Extend the OCP_* register offsets in the struct
omap_hwmod_class_sysconfig to 32 bits.  This is required to add the
OMAP4+ GPU hwmod, which uses OCP_* register offsets larger than 16
bits.

Another possible solution may be to simply add a single 16 bit offset
field in this structure, and to add code to factor that offset into
all OCP_* register accesses.  This would save some memory, since
almost no modules need 32 bit offsets.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>

One of the OMAP4 links was missing OCP_USER flags, since it was only
used by the DSP initiator, and we did not have an OCP_USER_DSP flag.
Future patches will switch the hwmod code and data to register
interfaces, rather than hwmods, and it will be mandatory for all
interfaces to have at least one user bit set.  This patch resolves the
issue by adding OCP_USER_DSP and marking the DSP-IVA interface
appropriately.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>

The timer integration code pokes around in hwmod data structures.
Those data structures are about to change.  Define a function,
omap_hwmod_get_resource_byname(), for the timer integration code to
use instead.

The original patch has been changed to use struct resource by Tony's
request, although the caller of this function should not be a driver._
Platform drivers should get their data through the regular platform_*
functions; DT drivers through the appropriate of_* functions.  This a
function is only for use by OMAP core code in arch/arm/*omap*.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>

Due to HW limitation, some IPs should not be accessed just after a
softreset. Since the current hwmod sequence is accessing the sysconfig
register just after the reset, it might lead to OCP bus error in
that case.

Add a new field in the sysconfig structure to specify a delay in usecs
needed after doing a softreset.

In the case of the ISS and FDIF modules, the L3 OCP port will be
disconnected upon a SW reset. That issue was confirmed with HW simulation
and an errata should be available soon. The HW recommendation to avoid
that is to wait for 100 OCP clk cycles, before accessing the IP.

Considering the worse case (OPP50), the L3 bus will run at 100 MHz,
so a 1 usec delay is needed. Add an x2 margin to be safe.
Acked-by: NBenoit Cousson <b-cousson@ti.com>
Signed-off-by: NFernando Guzman Lugo <fernando.lugo@ti.com>
[paul@pwsan.com: dropped FDIF change for now since the hwmod data is not
 yet upstream; the FDIF change will need to be added later once the FDIF
 data is merged]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

With commit c334bc15 (ARM: make mach/io.h include optional), PCMCIA was
broken. PCMCIA depends on __io() returning a valid i/o address, and most
ARM platforms require IO_SPACE_LIMIT be set to 0xffffffff for PCMCIA. This
needs a better fix with a fixed i/o address mapping, but for now we just
restore things to the previous behavior.

This fixes at91, omap1, pxa and sa11xx. pxa needs io.h if PCI is enabled,
but PCMCIA is not. sa11xx already has IO_SPACE_LIMIT set to 0xffffffff,
so it doesn't need an io.h.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Cc: Joachim Eastwood <joachim.eastwood@jotron.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Tested-by: Paul Parsons <lost.distance@yahoo.com> (pxa270)
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

In the SYSC_TYPE1_XXX_MASK configuration, SYSC_XXX_SHIFT macro
is used which is not defined anywhere in the kernel.
Until now the build was going through successfully, since it
is not being used anywhere in kernel.

This bug got introduced by the commit
358f0e63 ("OMAP3: hwmod: support
to specify the offset position of various SYSCONFIG register bits.")
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Acked-by: NBenoit Cousson <b-cousson@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

clk_disable_unused is invoked when CONFIG_OMAP_RESET_CLOCKS=y.
Since clk_disable_unused is called as lateinitcall, there can
be more than a few workqueues executing off secondary CPU(s).
The current code does the following:
a) checks if clk is unused
b) holds lock
c) disables clk
d) unlocks

Between (a) and (b) being executed on CPU0, It is possible to
have a driver executing on CPU1 which could do a get_sync->clk_get
(and increase the use_count) of the clock which was just about
to be disabled by clk_disable_unused.

