Timeout of 20 seconds is too long for active wait performed
for 8051 command completion. It was required for scenarios
when transition to polling was requested before offline.quiet
state was reached. Currently wait for offline.quiet is
properly implemented and timeout can be reduced to 1 second.
Reviewed-by: NDean Luick <dean.luick@intel.com>
Reviewed-by: NDuane McCrory <duane.mccrory@intel.com>
Signed-off-by: NJakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Change serdes mode setting to use MISC_CONFIG_BITS in
VERIFY_CAP_LOCAL_LINK_WIDTH register. This method of
setting up serdes loopback is universally compatible
across all firmware versions.
Reviewed-by: NJakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: NJan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

When the link is disabled and re-enabled, the host version bit is not
set again, so the firmware behaves as though it’s interacting with an
old driver. This causes LNI to get out of sync. The host version bit
needs to be set at load_8051_firmware() and _dc_start(). Currently, it's
only set at load_8051_firmware().

Create a common function to set the bit with the intent to make the code
more maintainable in the future, set the host version bit at _dc_start()
and modify the 8051 command API to prevent a deadlock as _dc_start() is
already holding the dc8051 lock.

Fixes: 913cc671 ("IB/hfi1: Always perform offline transition")
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NSebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

QSFP reset enables AOC transmitters by default. They should be off
before moving to high power mode to complete the setup. There is no
need to reset the QSFP during LNI failure as it was reset at link down.
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: NJakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: NSebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Offline.quietDuration was added in the 8051 firmware, and the driver
only turns off the AOC transmitters when offline.quiet is reached.
However, the AOC transmitters need to be turned off at the new state.
Therefore, turn off the AOC transmitters at any offline substates
including offline.quiet and offline.quietDuration, then recheck we
reached offline.quiet to support backwards compatibility.
Reviewed-by: NJakub Byczkowski <jakub.byczkowski@intel.com>
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NSebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Do not track physical state separately from host_link_state.
Deduce physical state from host_link_state when required.
Change cache_physical_state to log_physical_state to make
sure host_link_state reflects hardwares physical state properly.
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NJakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Currently fallback configuration is loaded once per driver instance.
With multiple HFI devices in the same system the current code may not
load the platform config data for the device. Change fallback platform
config data loading to be per device.
Reviewed-by: NEaswar Hariharan <easwar.hariharan@intel.com>
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NJakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Do not track logical state separately from host_link_state. Deduce
logical state from host_link_state when required. Transitions in
set_link_state and goto_offline already make sure host_link_state
reflects hardware's logical state properly.
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NJakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Always initiate an offline transition request
when a link down occurs. The firmware will
use this request to confirm that the driver
has seen the link down message. A host version
is set to indicate this driver behavior to the
firmware.
Reviewed-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NSebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The hfi1_rcvctrl() function receives an index which it then converts
to an rcd.  Since most functions have the rcd, use that instead.
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: NSebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: NMichael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The hfi1_<set|clear>_ctxt_<j|p>key functions take a context index and
look up the context based on that index.

Since the context index is being retrieved from the context, this
doesn't seem optimal.

Pass the context pointer for use, rather than the context index.
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NMichael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The array index for the rcd array is sized several different ways
throughout the code.

Use the user interface size (u16) as the standard size and update the
necessary code to reflect this.

u16 is large enough for the largest amount of supported contexts.
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NMichael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

When the debugpat kernel boot flag is turned on the following
traces are printed:

[ 1884.793168] x86/PAT: Overlap at 0x90000000-0x92000000
[ 1884.803510] x86/PAT: reserve_memtype added [mem 0x91200000-0x9127ffff],
track uncached-minus, req write-combining, ret uncached-minus
[ 1884.818167] hfi1 0000:05:00.0: hfi1_0: WC Remapped RcvArray:
ffffc9000a980000

The ioremap_wc() clearly is not returning a write combining mapping due
to an overlap where the RcvArray is mapped in a uncached mapping prior
to creating the proposed write combining mapping.

