminst44xx.c file]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

The CLKCTRL register was accessed using an absolute address.
The usage of hardcoded macros to calculate virtual address from physical
one should be avoided as much as possible.
The usage of a offset will allow future improvement like migration from
the current architecture code toward a module driver.

Update cm_xxx accessor, move definition to the proper header file and
update copyrights.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Todd Poynor <toddpoynor@google.com>
[paul@pwsan.com: renamed 'omap4_cm_' fns to 'omap4_cminst_'; removed empty
 fn prototype section from cm44xx.h; incorporated comments from Todd;
 documented some functions]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

At boot time, lookup the clkdm_name to get the clkdm
structure pointer for further usage.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

In OMAP PRCM terminology, the clock domain is defined as a group of IPs
that share some clocks and most of the time an interface clock.
Every IP does belong to a clockdomain.
For the moment the clock domain attribute is affected to a clock node.
The issue with that approach, is that a clock might or not belong to a
clock domain. Moreover during module transition, it is up to a module
to handle properly the clock domain state and not to a clock node.

Create a clkdm_name attribute to provide this information per hwmod.

Populate this attribute for every OMAP4 hwmod entries.

Future cleanup series with remove that information from the OMAP4 clock
when it is relevant.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: fix the mpuss_clkdm name]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

The sequence of _ocp_softreset doesn't work for i2c. The i2c module has a
special sequence to reset the module. The sequence is
 - Disable the I2C.
 - Write to SOFTRESET bit.
 - Enable the I2C.
 - Poll on the RESETDONE bit.
The sequence is implemented as a function and the i2c_class is updated with
the correct 'reset' pointer.  omap_hwmod_softreset function is implemented
which triggers the softreset by writing into sysconfig register. On following
this sequence, i2c module resets properly and timeouts are not seen.

Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: NAvinash.H.M <avinashhm@ti.com>
[paul@pwsan.com: combined this patch with a patch to remove
 HWMOD_INIT_NO_RESET from the 44xx hwmod flags; change register
 offset conditional code to use the IP block revision; minor code
 cleanup]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Previously, struct omap_hwmod_dma_info arrays were unterminated; and
users of these arrays used the ARRAY_SIZE() macro to determine the
length of the array.  However, ARRAY_SIZE() only works when the array
is in the same scope as the macro user.

So far this hasn't been a problem.  However, to reduce duplicated
data, a subsequent patch will move common data to a separate, shared
file.  When this is done, ARRAY_SIZE() will no longer be usable.

This patch removes ARRAY_SIZE() usage for struct omap_hwmod_dma_info
arrays and uses a sentinel value (irq == -1) as the array terminator
instead.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Previously, struct omap_hwmod_mpu_irqs arrays were unterminated; and
users of these arrays used the ARRAY_SIZE() macro to determine the
length of the array.  However, ARRAY_SIZE() only works when the array
is in the same scope as the macro user.

So far this hasn't been a problem.  However, to reduce duplicated
data, a subsequent patch will move common data to a separate, shared
file.  When this is done, ARRAY_SIZE() will no longer be usable.

This patch removes ARRAY_SIZE() usage for struct omap_hwmod_mpu_irqs
arrays and uses a sentinel value (irq == -1) as the array terminator
instead.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Previously, struct omap_hwmod_addr_space arrays were unterminated; and
users of these arrays used the ARRAY_SIZE() macro to determine the
length of the array.  However, ARRAY_SIZE() only works when the array
is in the same scope as the macro user.

So far this hasn't been a problem.  However, to reduce duplicated
data, a subsequent patch will move common data to a separate, shared
file.  When this is done, ARRAY_SIZE() will no longer be usable.

This patch removes ARRAY_SIZE() usage for struct omap_hwmod_addr_space
arrays and uses a null structure member as the array terminator
instead.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

The commit 86009eb3 was adding
the wakeup support for new OMAP4 IPs. This support is incomplete for
busmaster IPs that need as well to use smart-standby with wakeup.

This new standbymode is suported on HSI and USB_HOST_FS for the moment.

Add the new MSTANDBY_SMART_WKUP flag to mark the IPs that support this
capability.

Enable this new mode when applicable in _enable_wakeup, _disable_wakeup,
_enable_sysc and _idle_sysc.

The omap_hwmod_44xx_data.c will have to be updated to add this new flag.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Signed-off-by: NDjamil Elaidi <d-elaidi@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

This avoids going through the list unnecessarily when
idling devices for runtime PM.

Based on an earlier patch by sricharan <r.sricharan@ti.com>.
Signed-off-by: Nsricharan <r.sricharan@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Create a new API that forms a wrapper to _set_module_autoidle()
to modify the AUTOIDLE bit.

This API is intended to be used by drivers that requires direct
manipulation of the AUTOIDLE bits in SYSCONFIG register.
McBSP driver requires autoidle bit to be enabled/disabled while
using sidetone feature.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: restrict the hwmod states that the autoidle bit can be changed
 in; changed function name; dropped "int" from "unsigned int long"]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Some boards can't tolerate IP blocks being reset when they are initialized.
Michael Büsch cites a case with the Nokia N810:

    http://www.spinics.net/lists/linux-omap/msg47277.html

To allow such boards to continue working normally, allow board file
maintainers to mark IP blocks to prevent them from being reset upon
init.  This is done via a hwmod function, omap_hwmod_no_setup_reset().
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Michael Buesch <mb@bu3sch.de>

On OMAP2 and OMAP3 the reset ctrl shift doesn't match the
status bit, as it does on OMAP4, when handling the reset lines.