We ensure instead that the entire list traversal is protected by
the lock allowing for parent child clock traversal which could be
potentially be done by runtime operations to be safe as well.
Reported-by: NTodd Poynor <toddpoynor@google.com>
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Since all references to OMAP_GPIO_IRQ macro are replaced now
with gpio_to_irq(), this can be removed altogether.
Signed-off-by: NTarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Disintegrate asm/system.h for ARM.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
cc: Russell King <linux@arm.linux.org.uk>
cc: linux-arm-kernel@lists.infradead.org

set_sleep seems to be unused in omap_hsmmc driver. so get rid of it.
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Tested-by: NVenkatraman S <svenkatr@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch allows us to drop the OMAP dependency from the OMAP4 keypad
driver.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Several platforms create IOMEM defines for casting to 'void __iomem *',
and other platforms are incorrectly using __io() macro for the same
purpose. This creates a common definition and removes all the platform
specific versions. Rather than try to make linux/io.h and asm/io.h
assembly safe, the assembly version of IOMEM is moved into
asm/assembler.h.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Acked-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ryan Mallon <rmallon@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: NDavid Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Acked-by: NTony Lindgren <tony@atomide.com>
Acked-by: NPaul Walmsley <paul@pwsan.com>
Acked-by: NViresh Kumar <viresh.kumar@st.com>
Cc: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Cc: Colin Cross <ccross@android.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Stephen Warren <swarren@nvidia.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>

Clock signal muxing, and functional clock related defines are only needed
in ASoC drivers.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NJarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: NMark Brown <broonoie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@ti.com>

The driver for omap-mcbsp-dai no longer exist since it has been merged with
the omap-mcbsp driver.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Tested-by: NGrazvydas Ignotas <notasas@gmail.com>
Tested-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: NJarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: NLiam Girdwood <lrg@ti.com>

The OMAP McBSP driver stack used to contain two different
drivers. One of them was used as kind low-level access to
the IP, while the other driver was the ASoC DAI driver.
There were global, shared structures, in different places,
the McBSP instances are reffered with id numbers (sometimes
0 based, in other cases 1 based id numbers).

Create one single driver for OMAP McBSP with name: omap-mcbsp.
Convert the old omap-mcbsp driver initially to be a library
for the omap-mcbsp DAI driver. With this change we can get rid
of all global variables, structures.

Further cleanup is coming...
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: NGrazvydas Ignotas <notasas@gmail.com>
Tested-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NJarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: NLiam Girdwood <lrg@ti.com>

Move most of the content of the plat/mcbsp.h header file under
sound/soc/omap/ to help further cleanups.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: NGrazvydas Ignotas <notasas@gmail.com>
Tested-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NJarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: NLiam Girdwood <lrg@ti.com>

In order to consolidate the McBSP driver move it out from
arch/arm/plat-omap directory under sound/soc/omap/
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Tested-by: NGrazvydas Ignotas <notasas@gmail.com>
Tested-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: NJarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: NLiam Girdwood <lrg@ti.com>

Convert the plat-omap/mcbsp.c driver to be proper platform driver.
Remove the omap_mcbsp_init function call which was called from
mach-omap1/2/mcbsp.c to register the platform driver for the just
created platform device in the same function.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Tested-by: NGrazvydas Ignotas <notasas@gmail.com>
Tested-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: NJarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: NLiam Girdwood <lrg@ti.com>

Otherwise we will get:

arch/arm/plat-omap/fb.c:101: error: expected ‘)’ before ‘*’ token
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

These are no longer needed with the recent iomap.h
changes.
Reported-by: NRob Herring <robherring2@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>

Trivial whitespace fix
Signed-off-by: NFelipe Contreras <felipe.contreras@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The definition cpu_is_omap4430() always returns 0 even when CONFIG_ARCH_OMAP4
is enabled. This macro should be removed and the macro cpu_is_omap443x() should
be used where needed for OMAP4430 devices.
Signed-off-by: NJon Hunter <jon-hunter@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

arch/arm/plat-omap/clock.c: included 'linux/debugfs.h' twice,
remove the duplicate.
Signed-off-by: NDanny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Update SRAM start & size for am33xx SoC's.

