SIS controllers were blacklisted for PMP as enabling it made device
detection fail whether the device was PMP or not - the natural
conclusion was the controller chokes on SRST w/ pmp==15.  However, it
turned out that the controller just didn't like issuing SRST after
hardreset w/o clearing SError first.  Interestingly, the SRST itself
succeeds but the following commands fail.

If SError is cleared between hardreset and SRST, which is the default
behavior now, everything works fine and SIS controllers work with PMPs
happily.

Remove PMP blacklisting for SIS AHCIs.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Piter PUNK <piterpunk@slackware.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Commit bfce5e01 implemented custom
tf_load for pata_via.  This patch cleans it up a bit.

* Instead of duplicating whole body, copy tf and set ATA_TFLAG_DEVICE
  when necessary.

* Rename via_ata_tf_load() to via_tf_load().

* No need to set .tf_load in via_port_ops_noirq as it inherits from
  via_port_ops.

* Clean up indentation.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Save SControl during probing and restore it on detach.  This prevents
adjustments made by libata drivers to seep into the next driver which
gets attached (be it a libata one or not).

It's not clear whether SControl also needs to be restored on suspend.
The next system to have control (ACPI or kexec'd kernel) would
probably like to see the original SControl value but there's no
guarantee that a link is gonna keep working after SControl is adjusted
without a reset and adding a reset and modified recovery cycle soley
for this is an overkill.  For now, do it only for detach.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

SError belongs to link not port.  Use ata_link_printk() to print it.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

As an optimization, follow-up SRST used to be skipped if
classification wasn't requested even when hardreset requested it via
-EAGAIN.  However, some hardresets can't wait for device readiness and
skipping SRST can cause timeout or other failures during revalidation.
Always perform follow-up SRST if hardreset returns -EAGAIN.  This
makes reset paths more predictable and thus less error-prone.

While at it, move hardreset error checking such that it's done right
after hardreset is finished.  This simplifies followup SRST condition
check a bit and makes the reset path easier to modify.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

ehc->i.action got accidentally overwritten to ATA_EH_HARD/SOFTRESET in
ata_eh_reset().  The original intention was to clear reset action
which wasn't selected.  This can cause unexpected behavior when other
EH actions are scheduled together with reset.  Fix it.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The SoC sata port is based on the 7042/6042 devices (Gen IIE). This patch
will fix various issues when working with PMP and/or NCQ.
Signed-off-by: NSaeed Bishara <saeed@marvell.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch adds the Intel Ibex Peak (PCH) IDE mode SATA Controller DeviceIDs.
Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Resend with proper whitespace.

This patch adds the Intel Ibex Peak (PCH) SATA RAID Controller DeviceIDs.
Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

sata_mv allowed issuing two DMA commands concurrently which the
hardware allows.  Unfortunately, libata core layer isn't ready for
this yet and spews ugly warning message and malfunctions on this.
Don't allow concurrent DMA commands for now.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Implement force params nohrst, nosrst and norst.  This is to work
around reset related problems and ease debugging.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

After commit a97c9bf3 (fix cramfs
making duplicate entries in inode cache) in kernel 2.6.14, named-pipe
on cramfs does not work properly.

It seems the commit make all named-pipe on cramfs share their inode
(and named-pipe buffer).

Make ..._test() refuse to merge inodes with ->i_ino == 1, take inode setup
back to get_cramfs_inode() and make ->drop_inode() evict ones with ->i_ino
== 1 immediately.
Reported-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <stable@kernel.org>		[2.6.14 and later]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fixes kernel BUG at lib/radix-tree.c:473.