The patch replaces the single base register for uncached CSRs that
used to overlap the RcvArray with two mappings.   One, kregbase1, from the
bar0 up to the RcvArray and another, kregbase2, from the end of the
RcvArray to the pio send buffer space.  A new dd field, base2_start,
is used to convert the zero-based offset in the CSR routines to the
correct kregbase1/kregbase2 mapping.  A single direct write of the
RcvArray CSRs is replaced with hfi1_put_tid() to insure correct access
using the new disjoint mapping.

Additionally, the kregend field is deleted since it is only ever written.

patdebug now shows the RcvArray as write combining:
[   35.688990] x86/PAT: reserve_memtype added [mem 0x91200000-0x9127ffff],
track write-combining, req write-combining, ret write-combining

To insulate from any potential issues with write combining, all
writeq are now flushed in hfi1_put_tid() and rcv_array_wc_fill().
Reviewed-by: NMitko Haralanov <mitko.haralanov@intel.com>
Reviewed-by: NAshutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Ensure states returned to the Fabric Manager are consistent with
the OPA specification by caching the physical state along with the
logical state.
Reviewed-by: NStuart Summers <john.s.summers@intel.com>
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Reviewed-by: NAndrzej Kotlowski <andrzej.kotlowski@intel.com>
Signed-off-by: NJakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

We move many common IB fields into the hfi1_packet structure and
set them up in a single function. This allows us to set the fields
in a single place and not deal with them throughout the driver.
Reviewed-by: NBrian Welty <brian.welty@intel.com>
Reviewed-by: NDasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDon Hiatt <don.hiatt@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Context initialization mixes base context init with sub context init.
This is bad because contexts can be reused, and on reuse, reinit things
that should not re-initialized.

Normalize comments and function names to refer to base context and
sub context (not main, shared or slaves).

Separate the base context initialization from sub context initialization.

hfi1_init_ctxt() cannot return an error so changed to a void and remove
error message.
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NMichael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

In the close path the context is removed from the device array, and then
the clear pkey function is called.  The pkey function trys to get the
context from the device array, but because it was removed the clearing
does not occur.

Rework pkey clear function to work as expected.  Update the function
variable to reflect the correct size and name of the hw_context.
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NMichael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

To improve the readability of function prototypes, give the parameters
names.
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NMichael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

HFI1 HW specific support for VNIC functionality.
Dynamically allocate a set of contexts for VNIC when the first vnic
port is instantiated. Allocate VNIC contexts from user contexts pool
and return them back to the same pool while freeing up. Set aside
enough MSI-X interrupts for VNIC contexts and assign them when the
contexts are allocated. On the receive side, use an RSM rule to
spread TCP/UDP streams among VNIC contexts.
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NNiranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Signed-off-by: NAndrzej Kacprowski <andrzej.kacprowski@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The HFI firmware now includes a patch level in its version.
Updating the necessary code to include the patch version in the
firmware string.
Reviewed-by: NEaswar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: NMichael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Set the status code BAD_L2 when unsupported type of packet
is received and dropped.
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NJakub Pawlak <jakub.pawlak@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

It was determined that 0x880 is a better value for hardware buffering,
use it.
Reviewed-by: NDean Luick <dean.luick@intel.com>
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NHarish Chegondi <harish.chegondi@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Add missing external device timeout notification.  Recognize
it as a failed LNI signal from the 8051 firmware.
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Use common header file structs, defines, and accessors
in the drivers.  The old declarations are removed.

The repositioning of the includes allows for the removal
of hfi1_message_header and replaces its use with ib_header.

Also corrected are two issues with set_armed_to_active():
- The "packet" parameter is now a pointer as it should have been
- The etype is validated to insure that the header is correct
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: NDon Hiatt <don.hiatt@intel.com>
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Sometimes a QSFP device does not respond in the expected time
after a power-on.  Add a read pre-check/retry when starting
the link on driver load.
Reviewed-by: NEaswar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Save the current capability state at user context creation
time.  Report this saved value for all shared contexts.