Note: cpu_is_34xx() is true for am33xx also. Doing
cpu_is_am33xx() check after cpu_is_34xx() will not
achieve what we want due to the above reason.
Hence cpu_is_am33xx() is done before cpu_is_34xx()
Signed-off-by: NVaibhav Bedia <vaibhav.bedia@ti.com>
Signed-off-by: NAfzal Mohammed <afzal@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Since omap_dm_timer_write_reg/__omap_dm_timer_write is now modified
to use timer->func_base OCP_CFG should not use this wrapper anymore.
Instead use __raw_writel() directly and use timer->io_base instead
to write to OCP_CFG.

The timer->sys_stat is valid only if timer->revision is 1. In the
context restore function make this correction.

Save the contexts and loss count when timer is stopped.
Also, disable the clock. Else, clock usecount would become imbalanced.
Signed-off-by: NTarun Kanti DebBarma <tarun.kanti@ti.com>
Tested-by: NOmar Ramirez Luna <omar.ramirez@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

ARM: OMAP2+: omap_device: call all suspend, resume callbacks when OMAP_DEVICE_NO_IDLE_ON_SUSPEND is set

During system suspend, when OMAP_DEVICE_NO_IDLE_ON_SUSPEND is set on
an omap_device, call the corresponding driver's ->suspend() and
->suspend_noirq() callbacks (if present).  Similarly, during resume,
the driver's ->resume() and ->resume_noirq() callbacks must both be
called, if present.  (The previous code only called ->suspend_noirq()
and ->resume_noirq().)

If all of these callbacks aren't called, some important driver
suspend/resume code may not get executed.

In current mainline, the bug fixed by this patch is only a problem
under the following conditions:

- the kernel is running on an OMAP4

- an OMAP UART is used as a console

- the kernel command line parameter 'no_console_suspend' is specified

- and the system enters suspend ("echo mem > /sys/power/state").

Under this combined circumstance, the system cannot be awakened via
the serial port after commit be4b0281c
("tty: serial: OMAP: block idle while the UART is transferring data in
PIO mode").  This is because the OMAP UART driver's ->suspend()
callback is never called.  The ->suspend() callback would have called
uart_suspend_port() which in turn would call enable_irq_wake().  Since
enable_irq_wake() isn't called for the UART's IRQ, check_wakeup_irqs()
would mask off the UART IRQ in the GIC.

On v3.3 kernels prior to the above commit, serial resume from suspend
presumably occurred via the PRCM interrupt.  The UART was in
smart-idle mode, so it was able to send a PRCM wakeup which in turn
would be converted into a PRCM interrupt to the GIC, waking up the
kernel.  But after the above commit, when the system is suspended in
the middle of a UART transmit, the UART IP block would be in no-idle
mode.  In no-idle mode, the UART won't generate wakeups to the PRCM
when incoming characters are received; only GIC interrupts.  But since
the UART driver's ->suspend() callback is never called,
uart_suspend_port() and enable_irq_wake() is never called; so the UART
interrupt is masked by check_wakeup_irqs() and the UART can't wake up
the MPU.

The remaining mechanism that could have awakened the system would have
been I/O chain wakeups.  These wouldn't be active because the console
UART's clocks are never disabled when no_console_suspend is used,
preventing the full chip from idling.  Also, current mainline doesn't
yet support full chip idle states for OMAP4, so I/O chain wakeups are
not enabled.

This patch is the result of a collaboration.  John Stultz
<johnstul@us.ibm.com> and Andy Green <andy.green@linaro.org> reported
the serial wakeup problem that led to the discovery of this problem.
Kevin Hilman <khilman@ti.com> narrowed the problem down to the use of
no_console_suspend.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Andy Green <andy.green@linaro.org>
Reviewed-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

Currently all omap_devices are forced to have the dummy device
'omap_device_parent' as a parent.  This was used to distinguish
omap_devices from "normal" platform_devices in the OMAP PM core code.

Now that we implement the PM core using PM domains, this is no longer
needed, and is removed.

This also frees up omap_devices to have a more complex parent/child
relationships that model actual device relationships.

The only in-tree user of omap_device_parent was the OMAP PM layer to
handle lost-context count for omap_devices.  That is now converted to
use the presence of the omap_device_pm_domain instead.
Signed-off-by: NKevin Hilman <khilman@ti.com>

The driver is still relying on internal OMAP IRQ defines that
are not relevant anymore if OMAP is built with SPARSE_IRQ.