Previously the handler was incidentally provided by tmpfs but this was
removed with:

  commit 14fcc23f
  Author: Hugh Dickins <hugh@veritas.com>
  Date:   Mon Jul 28 15:46:19 2008 -0700

    tmpfs: fix kernel BUG in shmem_delete_inode

relying on this behaviour was incorrect in any case and the BUG also
appeared when the device node was on an ext3 filesystem.

v2: override a_ops at open() time rather than mmap() time to minimise
races per AKPM's concerns.
Signed-off-by: NIan Campbell <ijc@hellion.org.uk>
Cc: Jaya Kumar <jayakumar.lkml@gmail.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Johannes Weiner <hannes@saeurebad.de>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Kel Modderman <kel@otaku42.de>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: <stable@kernel.org> [14fcc23f is in 2.6.25.14 and 2.6.26.1]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

On a PowerPC board with ds1374 RTC I'm getting this error while RTC tries
to probe:

rtc-ds1374 0-0068: unable to request IRQ

This happens because I2C probing code (drivers/of/of_i2c.c) is specifying
IRQ0 for 'no irq' case, which is correct.

The driver handles this incorrectly, though. This patch fixes it.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

XIP can call into get_xip_mem concurrently with the same file,offset with
create=1.  This usually maps down to get_block, which expects the page
lock to prevent such a situation.  This causes ext2 to explode for one
reason or another.

Serialise those calls for the moment.  For common usages today, I suspect
get_xip_mem rarely is called to create new blocks.  In future as XIP
technologies evolve we might need to look at which operations require
scalability, and rework the locking to suit.
Signed-off-by: NNick Piggin <npiggin@suse.de>
Cc: Jared Hulbert <jaredeh@gmail.com>
Acked-by: NCarsten Otte <cotte@freenet.de>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

XIP has a race between sparse pages being inserted into page tables, and
sparse pages being zapped when its time to put a non-sparse page in.

What can happen is that a process can be left with a dangling sparse page
in a MAP_SHARED mapping, while the rest of the world sees the non-sparse
version.  Ie.  data corruption.

Guard these operations with a seqlock, making fault-in-sparse-pages the
slowpath, and try-to-unmap-sparse-pages the fastpath.
Signed-off-by: NNick Piggin <npiggin@suse.de>
Cc: Jared Hulbert <jaredeh@gmail.com>
Acked-by: NCarsten Otte <cotte@freenet.de>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There is a race with dirty page accounting where a page may not properly
be accounted for.

clear_page_dirty_for_io() calls page_mkclean; then TestClearPageDirty.

page_mkclean walks the rmaps for that page, and for each one it cleans and
write protects the pte if it was dirty.  It uses page_check_address to
find the pte.  That function has a shortcut to avoid the ptl if the pte is
not present.  Unfortunately, the pte can be switched to not-present then
back to present by other code while holding the page table lock -- this
should not be a signal for page_mkclean to ignore that pte, because it may
be dirty.

For example, powerpc64's set_pte_at will clear a previously present pte
before setting it to the desired value.  There may also be other code in
core mm or in arch which do similar things.

The consequence of the bug is loss of data integrity due to msync, and
loss of dirty page accounting accuracy.  XIP's __xip_unmap could easily
also be unreliable (depending on the exact XIP locking scheme), which can
lead to data corruption.

Fix this by having an option to always take ptl to check the pte in
page_check_address.

It's possible to retain this optimization for page_referenced and
try_to_unmap.
Signed-off-by: NNick Piggin <npiggin@suse.de>
Cc: Jared Hulbert <jaredeh@gmail.com>
Cc: Carsten Otte <cotte@freenet.de>
Cc: Hugh Dickins <hugh@veritas.com>
Acked-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When user calls sys_setpriority(PRIO_PGRP ...) on a NPTL style multi-LWP
process, only the task leader of the process is affected, all other
sibling LWP threads didn't receive the setting.  The problem was that the
iterator used in sys_setpriority() only iteartes over one task for each
process, ignoring all other sibling thread.