Also get rid of unnecessary hfi1_get_base_kinfo function.
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Read the version of the SBus, PCIe SerDes, and Fabric Serdes
firmwares at driver load time.
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Remove the TWSI code.  The driver now uses the kernel's built-in
i2c bit bus module.

Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: NEaswar Hariharan <easwar.hariharan@intel.com>
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Two 8051 link settings, external device config and tuning method,
were written in the wrong location and the previous settings were
not cleared.  For both, clear the old value and write the new
value.

Fixes: 8ebd4cf1 ("staging/rdma/hfi1: Add active and optical cable support")
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The TODO list for the hfi1 driver was completed during 4.6. In addition
other objections raised (which are far beyond what was in the TODO list)
have been addressed as well. It is now time to remove the driver from
staging and into the drivers/infiniband sub-tree.
Reviewed-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The 8051 uses a link down reason to inform the driver why the
link went down.  The neighbor planned link down reason code is
only valid when a link down idle message is received by the 8051.
Enhance the explanation on why the link went down.
Reviewed-by: NEaswar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Clock and data recovery mechanisms (CDRs) in active QSFP modules
can be turned on or off to improve the bit error rate observed on
the channel. Signal integrity and bit error rate requirements require
us to always turn on any CDRs present in low power cables (power
dissipation 2.5W or lower). However, we adhere to the platform
designer's settings (provided in the platform configuration) for
higher power cables (dissipation 3.5W or higher) if the platform
designer has determined that the platform requires the CDRs to be
turned on (or off) and is capable of supplying and cooling the higher
power modules.

This patch also introduces the get_qsfp_power_class function to
centralize the bit twiddling required to determine the QSFP power class
across the code. Reusing this function improves the readability of code
that depends on knowing the power class of the cable, such as the
active and optical channel tuning algorithm.
Reviewed-by: NDean Luick <dean.luick@intel.com>
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NEaswar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Host handshake timeout can occur during the verify capability
state. This is a LNI related failure and should be
handled in the same way as other LNI failures.
Reviewed-by: NDean Luick <dean.luick@intel.com>
Reviewed-by: NEaswar Hariharan <easwar.hariharan@intel.com>
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Remove the mutex guarding each operation in favor the ASIC
resource acquire/release.  Push the resource acquire/release,
above each operation call to allow exclusive access across
multiple operations.
Reviewed-by: NMitko Haralanov <mitko.haralanov@intel.com>
Reviewed-by: NEaswar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The SBus resource includes SBUS, PCIE, and THERM registers.
Change SBus handling to use the new ASIC resource reservation system.
Reviewed-by: NMitko Haralanov <mitko.haralanov@intel.com>
Reviewed-by: NEaswar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The ASIC block is a shared hardware resource between two devices
on the chip.  Add functions to acquire and release these resources
in a way that is safe for both multiple users on the same OS
and multiple users on different OSes, while holding the hardware
mutex as little as possible.

Reservations are noted in a scratch register in the shared region.
There are two types of reservations: per-HFI dynamic and permanent.
Reviewed-by: NMitko Haralanov <mitko.haralanov@intel.com>
Reviewed-by: NEaswar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

A cp or cat of /sys/kernel/debug/hfi1/hfi1_0/port1counters
produces the following message:

hfi1 0000:81:00.0: hfi1_0: index not supported
hfi1 0000:81:00.0: hfi1_0: read_cntrs does not support indexing

Fix by removing the file position logic and the associated messages
and make the file positioning the responsibility of the caller.

The port counter read function argument is changed to the per port
data structure since the counters are relative to the port and not
the device.
Reviewed-by: NSebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Fix the header by moving the copyright notice out of the license text
and to the top of the header. Also, update the copyright date.
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Fix block comments with proper formatting to fix checkpatch warnings:
WARNING: Block comments use * on subsequent lines
WARNING: Block comments use a trailing */ on a separate line
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Remove CamelCase to fix checkpatch check:
CHECK: Avoid CamelCase: <PLS_CONFIGPHY_ESTcOMM_LOCAL_COMPLETE>
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>