Replace the defines with the proper IRQ base number.
Clean some comment style issue.
Remove some hidden and ugly cpu_class_is_omap1() inside the
gpio header.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Tested-by: NTarun Kanti DebBarma <tarun.kanti@ti.com>

To set sr ntarget values for all volt_domain,
volt_table is retrieved by doing a look_up of 'vdd_name'
field from omap_hwmod but voltage domain pointer does not
belong to omap_hwmod and is not used anywhere else.
As a part of voltage layer and SR Layer clean up volt
pointer is removed from omap_hwmod and added in dev
attributes of SR. The value of the field must match
the voltage domain names for the binding to be effective.

Tested on OMAP3630 SDP, OMAP3530 Beagleboard and
OMAP4430 SDP Board.
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NShweta Gulati <shweta.gulati@ti.com>
Acked by: Nishanth Menon <nm@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: NJean Pihet <j-pihet@ti.com>
Reviewed-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

This functionality has already been implemented in the cx20442 codec
driver (commit f75a8ff6, "ASoC: cx20442:
add bias control over a platform provided regulator"), no need to keep
it here duplicated.

Once done, remove the no longer used AMS_DELTA_LATCH2_MODEM_NRESET
symbol from the board header file and a call to the regulator_toggle()
helper function from the old API wrapper found in the board file.  While
being at it, simplify the way the modem .pm callback handles the
regulator and drop that helper function and its related consumer setup
completely.

Depends on patches 1/3 and 2/3 for clean apply and keep things working.
Signed-off-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add minimal support for Nokia RM-696 board.
Signed-off-by: NAaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The following commit: 2f31b516
Author: Tero Kristo <t-kristo@ti.com>
Date:   Fri Dec 16 14:37:00 2011 -0700

    ARM: OMAP4: PRM: use PRCM interrupt handler

introduced the PRCM interrupt handler and thus the need
for 64 more interrupts. Since SPARSE_IRQ is still not fully
functional on OMAP, the NR_IRQS needs to be updated to avoid
the failure that happen during irq_alloc_descs call inside
the PRCM driver:

[    0.208221] PRCM: failed to allocate irq descs: -12

Later the mux framework is then unable to request an IRQ from
the PRCM interrupt handler.

[    1.802795] mux: Failed to setup hwmod io irq -22

Fix that by adding 64 more interrupts for OMAP2PLUS config.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Building omap_devices should only be done at init time, and since
omap_device_build() is using early_platform calls which are also
__init, this ensures that omap_device isn't trying to use functions
that disappear.
Signed-off-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Drivers should no longer use omap_read/write functions
but instead use ioremap + read/write functions.

As some USB legacy code is still shared between omap1 and
omap2420, let's limit the omap_read/write to plat/usb.h.

Note that the long term fix is to update the drivers to
use ioremap and read/write functions. That can now be
done as a separate patch series that is limited to the
USB drivers.

Also make sure the legacy omap1-keypad.c driver builds
if selected for 2420 based systems.

Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This is needed to minimize io.h so the SoC specific io.h
for ARMs can removed.

Note that minimal driver changes for DSS and RNG are needed to
include cpu.h for SoC detection macros.

Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NTony Lindgren <tony@atomide.com>

There's no need to have these defines in plat/io.h.

Note that we now need to ifdef omap_read/write calls
as they will be available for omap1 only.

While at it, clean up the includes to group them like
they typically are grouped.
Signed-off-by: NTony Lindgren <tony@atomide.com>

There's no need to have these in plat/io.h.

While at it, clean up the includes to group them
like they typically are grouped.
Signed-off-by: NTony Lindgren <tony@atomide.com>

We don't want to keep it in io.h as we want to remove io.h
for omap2+ for the common zImage support.
Signed-off-by: NTony Lindgren <tony@atomide.com>

These should be local to omap2/3/4.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Flag single_channel in struct omap2_mcspi_device_config is not used
by drivers/spi/spi-omap2-mcspi.c so we may remove it from include/plat/mcspi.h
and affected board files.
Signed-off-by: NJarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>