Introduce a new macro do_each_pid_thread / while_each_pid_thread to walk
each thread of a process.  Convert 4 call sites in {set/get}priority and
ioprio_{set/get}.
Signed-off-by: NKen Chen <kenchen@google.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Roland McGrath <roland@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Video/Framebuffer: add fuctional power management support to Blackfin BF54x LQ043 framebuffer driver

Fix bug: does nor properply resume after suspend mem
Fix for PM_SUSPEND_MEM: Save and restore peripheral base and DMA registers
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Acked-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Absolute alignment requirements may never be applied to node-relative
offsets.  Andreas Herrmann spotted this flaw when a bootmem allocation on
an unaligned node was itself not aligned because the combination of an
unaligned node with an aligned offset into that node is not garuanteed to
be aligned itself.

This patch introduces two helper functions that align a node-relative
index or offset with respect to the node's starting address so that the
absolute PFN or virtual address that results from combining the two
satisfies the requested alignment.

Then all the broken ALIGN()s in alloc_bootmem_core() are replaced by these
helpers.
Signed-off-by: NJohannes Weiner <hannes@saeurebad.de>
Reported-by: NAndreas Herrmann <andreas.herrmann3@amd.com>
Debugged-by: NAndreas Herrmann <andreas.herrmann3@amd.com>
Reviewed-by: NAndreas Herrmann <andreas.herrmann3@amd.com>
Tested-by: NAndreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If check_legacy_ioport() returns true, we leak *info.

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=11362Reported-by: NDaniel Marjamki <danielm77@spray.se>
Cc: Christian Krafft <krafft@de.ibm.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Corey Minyard <minyard@acm.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Release cmap memory allocated in the probe function.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

With commit 5ad31a57 ("rtc: remove BKL
for ioctl()"), RTC_UIE_ON ioctl cause double lock on rtc->ops_lock.
The ops_lock must not be held while set_uie() calls rtc_read_time()
which takes the lock.  Also clear_uie() does not need ops_lock.  This
patch fixes return value of RTC_UIE_OFF ioctl too.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: David Brownell <david-b@pacbell.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In case the binfmt_misc binary handler is registered *before* the e.g.
script one (when for example being compiled as a module) the following
situation may occur:

1. user launches a script, whose interpreter is a misc binary;
2. the load_misc_binary sets the misc_bang and returns -ENOEVEC,
   since the binary is a script;
3. the load_script_binary loads one and calls for search_binary_hander
   to run the interpreter;
4. the load_misc_binary is called again, but refuses to load the
   binary due to misc_bang bit set.

The fix is to move the misc_bang setting lower - prior to the actual
call to the search_binary_handler.

Caused by the commit 3a2e7f47 (binfmt_misc.c: avoid potential kernel
stack overflow)
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Reported-by: NKirill A. Shutemov <kirill@shutemov.name>
Tested-by: NKirill A. Shutemov <kirill@shutemov.name>
Cc: <stable@kernel.org>		[2.6.26.x]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The name of brd block device is "ramdisk", it's not "brd".
(The block device is registered by register_blkdev(RAMDISK_MAJOR, "ramdisk")
So it should be unregistered by unregister_blkdev(RAMDISK_MAJOR, "ramdisk")
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Acked-by: NNick Piggin <npiggin@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We leak the memory allocated for the nbd_dev array at multiple places.
Fix them by either adding a kfree() or by rearranging code to return
before we allocate the memory.
Signed-off-by: NSven Wegener <sven.wegener@stealer.net>
Cc: Paul Clements <paul.clements@steeleye.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

mminit_loglevel is now used from mminit_verify_zonelist <- build_all_zonelists <-

1. online_pages <- memory_block_action <- memory_block_change_state <- store_mem_state (sys handler)
2. numa_zonelist_order_handler (proc handler)