This patch adds a new member in the reset info structure, so now it
can be added as part of hwmod data, and checked accordingly for
OMAP2 or 3; otherwise, there could be cases when the shift masks
doesn't match both of the registers, and a successful reset might
throw an error message or vice versa.
Signed-off-by: NOmar Ramirez Luna <omar.ramirez@ti.com>
[paul@pwsan.com: added a warning if st_shift used on OMAP4; renamed 'r'
 variable; improved some documentation]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

The documented name of the HWMOD_NO_OCP_AUTOIDLE flag was incorrect; fix it.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

At this point in time, there's no reason for this header file to be in
plat-omap/include/plat/voltage.h.  It should not be included by device
drivers, and the code that uses it is currently all under mach-omap2/.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Add omap_hwmod_setup_one(), which is intended for use early in boot to
selectively setup the hwmods needed for system clocksources and
clockevents, and any other hwmod that is needed in early boot.
omap_hwmod_setup_all() can then be called later in the boot process.
The point is to minimize the amount of code that needs to be run
early.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Tony Lindgren <tony@atomide.com>

Rename omap_hwmod_init() to omap_hwmod_register().  Rename
omap_hwmod_late_init() to omap_hwmod_setup_all().  Also change all of
the callers to reflect the new names.  While here, update some
copyrights.

Suggested by Tony Lindgren <tony@atomide.com>.

N.B. The comment in mach-omap2/serial.c may no longer be correct, given
     recent changes in init order.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>

Adds support for resource API to get address space info other than just MPU.
The drivers can now use platform_get_resource_byname() to get resource of
type 'IORESOURCE_MEM' by name.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Acked-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Otherwise things will fail with early_init changes.
Signed-off-by: NTony Lindgren <tony@atomide.com>

This allows adding hwmod specific pads dynamically during the
platform device init.

Note that we don't currently have the hwmod specific signals
listed in the hwmod data, but struct omap_hwmod_mux_info will
make that possible if necessary.
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch extends the device hwmod structure to contain
info about the voltage domain to which the device belongs to.
This is needed to support a device based DVFS where the
device knows which voltage domain it belongs to.
Signed-off-by: NThara Gopinath <thara@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Implement OMAP PM layer omap_pm_get_dev_context_loss_count() API by
creating similar APIs at the omap_device and omap_hwmod levels.  The
omap_hwmod level call is the layer with access to the powerdomain
core, so it is the place where the powerdomain is queried to get the
context loss count.

The new APIs return an unsigned value that can wrap as the
context-loss count grows.  However, the wrapping is not important as
the role of this function is to determine context loss by checking for
any difference in subsequent calls to this function.

Note that these APIs at each level can return zero when no context
loss is detected, or on errors.  This is to avoid returning error
codes which could potentially be mistaken for large context loss
counters.

NOTE: only works for devices which have been converted to use
      omap_device/omap_hwmod.

Longer term, we could possibly remove this API from the OMAP PM layer,
and instead directly use the omap_device level API.
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

The new OMAP4 IPs introduced a new idle mode named smart-idle with wakeup.

This new idlemode replaces the enawakeup for the new IPs but seems to
coexist as well for some legacy IPs (UART, GPIO, MCSPI...)

Add the new SIDLE_SMART_WKUP flag to mark the IPs that support this
capability.
The omap_hwmod_44xx_data.c will have to be updated to add this new flag.

Enable this new mode when applicable in _enable_wakeup, _enable_sysc and
_idle_sysc.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Tested-by: NSebastien Guiriec <s-guiriec@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>

Do not allow omap_hwmod_register to be used outside the core
hwmod code. An omap_hwmod should be registered only at init time.
Remove the omap_hwmod_unregister that is not used today since the
hwmod list will be built once at init time and never be modified
at runtime.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>

Trivial cleanup and documentation changes on the hwmod code and data:

- add some hwmod documentation to indicate flags that should be moved
  outside the static hwmod data in a future patch

- remove some unused fields in the struct omap_hwmod_ocp_if and
  struct omap_hwmod structures
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>

Change the per-hwmod mutex to a spinlock.  (The per-hwmod lock
serializes most post-initialization hwmod operations such as enable,
idle, and shutdown.)  Spinlocks are needed, because in some cases,
hwmods must be enabled from timer interrupt disabled-context, such as
an ISR.  The current use-case that is driving this is the OMAP GPIO
block ISR: it can trigger interrupts even with its clocks disabled,
but these clocks are needed for register accesses in the ISR to succeed.

This patch also effectively reverts commit
84824022 - this patch makes
_omap_hwmod_enable() and _omap_hwmod_init() static, renames them back
to _enable() and _idle(), and changes their callers to call the
spinlocking versions.  Previously, since omap_hwmod_{enable,init}()
attempted to take mutexes, these functions could not be called while
the timer interrupt was disabled; but now that the functions use
spinlocks and save and restore the IRQ state, it is appropriate to
call them directly.

Kevin Hilman <khilman@deeprootsystems.com> originally proposed this
patch - thanks Kevin.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Benoît Cousson <b-cousson@ti.com>