so it cannot be annotated __meminit - drop it

fixes following section mismatch warning:
WARNING: vmlinux.o(.text+0x71628): Section mismatch in reference from the function mminit_verify_zonelist() to the variable .meminit.data:mminit_loglevel
The function mminit_verify_zonelist() references
the variable __meminitdata mminit_loglevel.
This is often because mminit_verify_zonelist lacks a __meminitdata
annotation or the annotation of mminit_loglevel is wrong.
Signed-off-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Acked-by: NMel Gorman <mel@csn.ul.ie>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Adjust <Alt><SysRq>m show_swap_cache_info() to show "Free swap" as a
signed long: the signed format is preferable, because during swapoff
nr_swap_pages can legitimately go negative, so makes more sense thus
(it used to be shown redundantly, once as signed and once as unsigned).
Signed-off-by: NHugh Dickins <hugh@veritas.com>
Reviewed-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add a comment to s390's page_test_dirty/page_clear_dirty/page_set_dirty
dance in page_remove_rmap(): I was wrong to think the PageSwapCache test
could be avoided, and would like a comment in there to remind me.  And
mention s390, to help us remember that this block is not really common.

Also move down the "It would be tidy to reset PageAnon" comment: it does
not belong to s390's block, and it would be unwise to reset PageAnon
before we're done with testing it.
Signed-off-by: NHugh Dickins <hugh@veritas.com>
Acked-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NGraf Yang <graf.yang@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Blackfin RTC Driver: move irq request/free out of open/release and into probe/remove so that the non-dev interfaces (like sysfs) work as expected
Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This addresses

	http://bugzilla.kernel.org/show_bug.cgi?id=11318

In function show_map (file: fs/proc/task_mmu.c), if vma->vm_pgoff > 2^20
than (vma->vm_pgoff << PAGE_SIZE) is greater than 2^32 (with PAGE_SIZE
equal to 4096 (i.e.  2^12).  The next seq_printf use an unsigned long for
the conversion of (vma->vm_pgoff << PAGE_SIZE), as a result the offset
value displayed in /proc/self/maps is truncated if the page offset is
greater than 2^20.

A test that shows this issue:

#define _GNU_SOURCE
#include <sys/types.h>
#include <sys/stat.h>
#include <sys/mman.h>
#include <stdlib.h>
#include <stdio.h>
#include <fcntl.h>
#include <unistd.h>
#include <string.h>

#define PAGE_SIZE (getpagesize())

#if __i386__
#   define U64_STR "%llx"
#elif __x86_64
#   define U64_STR "%lx"
#else
#   error "Architecture Unsupported"
#endif

int main(int argc, char *argv[])
{
	int fd;
	char *addr;
	off64_t offset = 0x10000000;
	char *filename = "/dev/zero";

	fd = open(filename, O_RDONLY);
	if (fd < 0) {
		perror("open");
		return 1;
	}

	offset *= 0x10;
	printf("offset = " U64_STR "\n", offset);

	addr = (char*)mmap64(NULL, PAGE_SIZE, PROT_READ, MAP_PRIVATE, fd,
			     offset);
	if ((void*)addr == MAP_FAILED) {
		perror("mmap64");
		return 1;
	}

	{
		FILE *fmaps;
		char *line = NULL;
		size_t len = 0;
		ssize_t read;
		size_t filename_len = strlen(filename);

		fmaps = fopen("/proc/self/maps", "r");
		if (!fmaps) {
			perror("fopen");
			return 1;
		}
		while ((read = getline(&line, &len, fmaps)) != -1) {
			if ((read > filename_len + 1)
			    && (strncmp(&line[read - filename_len - 1], filename, filename_len) == 0))
				printf("%s", line);
		}

		if (line)
			free(line);

		fclose(fmaps);
	}

	close(fd);
	return 0;
}

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NClement Calmels <cboulte@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

"bootmem_debug" is not mentioned in kernel-parameters.txt. Recently I
had to use that kernel option and I think it should be documented.
Signed-off-by: NAndreas Herrmann <andreas.herrmann3@amd.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Johannes Weiner <hannes@saeurebad.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

eeepc-laptop uses the hwmon struct after unregistering the device, causing
an oops on module unload.  Flip the ordering to fix.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Karol Kozimor <sziwan@users.sourceforge.net>
Cc: <stable@kernel.org>		[2.6.26.x]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Provide ioremap_wc() for FRV.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Supply ioremap_wc() for MN10300.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Purely cosmetic for now, but we might as well get it merged ASAP.
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>